Winegard SENSAR III ANTENNA Bedienungsanleitung

WINEGARD®

INSTALLATION/OPERATION MANUAL (All Models)

MADE IN U.S.A.

(Sensar® III head - U.S. Patent D500,496)

(WINGMAN® - U.S. Patent D612,369)

(Sensar® IV head - U.S. Patent D620,483)

WINEGARD®SENSAR®ANTENNAS

• Increases UHF performance up to 100%

• FREE digital programming

• Installs in minutes -

no tools required

•RV-WING – White, RV •GS-WING – Gray, Residential

Sensar only Sensar with

Wingman

VHF UHF VHF UHF

Excellent

Digital

Reception

Great

Digital

Reception

Digital Reception

Sensar vs Sensar with Wingman

Channels

14-51

Channels

2-13 Channels

14-51

Channels

2-13

SENSAR®III ANTENNA

WITH WINGMAN®

ACCESSORY

Printed in U.S.A. Winegard Company • 3000 Kirkwood Street • Burlington, Iowa 52601-2000 © Winegard Company, 2004, 2006 2452013 REV9 5/13

SENSAR®ANTENNA

WITH WINGMAN®-

SENSAR® IV ANTENNA

NOTE: Maintain a minimum of 10" from the edge of the roof or any

obstruction (16" must be maintained if installing a Sensar IV). Check

with your dealer or the manufacturer for information about options

in the roof for mounting the antenna. A reinforced roof area, or a

prewired coax cable, may be available. For sloped/round roofs, use

Winegard Model RW-2000 exterior roof wedge, to level installation. An

interior wedge, IW-5000, is also available.

STEP 2: Using template on our website at http://www.winegard.com/

kbase/upload/sensar_template.pdf drill 1-3/4" hole through roof and

ceiling of vehicle. Be careful not to damage any wiring between roof and

ceiling.

STEP 3: Drill 1/2" hole for cable entry through roof of vehicle only. DO

NOT DRILL THROUGH CEILING. Route cable through ceiling and wall to

power supply location.

STEP 4: The mount is designed to t roofs from 1" to 4-3/4" thick. As

supplied, the mount will t a roof 4-3/4" thick. If roof is less than 4-3/4"

thick, cut elevating shaft and directional handle to size, steps shown

in gures 2, 3, 4 and 5. If roof is more than 4-3/4" thick (max. 7"), a

directional handle extension is needed. Order Winegard Model

EK-1036, Directional Handle Extension.

IMPORTANT: The handle and extension must be glued together after

checking that you have the correct length. The handle will not work

properly if it is not glued together! (PVC glue is recommended; for your

safety, use according to manufacturer's directions.)

NOTE: If using roof wedge RW-2000 or interior wedge IW-5000, put in

place before installing base plate or interior hardware.

2452013-Installation/Operation

STEP 1: Choose location for antenna. Figure 1 illustrates placement of the Sensar, showing it in travel position.

You must be able to raise and rotate antenna without interfering with other roof-mounted equipment. Make sure

inside ceiling area is clear to mount ceiling plate.

STEP 5: Center elevating shaft in hole on

roof. Temporarily secure base plate to roof

with two screws provided. (Do not apply

sealant at this time). Inside unit, make a

mark on the shaft 1-1/2” below ceiling and cut

shaft on this mark. See gure 2.

After cutting elevating shaft, push directional

handle up into ceiling over shaft being careful

to align keys inside directional handle onto

keyways on bottom of gear housing. (NOTE:

The keys only line up one way; do not force.

TIP: Pointer on directional handle should

point toward back of coach if properly

installed.) Make sure directional handle is snug

against bottom of baseplate. Measure distance

between the bottom of the recess on the handle

to the ceiling. See gure 3. Pull handle back

down and transfer this dimension to the shaft

end of the directional handle. Mark it and cut it

off here, g. 4.

If EK-1036 (directional handle extension) is

used, DO NOT CUT EK-1036 extension. Cut

excess length from directional handle only. The

handle and extension must be glued together

after checking that you have the correct length,

g. 5.

FIGURE 1

10" Minimum

Distance

If installing a Sensar® IV, a

minimum distance of 16" must

be maintained from the edge of the

roof and from the nearest obstruction.

10" 10"

10"

To Nearest

Obstruction

10"

2′

10"

FRONT OF VEHICLE

ALL MODELS

STEP 6: Attach antenna head to lift tubes with two (2)

steel pins, Figure 6. Align holes in leveling bracket on

back of antenna head with holes in lift tubes, insert

pins and secure in place with (2) E-clips. Use pliers

and get a rm grip on E-clips. Fit clips into groove

on pins and snap into place.

STEP 7: On models made before March, 2004,

attach coax connector to jack on back of antenna

head, slide weather boot into place over boot collar;

shown in Figure 7A. On models made after March,

2004, attach weather resistant coax connector to jack

on back of antenna head; shown in Figure 7B.

STEP 8: Mount antenna and lift on roof in travel

position. Apply a liberal amount of approved

nonhardening sealing compound on bottom of base

plate and roof area around hole, Figure 8. Secure

base plate with screws provided. Apply sealing

compound over mounting screws, Figure 8.

STEP 9: Lay ceiling plate on top of directional

handle with pointers aligned and slide assembly over

rotating base shaft in ceiling. Make pilot holes in

ceiling. Mount ceiling plate with directional handle

in place with screws provided, Figure 9.

STEP 10: Assemble directional handle, spring, nylon

bearing, directional handle decal and elevating crank

as shown in exploded view in Figure 9. Remove

backing from crank cover decal and press rmly

inside directional handle. Slide all parts over elevating

shaft and install elevating crank so set screw is on

one of the six at sides of elevating shaft before

tightening screw.

WARNING: Once set screw touches shaft, tighten

only 1/4 turn more. Set screw simply holds

elevating crank on. DO NOT OVERTIGHTEN!

NON-AMPLIFIED MODELS ONLY

STEP 11: Run downlead to TV set location and make

connection to antenna terminals of TV set.

Coax Connection

FIGURE 7B

NOTE:

Apply non-hardening

sealing compound

such as Butyl

caulking between

Base

Plate and roof

of vehicle

CAUTION:

Do not get sealing compound on bearing surface between base

plate and Rotating Gear Housing. Do not paint top of Base

Plate or around Rotating Gear Housing.

FIGURE 8 CEILING PLATE

DIRECTIONAL

HANDLE

SPRING

DECAL

NYLON BEARING

ELEVATING CRANK

FIGURE 9

POINT TO REAR

OF COACH

FIGURE 6 Leveling Bracket

(2) Steel Pins

Lift Tubes

(2) E-Clips

Antenna

Head

FIGURE 7A Weather

Boot

Coax Connection

Boot Collar

Cable Input

Set 2

Output

Antenna

Downlead

AMPLIFIED MODELS ONLY

STEP 11: Select location for wall plate. Run two

coax cables (RG-6 type recommended) (three if set 2

jack is going to be used) between locations and install

connectors on each end. Mark cables so "cable

input", "TV output" "Set 2" may be identied.

Antenna downlead and ltered 12 VDC power source

will also be needed at inside wall plate/power supply

location.

STEP 12: The wall plate/power supply assembly

may be ush mounted in most standard electrical

boxes. To ush mount cut a hole in wall to t the box.

Run 2 #12 wires between wall plate/power supply

and ltered 12 VDC source and route downlead cable

to this location.

CAUTION

THE POWER SUPPLY SHOULD BE TURNED OFF

WHEN CONNECTING CABLES/WIRES TO POWER

SUPPLY. SEE FIGURE 14.

STEP 13: Make 12 volt connection to wall plate/pow-

er supply, Figure 10. Install terminals on wires from

ltered 12 VDC source, Figure 11. Crimp terminals

with appropriate crimping tool or equivalent, Figure

12. Push wires onto tabs on terminal board as shown

in Figure 10. If in doubt as to the polarity of the wires,

connect them temporarily to tabs on circuit board and

press ON switch on front of wall plate; if light comes

on, polarity is correct, Figure 10.

STEP 14: Install connectors on downlead, set 2 and

cable input cables as shown on page 6. Attach down-

lead cable to jack on wall plate/power supply marked

antenna, Figure 13. Attach cable going to set 2 output

to jack on power supply marked SET 2. Attach cable

coming from cable input to jack on power supply

marked CABLE.

STEP 15: Mount power supply in wall with screws

provided and attach TV set cable to jack on front of

power supply/wall plate. Press ON switch on front of

wall plate and check that light is on, Figure 14.

CHECKING OPERATION OF POWER SUPPLY

1. Tune TV receiver to nearest station and rotate

antenna for best picture and sound.

2. Press OFF switch on power supply. Picture on TV

should be considerably degraded with power off.

3. This unit is equipped with a polyswitch, (current

limiting device), which will shut down +12 VDC if

there is a direct short between antenna and power

supply. Green indicator light will not light. Once short

is eliminated, device will reset itself.

ADDING OPTIONAL AMPLIFIED WALLPLATE TO

NON-AMPLIFIED RV/TV INSTALLATION

Model RA-7596 solid state TV signal amplier works

with any non-amplied RV/TV antenna. Improves

picture quality. Uses +12 VDC; has on/off switch,

indicator light, set 2 output, cable input and +12 VDC

receptacle.

-12 VDC

(Ground)

FIGURE 12

FIGURE 13

FIGURE 14

WARNING

DO NOT connect high

current devices such

as hair dryers to this

receptacle. Maximum

current rating of this

receptacle is 8 amps at

+12 VDC.

FIGURE 11

Connector

Ferrule

Crimp Here

1/4" #12 Wire

Remove 1/4" of insulation

from #12 wire.

Connector

Insulation

FIGURE 10

+12 VDC

Rev. 8/10

RAISING ANTENNA TO OPERATING POSITION

Turn elevating crank (clockwise) in “UP” direction

about 13 turns or until some resistance to turning is

noted.

AMPLIFIED MODELS ONLY

Turn power supply ON to use either front or rear

TV outlet. Neither outlet will work unless power

supply switch is ON.

ROTATING ANTENNA FOR BEST PICTURE

Make sure antenna is

in “UP” position. Pull

down with both hands to

disengage ceiling plate.

Rotate for best picture.

LOWERING ANTENNA TO TRAVEL POSITION

Rotate antenna until pointer on directional handle

aligns with pointer on ceiling plate. Turn elevating

crank (counter clockwise) in “DOWN” direction about

13 turns or until resistance is noted. Antenna is now

locked in travel position.

IMPORTANT: Under no conditions should the

antenna be raised while traveling.

DO’S

1. Check parking location for obstructions before raising

antenna.

2. Carefully raise, lower and rotate. If this is difcult, check

for cause.

3. Rotate slowly when selecting station and check ne

tuning on TV set to make sure it is properly adjusted.

4. Lower antenna before moving vehicle.

DONT'S

1. Don’t force elevating crank up or down.

2. Don’t rotate directional handle hard against stops.

3. Don’t travel with lift in up position.

4. Don’t leave lift part way up or down.

5. Don’t apply sealing compound or paint over top of base

plate or anywhere on lift.

LUBRICATION (Done 3-4 times annually)

STEP 1: To lubricate the elevating gear, apply a

liberal amount of silicone spray lubricant to the

elevating gear with the lift in the down position (see

illustration). Run the lift up and down to distribute the

lubricant over gears.

STEP 2: Two times yearly, or in the event rotating the

antenna becomes difcult, normal operation can be

restored by lubricating the bearing surface between

the rotating gear housing and the base plate. Any

silicone lubricant spray may be used. Elevate

antenna and remove plastic plug from rotating gear

housing as shown. Spray lubricant into hole and

around edges of gear housing. Rotate gear housing

until lubricant coats bearing surfaces and antenna

rotates freely.

LUBRICATING RUBBER QUAD RING

Lubricate rubber quad ring on elevating

shaft which is below worm gear with

silicone spray lubricant at least twice

yearly. This will keep quad ring from

becoming brittle which could result

in leaks down elevating shaft. Refer

to page 7 for removing worm gear

assembly. Item #7 on parts explosion.

DO NOT connect high

current devices such

as hair dryers to this

receptacle. Maximum

current rating of this

receptacle is 8 amps at

+12 VDC.

OPERATION MANUAL (All Models)

WINEGARD SENSAR ANTENNAS

®®

Wave

Washer

Flat

Washer

Rubber

Ring

WHAT TO DO WHEN YOUR RV/TV ANTENNA IS NOT WORKING PROPERLY

Step 1. Strip outer cover back 1/2"* from end of cable. Fray braid back as far as outer

cover will allow.

Step 2. Trim braid close to outer cover and remove 1/4"* of inner insulation being

careful not to nick center conductor. Make sure no foil or braid can touch center

conductor.

Step 3. Slide connector tip between braid and inner insulation (braid and foil, on foil

shield cable) and push connector on cable as far as it will go. Crimp built-in ferrule with

proper crimping tool. Hex connector requires hex crimping tool. Do Not crush cable

out-of-round.

*If installing in very hot weather, increase these dimensions 1/8".

WARNING

Do not install couplers, splitters, etc. between the

power supply and the antenna. Installation of any

item on the downlead may cause a short in the

system. The downlead supplies +12 VDC to the

preamp in the antenna.

Turning power supply on sends +12 VDC up

cable to antenna. Voltage energizes transistors on

amplier in antenna head. TV signal comes back

down cable to outlets.

TO TEST SYSTEM, Figure 2

1. Make sure TV set is working properly.

2. Switch power supply ON and OFF watching

for difference in picture quality. If there is NO

difference, use following steps.

CAUTION: The power supply should be turned

OFF when connecting/disconnecting cables to

power supply and antenna, but should be turned

ON when testing for voltage.

3. Disconnect cable from antenna and check for

+12 VDC at Test Point #1. If there is +12 VDC, the

power supply is OK. Replace antenna.

4. If there is NO +12 VDC at Test Point #1,

reconnect cable to antenna. Remove power supply

from wall and visually inspect for burned/broken

parts. If there are ANY broken/burned parts,

replace power supply.

5. Disconnect cable from antenna jack on power

supply. Check for +12 VDC at Test Point 2. If

+12 VDC is present, there is a cable problem

connecting the power supply to the antenna.

Repair/replace cable.

6. If +12 VDC is not present at Test Point # 2, be

sure the green indicator light is ON. If not, check

the polarity of the red/white wires and the +12 VDC

source. If there is still no +12 VDC, replace power

supply.

HOW YOUR SYSTEM WORKS, Figure 1

Figure 2

INSTALLING F-CONNECTORS ON COAXIAL CABLE

TEST POINT #1

+12 VDC at Antenna

White

GND.

2ND Set

No +12 VDC

at this point

Set 2

Connection

+12 VDC

Antenna

Jack

TEST

POINT #2

Red

+12 VDC

2ND Set

Hook Up

No +12 VDC

at this point

Antenna

Connection

Amplied

TV Signal

GND.

White

Set 2

+12VDC

Red

+12 VDC

Figure 1

Rev. 8/10

Worm Gear

& 12.25" Hex

Elevating Shaft

Assembly w/

Wave Washer

Flat Washer

"O" Ring

Worm Gear Nut

WHITE

Directional Handle

Ceiling Plate

4 Screws

Spring

Decal

ORDERING REPAIR PARTS

Repair parts are available at many RV dealers and/or service centers throughout the country. If you don't have

a dealer/service center near you, call Winegard Company at 1-800-288-8094. All major credit cards accepted.

Parts are available only in the packages shown here. Order by the Model No. of the package needed.

Example: To order the elevating gear, order RP-3000. Tax, shipping and handling additional.

Rev. 11/09

PACKAGE MODEL NO.

RV-WING

Digital

Accessory

RP-RV04

4 Rivets for

Wingman

** Use 3/32 Allen Wrench for set screw.

* Remove/tighten with 15/16" 12 socket.

RP-2658

Nylon Bearing

Spring

RP-6822

Base Plate

10 Screws

Rubber Boot

RP-3523

RP-0154

Boot

RP-3000

Elevating Gear

RP-4000

RP-6300

IVORY

Directional Handle

Ceiling Plate

4 Screws

Spring

Decal

RP-6200

RW-2000

Roof Wedge

Interior Wedge

16 IW-5012

EK-1036

Directional

Handle

Extension

17 11

Flat Washer

Wave

Washer

Rubber

Quad Ring

Use boot for coax connection

on models made before 3/2004.

PACKAGE MODEL NO.

RP-2049

Gear Housing

2 Pins

Bearing

Nut *

Bearing

O-Ring Seal

Retaining Ring

FITS ALL

Preassembled

Elev. Shaft, Gear

Hsg.,Base Plate

14 SA-1001 IVORY

RP-6795

NEW 1993

WHITE

Crank,

Set Screw

RP-5895

IVORY

AFTER 1989

Crank,

Set Screw

See

Drawing

at Right

22120566

Non-Amplied

Antenna Head

75 ohm

2RV-2005

Amplied

Antenna Head

75 ohm

2RVW-205

Amplied (white)

Antenna Head

75 ohm with

Wingman

2RVW205B

Amplied (black)

Antenna Head

75 ohm with

Wingman

2 Elevator Tubes

2 Grommets

4 Pins

4 Retaining Rings

Rubber Bumper

Self Drilling

RP-2900

Leveling Mount

4 Spacers

2 Pins

2 Rings

RP-2000

FOR MODELS MADE

BEFORE 1990

Printed in U.S.A. Winegard Company • 3000 Kirkwood Street • Burlington, Iowa 52601-2000 © Winegard Company, 2004, 2006 2452013 REV9 5/13

WS-MOBWARREV2

Rev. 1/10

WINEGARD MOBILE PRODUCTS LIMITED WARRANTY

(2 YEARS PARTS; 1 YEAR LABOR)

Winegard Company warrants this product against defects in materials or workmanship for a period of two (2) years from the date of original purchase. During

year one (1) of such warranty, Winegard Company will also pay authorized labor costs to an authorized Winegard dealer to repair or replace defective products.

No warranty claim will be honored unless at the time the claim is made, Customer presents proof of purchase to an authorized Winegard dealer (to locate

the nearest authorized Winegard dealer, contact Winegard Company, 3000 Kirkwood Street, Burlington, Iowa 52601, Telephone 800-288-8094 or visit www.

winegard.com). Customer must provide proof of purchase with a dated sales receipt for the Winegard product to verify the product is under warranty. If the

date of purchase cannot be veried, the warranty period shall be considered to begin thirty (30) days after the date of manufacture.

If a defect in material or workmanship is discovered, Customer may take the product to an authorized Winegard dealer for service. Customer must provide proof

of purchase to verify the product is under warranty. If the product is brought to an authorized Winegard dealer for service prior to expiration of year one (1) of

the warranty period and a defect in material or workmanship is veried by Winegard Technical Services, Winegard Company will cover the Winegard dealer’s

labor charges for warranty service. The Winegard dealer must contact Winegard Technical Services in advance for pre-approval of the service. Approval of

the service is at the sole discretion of Winegard Company.

Alternatively, Customer may ship the product prepaid to Winegard Technical Services (located at 3111 Kirkwood Street, Burlington, Iowa 52601, Telephone

800-788-4417). Customer must return the product along with a brief description of the problem and provide Winegard Technical Services with Customer’s

name, address, and phone number. Customer must also provide proof of purchase to verify the product is under warranty. If the product is returned before

the expiration of the warranty period, Winegard Company will (at its option) either repair or replace the product.

This Limited Warranty does not apply if the product has been damaged, deteriorates, malfunctions or fails from: improper installation, misuse, abuse, neglect,

accident, tampering, modication of the product as originally manufactured by Winegard in any manner whatsoever, removing or defacing any serial number,

usage not in accordance with product instructions or acts of nature such as damage caused by wind, lightning, ice or corrosive environments such as salt

spray and acid rain. This Limited Warranty also does not apply if the product becomes unable to perform its' intended function in any way as a result of the

television signal provider making any changes in technology or service.

RETURN AUTHORIZATION POLICY

A Return Material Authorization (RMA) is required prior to returning any product to Winegard Company or Winegard Warranty Services under this warranty

policy. Please call our Technical Services Department at 800-788-4417 or send an email to [email protected] to obtain the RMA number. Please furnish

the date of purchase when requesting an RMA number. Enclose the product in a prepaid package and write the RMA number in large, clear letters on the

outside of the package. To avoid confusion or misunderstanding, a shipment(s) without an RMA number(s) or an unauthorized return(s) will be refused and

returned to Customer freight collect.

WINEGARD COMPANY DOES NOT ASSUME ANY LIABILITIES FOR ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, MADE BY ANY OTHER

PERSON.

ALL OTHER WARRANTIES WHETHER EXPRESS, IMPLIED OR STATUTORY INCLUDING WARRANTIES OF FITNESS FOR A PARTICULAR PURPOSE

AND MERCHANTABILITY ARE LIMITED TO THE TWO YEAR PERIOD OF THIS WARRANTY.

In states that do not allow limitations on implied warranties, or the exclusion of limitation of incidental or consequential damages, the above limitations or

exclusions do not apply.

Some states do not allow limitations on how long an implied warranty lasts, or the exclusion of limitation of incidental or consequential damages, so the above

limitations or exclusions may not apply to you.

This warranty gives Customer specic legal rights. Customer may also have other rights that may vary from state to state.

SATELLITE RECEIVER WARRANTY:

See manufacturer’s limited warranty policy.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Winegard Antenne Handbücher

Winegard

Winegard RZ-7500 Bedienungsanleitung

Winegard

Winegard PR-8800 Bedienungsanleitung

Winegard

Winegard Movin' View MV-0022 Bedienungsanleitung

Winegard

Winegard WV750 Bedienungsanleitung

Winegard

Winegard RoadTrip SD Bedienungsanleitung

Winegard

Winegard HD-6000 Bedienungsanleitung

Winegard

Winegard SK-7003 Mount Bedienungsanleitung

Winegard

Winegard dish Playmaker Bedienungsanleitung

Winegard

Winegard GM-9000 Bedienungsanleitung

Winegard

Winegard Movin' View MV-0500 Bedienungsanleitung

Winegard

Winegard Movin' View MV-1111 Bedienungsanleitung

Winegard

Winegard DuraSAT D4 CM2000T Bedienungsanleitung

Winegard

Winegard YA-1713 Bedienungsanleitung

Winegard

Winegard Rayzar.Air RVRZ25W Bedienungsanleitung

Winegard

Winegard Pathway X1 Bedienungsanleitung

Winegard

Winegard TRAV'LER DIRECTV SK-SWM3 Bedienungsanleitung

Winegard

Winegard HD7210P Bedienungsanleitung

Winegard

Winegard Sensar HV CC-10HV Bedienungsanleitung

Winegard

Winegard Movin' View MV3500A Bedienungsanleitung

Winegard

Winegard AIR 360+ Bedienungsanleitung

Winegard

Winegard HD7000R Bedienungsanleitung

Winegard

Winegard HD7078P Bedienungsanleitung

Winegard

Winegard Movin' View MV3535A Bedienungsanleitung

Winegard

Winegard TR-6018 Bedienungsanleitung

Beliebte Antenne Handbücher anderer Marken

Alfa Network

Alfa Network APA-L01 Bedienungsanleitung

Naval

Naval PR-422CA Bedienungsanleitung

Feig Electronic

Feig Electronic ID ISC.ANTH200/200 Series Bedienungsanleitung

TERK Technologies

TERK Technologies TV44 Bedienungsanleitung

Directive Systems & Engineering

Directive Systems & Engineering DSE2324LYRMK Bedienungsanleitung

HP J8999A Bedienungsanleitung

MobilSat

MobilSat MSP-S Bedienungsanleitung

Steren

Steren ANT-UHF 13 Bedienungsanleitung

Novatel

Novatel 600-G Bedienungsanleitung

Radio Shack

Radio Shack Amplified VHF/UHF/FM Indoor Antenna Bedienungsanleitung

TRENDnet

TRENDnet TEW-AO12O Bedienungsanleitung

Radio Shack

Radio Shack 15-1837 Bedienungsanleitung

CommScope

CommScope CMAX-OMFX-43M-I53 Bedienungsanleitung

Ramsey Electronics

Ramsey Electronics DAP25 Bedienungsanleitung

COBHAM

COBHAM SAILOR 800 VSAT Gebrauchs- und Pflegehandbuch

Trango Systems

Trango Systems AD900-9 Bedienungsanleitung

Steren

Steren ANT-100 Bedienungsanleitung

IWCS

IWCS iriBelt II Einrichtungshandbuch