Winegard RoadTrip SD Bedienungsanleitung

RoadTrip™

Digital Satellite Mobile Antenna for Two Receivers

RoadTrip SD - Stationary Satellite System

RoadTrip SDi - In-Motion Satellite System

INSTALLATION MANUAL

Made in the U.S.A.

Winegard Company • 3000 Kirkwood St. • Burlington, IA 52601-2000

319/754-0600 • FAX 319/754-0787 • www.winegard.com

Printed in U.S.A. © Winegard Company, 2006 2452086

WINEGARD®

1. Open box and remove packing material.

2. Lift dome out of box vertically. Then lift unit out of

box vertically. Do not turn box and “roll” out, or turn

upside down to remove.

4’ Gray Coax Cable (OEM Model)

4’ White Coax Cable (OEM Model)

4’ Power Cable (OEM Model)

Parts Included • Tools Needed • How to Unpack

If using knife to open

carton, BE CAREFUL.

Do not cut the dome on

the unit.

1 Radome

1 Cable entry plate

All required screws, washers, bolts, and nylocks

1 base with electronics, dish, dual LNBF,

mounting feet

LIFT UNIT STRAIGHT UP

OUT OF CARTON!

UNPACKING THE UNIT

PARTS INCLUDED:



The Winegard RoadTrip is designed specifically for use with motorized recreational

vehicles. Winegard recommends using a qualified installer familiar with RV structure and

wiring to ensure proper installation and to prevent damage to RV or dish.

REV. 12/05

USE 2 PEOPLE

when removing the unit

from the carton.

!DO NOT PAINT DOME!

Painting dome will

cause signal

degradation and will

void your warranty.

TOOLS NEEDED FOR UNPACKING & INSTALLATION:

Level

Drill w/3/4” bit

1-1/4” hole saw (if mounting switch in wall)

Phillips screw driver #2

3/8” Open end wrench

7/16” Open end wrench

Sealant (consult RV manufacturer for proper type

for your roof material)

Installation Diagram

Control Unit

ELEVATION

MOTOR

LNBF



CONTROL UNIT MUST

BE PARALLEL TO THE

CENTER LINE OF THE

VEHICLE AND FACE

FRONT OR REAR OF

VEHICLE.

CENTER

LINE OF THE

VEHICLE



GPS CABLE

(RoadTrip SDi

ONLY)

GPS ANTENNA

(RoadTrip SDi ONLY)



Quick Reference Guide

Your Winegard RoadTrip satellite System has been designed to be the most user-friendly

Mobile Satellite Antenna on the market today. Upon installation of the antenna, or after

changing satellite service provider, simply set the switches inside of the dome to the settings

shown in the Operation manual. These switches enable the dish to locate the proper satellite

for your service provider, and, for the RoadTrip SDi In-Motion system, to be set for the proper

installation option. Simply set the switch, and forget it! Your Winegard RoadTrip Satellite

Antenna will locate the proper satellite with just the flip of a switch.

Mounting Instructions

It is essential to mount your RoadTrip Automatic System in the proper position and orientation

on your RV roof to ensure proper operation. Choose a location on your roof clear of

obstruction and close to your receiver and power source.

To ensure proper tracking with your RoadTrip SDi, you must mount the unit so that the unit is

centered on the centerline and cables exit either towards the front or back of the RV. See

Figure 1c below.

MOUNTING OPTION A

CABLE EXIT REAR

CENTER LINE OF VEHICLE

MV-3500

BACK OF VEHICLE

FRONT OF VEHICLE

ROADTRIP

CABLE EXIT FRONT

CENTER LINE OF VEHICLE

MV-3500

BACK OF VEHICLE

FRONT OF VEHICLE

FIGURE 1C

MOUNTING OPTION B

ROADTRIP

Switch Settings

After mounting the RoadTrip System to your rooftop, you must set the RoadTrip’s switch

settings for the mountoing options chosen and satellite Television Service Provider. The chart

below lists switch settings for both the RoadTrip SD and RoadTrip SDi. See page 3. of

Operation Manual for detailed instructions.

RoadTrip SD

(#1 represents Switch DOWN; #0 represents Switch up)

Sat. Rcvr. Mt. Option Switch Set Position

................................... 1 2 3 4 5 6 7 8

DIRECTV A 0 0 0 0 0 0 0 1

(FACTORY PRESET)

DISH NETWORK A 0 0 0 1 0 0 1 1

1 2 3 4 5 6 7 8

SWITCH SETTINGS

SHOWN

0= UP 1= DOWN

  

1 = DOWN

0 = UP 0 0 0 0 0 0 0 1

RoadTrip SDi

(#1 represents Switch DOWN; #0 represents Switch up)

Sat. Rcvr. Mt. Option Switch Set Position

..................................... 1 2 3 4 5 6 7 8

DIRECTV A 0 0 0 0 0 0 0 1

(FACTORY PRESET)

DIRECTV B 1 0 0 0 0 0 0 1

DISH NETWORK A 0 0 0 1 0 0 1 1

DISH NETWORK B 1 0 0 1 0 0 1 1

1 2 3 4 5 6 7 8

SWITCH SETTINGS

SHOWN

0= UP 1= DOWN

  

1 = DOWN

0 = UP 0 0 0 0 0 0 0 1

™

TM TM

IMPORTANT! Do not install this system

in the rain, or under any wet conditions. Mois-

ture may affect electronics and void your

warranty!

1. For best performance and to reduce signal ac-

quisition time, park vehicle on a level surface;

level the RV.

2. Select a level spot on your roof for installation.

Using the chart,

determine the

minimum distances

to other equipment.

WARNING: Level the base front to back and side

to side. If base is not level the RoadTrip may re-

quire more time to locate the correct satellite or

may not locate the correct satellite.

• Be sure no roof-mounted equipment is

blocking the satellite “line of sight”, Fig. 3

Installation

Install in DRY conditions only!

Installing unit on roof of vehicle —

Obstruction Ht. Unit Clearance

8” ...................................... 2”

10” .................................... 8”

12” .................................. 13”

15” .................................. 22”

FIGURE 3

OBSTRUCTION

UNIT BASE

3. After selecting location for unit (see number 2),

put the unit on the centerline of the vehicle.

4. Position base so that cables exit either toward

the rear (Mounting Option A) or toward the front

(Mounting Option B) of vehicle.

Electronics box MUST be parallel to the center

line of the vehicle. See page 4.

6. Clean roof area where the base feet will be

attached to the roof. Do not erase your marks!

7. Put approved sealant in the areas marked

for the base feet. Place base feet on top of the

sealant and screw down with the (3) #10

screws for each foot.

8. After all base feet are secured to roof, put

sealant around edge of feet and over screws.

FIGURE 5, Mounting Option A shown

5. Place the unit on the roof in its permanent loca-

tion and mark around each base foot, Figure 4.

FIGURE 4

A’ B’

ROADTRIP

Front of Vehicle

Center Line

The distance from the edge of the roof to the

rear corner of the foot should be equal on both

sides of the dish to ensure proper installation.

Installation

1. Connect coax cables and power wire to RV pre-

wire harness. Connect gray coax to pre-wire coax for

primary receiver. Connect white coax to pre-wire coax

for secondary receiver. Connect power cable to pre-

wire power cable. See Figure 2.

2. Place cable-entry plate over hole and cables.

Screw in place. Seal plate and screw holes with ap-

proved sealant (not included).

Cable entry installation —

INSTALLING THE POWER SWITCH

1. Choose a location to install the RoadTrip power

ON/OFF switch. Remember when selecting a location

that you will need to run the +12VDC power cable

from the RoadTrip to the switch. Be sure the

switch is in the OFF position before continuing.

See Figure 7 page 9.

Wall or panel mount: Drill 1-1/4” hole, pull wires

through wall or panel.

2. Connect the ground wire from the vehicle and the

BLACK ground wire from the RoadTrip together,

using large yellow flag connector.

3. Connect the YELLOW flag connector to

the silver spade on the switch.

4. Connect the RED wire from the RoadTrip to the

small RED flag connector.

5. Connect small RED flag connector to center

spade on switch.

6. Connect the +12 V power wire from the vehicle to

a small RED flag connector.

7. Connect small RED flag connect to isolated

spade on switch.

INSTALLING THE POWER SWITCH DIAGRAM

STEPS 2 & 3

TWO GROUND WIRES

1 FROM VEHICLE

1 BLACK WIRE FROM

SATELLITE DISH STEPS 4 & 5

RED POWER

WIRE FROM

DISH

STEPS 6 &7

+12 V FROM VEHICLE

ON/OFF ROCKER SWITCH

WITH LIGHT

(Shown in OFF position.)

FIGURE 7

10. The GPS antenna is pre-wired and has a 1 meter

cable running through one of the connectors.

Determine location for GPS antenna. It is recom-

mended you place the GPS antenna 3 feet from

dome and away from any other obstruction.

The recommended location for the GPS antenna is

based on having a level location and a clear view of

the sky for the best satellite signal acquisition. Do not

secure GPS antenna to roof at this time.

IMPORTANT! The GPS must be located minimum of

3 feet away from obstructions on roof of vehicle. An-

tenna must have a clear view of the sky for proper

operation.

GPS installation — (RoadTrip SDi only)

!NICKS OR CUTS IN WIRING JACKET MAY

CAUSE WATER TO LEAK INTO VEHICLE.

COAX CABLE ROUTING

PRIMARY

RECEIVER

(GRAY WIRE)

MV-3500

ROADTRIP

FIGURE 2

SECONDARY

RECEIVER

(WHITE WIRE)

Connecting two receivers

1. Connect the gray coax cable coming from the

RoadTrip™ to the “SATELLITE IN” input on the

primary receiver. The primary receiver is the

receiver used most often and will toggle between

satellites.

2. Connect the white coax cable coming from the

RoadTrip™ to the “SATELLITE IN” input on the

secondary receiver. NOTE: Secondary receiver

will not toggle.

3. See page 5 of Operations Manual for receiver

set-up.

Installation • Wiring • Specifications

Connecting one receiver

1. Connect the coax cable from the gray coax

cable of the RoadTrip™ to the “SATELLITE IN” on

the receiver.

2. See page 5 of Operations Manual for receiver

set-up.

Connecting the receiver — Your RoadTrip™ has now been success-

fully installed. Proceed to the Operation

Manual for RoadTrip™ setup and for Op-

eration Instructions.

Features and specifications

• One button operation.

• Dual receiver capable.

• Depending on receiver type, you can access

satellites 119°, 110°, or 101°.

• No user input required.

• Elevation range 20° to 60°;

azimuth +360° (0-720°)

• Dome UV protected.

• Specifications for max amperage 5.0A

• Specifications for unit operatating voltage. -10.5 - 13.8V

• Specifications for supply voltage. 12 - 13.8V

• Compact size —

32” diameter, 12-1/2” height

Shipping size - 37-1/4” x 34” x 14-3/4”

Shipping weight - 55 lbs.

• Operating temperature

-13°F to +140°F

Winegard Company • 3000 Kirkwood Street • Burlington, IA 52601 • 319/754-0600 Fax 319/754-0787 • www.winegard.com

Andere Handbücher für RoadTrip SD

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Winegard Antenne Handbücher

Winegard

Winegard HD7078P Bedienungsanleitung

Winegard

Winegard RoadTrip SD Bedienungsanleitung

Winegard

Winegard In-Motion MVT-35W Bedienungsanleitung

Winegard

Winegard dish Playmaker Bedienungsanleitung

Winegard

Winegard HD7080P Bedienungsanleitung

Winegard

Winegard WX980 Bedienungsanleitung

Winegard

Winegard TRAV'LER Series Bedienungsanleitung

Winegard

Winegard MM-3084 Bedienungsanleitung

Winegard

Winegard HD-9095P Bedienungsanleitung

Winegard

Winegard Movin' View MV3500A Bedienungsanleitung

Winegard

Winegard HD-6010 Bedienungsanleitung

Winegard

Winegard FlatWave AIR Bedienungsanleitung

Winegard

Winegard HD-6000 Bedienungsanleitung

Winegard

Winegard Platinum Series/ Bedienungsanleitung

Winegard

Winegard TR-6100 Bedienungsanleitung

Winegard

Winegard RZ-6035 Bedienungsanleitung

Winegard

Winegard Trav'ler Bedienungsanleitung

Winegard

Winegard WV750 Bedienungsanleitung

Winegard

Winegard Movin' View MV3500T Bedienungsanleitung

Winegard

Winegard Movin' View MV-4002 Bedienungsanleitung

Winegard

Winegard TRAV'LER RP-SK01 Series Leitfaden

Winegard

Winegard RM-DM00 Bedienungsanleitung

Winegard

Winegard SENSAR Bedienungsanleitung

Winegard

Winegard RT8000T Bedienungsanleitung

Beliebte Antenne Handbücher anderer Marken

Alfa Network

Alfa Network APA-L01 Bedienungsanleitung

Naval

Naval PR-422CA Bedienungsanleitung

Feig Electronic

Feig Electronic ID ISC.ANTH200/200 Series Bedienungsanleitung

TERK Technologies

TERK Technologies TV44 Bedienungsanleitung

Directive Systems & Engineering

Directive Systems & Engineering DSE2324LYRMK Bedienungsanleitung

HP J8999A Bedienungsanleitung

MobilSat

MobilSat MSP-S Bedienungsanleitung

Steren

Steren ANT-UHF 13 Bedienungsanleitung

Novatel

Novatel 600-G Bedienungsanleitung

Radio Shack

Radio Shack Amplified VHF/UHF/FM Indoor Antenna Bedienungsanleitung

TRENDnet

TRENDnet TEW-AO12O Bedienungsanleitung

Radio Shack

Radio Shack 15-1837 Bedienungsanleitung

CommScope

CommScope CMAX-OMFX-43M-I53 Bedienungsanleitung

Ramsey Electronics

Ramsey Electronics DAP25 Bedienungsanleitung

COBHAM

COBHAM SAILOR 800 VSAT Gebrauchs- und Pflegehandbuch

Trango Systems

Trango Systems AD900-9 Bedienungsanleitung

Steren

Steren ANT-100 Bedienungsanleitung

Proxim

Proxim 5054-PA-23 Bedienungsanleitung