Winmate WM-OAP8251AG Bedienungsanleitung

Please read these instructions carefully before using this product, and save this manual for future use.

Outdoor Enterprise

Access Point

WM-OAP8251AG

Quick Start Guide

V1.0

For more information on this and other Winmate

products, please visit our website at:

www.winmate.com

Document Part Number: 91521110100L

FCC Statement

Federal Communication Commission Interference Statement

This equipment has been tested and found to comply with the

limits for a Class A digital device, pursuant to part 15 of the

FCC Rules. These limits are designed to provide reasonable

protection against harmful interference when the equipment is

operated in a commercial environment. This equipment

generates, uses, and can radiate radio frequency energy and,

if not installed and used in accordance with the instruction

manual, may cause harmful interference to radio

communications. Operation of this equipment in a residential

area is likely to cause harmful interference in which case the

user will be required to correct the interference at his own

expense.

FCC Caution: Any changes or modifications not expressly approved by the

party responsible for compliance could void the user’s authority to operate this

equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions: (1) This device may not cause harmful interference,

and (2) this device must accept any interference received, including interference

that may cause undesired operation.

For product available in the USA/Canada market, only channel 1~11

can be operated. Selection of other channels is not possible.

This device and its antennas (s) must not be co-located or operating in

conjunction with any other antenna or transmitter except in accordance with FCC

multi-transmitter product procedures.

IMPORTANT NOTE:

FCC Radiation Exposure Statement

This equipment complies with FCC radiation exposure limits set forth for an

uncontrolled environment. This equipment should be installed and operated with

minimum distance 25 cm between the radiator and your body.

Professional installation is required.

iii

WM-OAP8251AG Quick Start Guide

Contents

GETTING STARTED 1

Features 1

Package Contents 2

Minimum Requirements 2

Product Overview 3

INSTALLATION 5

Connecting the Access Point 5

Managed Access Point with Wireless Management Switch 5

Stand-alone Access Point Installation 6

Mounting 7

Wall Mounting the AP 7

Pole Mounting the AP 8

GETTING STARTED 10

Configuring Your Access Point 10

Default Settings 10

Web Configuration 10

WM-OAP8251AG Quick Start Guide

GETTING STARTED

Congratulations on purchasing Winmate® Outdoor Enterprise Access Point.

The WM-OAP8251AG is an enterprise class, outdoor dual radio 2.4G (11n) and 5G (11ac

Wave2) concurrent 4x4 MU-MIMO access point with built-in internal antenna. The device

has two Ethernet ports and one of it is a PSE port that supplies power to the remote unit.

With certified IP67 protection, Winmate® Outdoor Enterprise Access Point is designed to

deliver high reliability under harsh outdoor environment.

Features

Winmate® Outdoor Enterprise Access Point WM-OAP8251AG offers the following features:

Main Chip:

oProcessor: Qualcomm QCA8068B, dual core, 1.4GHz

oRadios 4x4 dual band dual concurrent

Radio 1: QCA9990B 4x4 to support 2.4GHz

Radio 2: QCA9990B 4x4 to support 5GHz

oEthernet PHY: AR8035B*1 + AR8033B*1 (Industrial graded components)

Available interface:

o2 x Gigabit Ethernet (RJ45)

o1 x Console (RJ45)

oLEDs

oGore vent for pressure equalization

oN-type connectors for external antenna model

IP67 compliance enclosure design

Ethernet surge protection support (4KV)

OAP8251AG can be powered with 802.3at+ (60W) Power Source on the 1st LAN

port (PD) and provide power to other device through the 2nd LAN port (PSE).

Max power consumption is < 55W when operating as OAP8251AG and providing

802.3af power on 2nd LAN

Pole mount and wall mount locking mechanism

Package Contents

Carefully remove the box and unpack your device. Please check if all the items listed

below are inside your package. If any of these items are missing or damaged contact us

immediately.

The factory shipment list:

Outdoor Enterprise

Access Point

WM-OAP8251AG

Quick Start Guide

(Hardcopy)

User Manual

EzMaster Software

& User Manual

PoE Injector

Wall Mounting Kit

Pole Mounting Kit

Mounting Screws

and Bolts

Ground Cable

(Green)

AWG10 180cm

Power Adapter

Power Cable

2.4GHz Detachable

Antennas x 4

5GHz Detachable

Antennas x 4

Minimum Requirements

Broadband Internet Service

(Cable or DSL Modem)

Internet Browser

(Internet Explorer, Safari, Firefox, Chrome, Edge)

WM-OAP8251AG Quick Start Guide

Product Overview

Unit dimensions (L x W x H): 210mm x 210mm x 51mm

Weight: 1.5 kg

Front View

No.

Description

2.4 GHz Antennas: Detachable 5 dBi 2.4 GHz omni-directional

5 GHz Antennas : Detachable 7 dBi 5 GHz omni-directional

LAN Port 1 (802.3at PoE Input): Ethernet port for RJ-45 cable.

LAN Port 2 (802.3af PSE Output): Ethernet port for RJ-45 cable.

Console/ Reset: Console panel/ reset button.

LED Indicators: LED lights for Power, LAN Port 1, LAN Port 2, 2.4 GHz

Connection and 5 GHz Connection.

Rear View

No.

Description

Ground

Mounting Holes: Using the provided mounting kits, the WM-OAP8251AG can

be attached to a wall or pole.

Optional M12 Connector

WM-OAP8251AG Quick Start Guide

INSTALLATION

Connecting the Access Point

Managed Access Point with Wireless Management Switch

This diagram depicts the hardware configuration.

Follow the instructions below to establish the connection to the Access Point.

A. Connect one end of the Ethernet Cable into the main LAN Port (PoE) of Managed

Access Point and the other end to the Ethernet Port on the Wireless Management

Switch.

B. Connect another Ethernet Cable into an Ethernet Port on the front panel of the

WM-OAP8251AG and the other end to the Ethernet Port on the computer.

C. Screw the provided antennas to the device as shown on the illustration below.

IMPORTANT:

The Access Point supports both IEEE 802.3at PoE (Power over Ethernet) and

the included power injector. You may use either one as the power source.

Do NOT use both at the same time.

Stand-alone Access Point Installation

Follow the instructions below to establish the connection to the Access Point.

A. Connect one end of the Ethernet Cable into the main LAN Port (PoE) of the Access

Point and the other end to the AP Ethernet Port.

B. Connect the Power Adapter to the DC-IN port of the PoE injector and plug the other

end into an electric outlet.

C. Connect the second Ethernet cable into the LAN port of the PoE injector and the other

end to the Ethernet port on the computer.

D. Screw on the provided antennas to the device as shown on the illustration below.

IMPORTANT:

The Access Point supports both IEEE 802.3at PoE (Power over Ethernet) and

the included power injector. You may use either one as the power source.

Do NOT use both at the same time.

WM-OAP8251AG Quick Start Guide

Mounting

Wall Mounting the AP

To attach the WM-OAP8251AG to a wall using wall mounting kit:

A. Mark the four locations of the mounting holes on the flat mounting surface.

B. Drill a 37 mm deep 8 mm hole in the markings and hammer the bolts into the openings.

C. Place the lock and flat washers on the four hex cap screws and drive the screws to

attach the bracket to the back of the Access Point.

Andere Handbücher für WM-OAP8251AG

Inhaltsverzeichnis

Andere Winmate Drahtloser Zugangspunkt Handbücher

Winmate

Winmate WM-OAP8251AG Bedienungsanleitung

Beliebte Drahtloser Zugangspunkt Handbücher anderer Marken

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Bedienungsanleitung

Ubiquiti

Ubiquiti NanoStation NSM2 Bedienungsanleitung

Cisco

Cisco Aironet 1550 Series Bedienungsanleitung

Aruba

Aruba IAP-335 Bedienungsanleitung

Advantek Networks

Advantek Networks AWN-AP-54MR Bedienungsanleitung

IP-COM

IP-COM AP355 Bedienungsanleitung

Buffalo

Buffalo AirStation WLA-L11G Bedienungsanleitung

EnGenius

EnGenius EnStationACv2 Bedienungsanleitung

D-Link

D-Link DAP-3662 Bedienungsanleitung

xG Technology

xG Technology xMax CN1300 Bedienungsanleitung

Widelink

Widelink ezWave WAP-1100 Series Bedienungsanleitung

Edimax

Edimax CAP1200 Bedienungsanleitung

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Bedienungsanleitung

Aruba

Aruba AP-203R Bedienungsanleitung

LuXout Shades

LuXout Shades LUXSHADE MOTION Bedienungsanleitung

CreatComm

CreatComm TB5F Bedienungsanleitung

SineDigital

SineDigital MW-1500AP(H) Bedienungsanleitung

TP-Link

TP-Link AP9650 V1 Bedienungsanleitung