Winplus JUMP STARTER PRO Bedienungsanleitung
User Manual
JUMP STARTER PRO
AC55717
2
Jump Starter
USB Cable and
Car Adaptor User Manual
PACKAGE CONTENTS:
Storage Case
Jumper Cable with
Safe & Smart Protection
3
TECHNICAL SPECIFICATIONS:
Power Button
Lantern Button
5V USB Charging Ports
5V USB Input Port
Jumper Cable Socket
Flash Mode Button
LED Spotlight
and Flashlight
Spotlight Button
Jumper Cable with Safe
& Smart Protection
Product Dimensions:
9.2 x 6.9 x 3.1 in (233 x 177 x 79 mm)
Product Weight: 2.425 lbs (1100g)
Internal Battery: Lithium-Ion
Capacity: Up to 12000 mAh (3.7V)
Input Voltage: 5V 2A/ 9V 1.7A via Car Adaptor
USB Output Voltage: 5V (2.4A + 2.1A)
Jump Start Current: 350A - 500A
Operating Temperature:
-4ºF ~ 104ºF (-20ºC ~ 40ºC)
Storage Temperature:
-4ºF ~ 104ºF (-20ºC ~ 40ºC) Avg. Temp.
Charging Temperature:
32ºF ~ 104ºF (0ºC ~ 40ºC)
Charging Time: 7-8 hours / 4-5 hours under 9V
Power
Indicator Lights
Hazard Light Button
Lantern
4
Press the power button to check the capacity of the Jump Starter.
When charging, the indicator lights will ash one by one. The
number of solid lights indicates the battery capacity. When all the
indicator lights are solid then the
Jump Starter
is fully charged.
Indicator Lights: 1 Flashing 1 Solid 2 Solid 3 Solid 4 Solid
Battery Capacity: Below 5% 5-25% 26-50% 51-76%
76% - Full
POWER LEVEL INDICATOR LIGHTS:
CHARGING THE JUMP STARTER:
At home:
1. Plug the USB cable into computer or any USB
2A wall adaptor (not included).
2. Connect the micro USB cable onto the
Jump Starter
.
In Car:
1. Plug the 9V 1.7A USB car adaptor
(included) into an available 12V socket.
2. Connect the micro USB cable onto
the
Jump Starter
.
NOTE: In order to
reduce the risk of re
or electric shock, an
adapter shall be chosen
that is suitable for
the application and is
certied as a Class 2
or LPS power supply or
power adapter.
NOTE: It is recommended to recharge the Jump Starter every
3-4 months to maintain the efciency and prolong the service life
of the internal battery even if the unit has not been used.
5
Use the original manufacturer’s USB cable that came with your
device and plug into one of the USB output ports. You can
charge two devices at the same time. One of the ports has a
maximum output of 2.4A while the other has a maximum output
of 2.1A. Press the power button once to begin charging your
device. The power level indicator will show the battery level and
turn off after 30 seconds.
To check the power capacity
again, simply press the power
button once.
Press the spotlight button once to turn
on the spotlight.
Press the spotlight button to turn off Spotlight.
Press the lantern button again to turn off.
CHARGING YOUR USB DEVICES:
LED SPOTLIGHT
Press the spotlight button a second time to
change the brightness level to 50%.
Press the lantern button once to turn on the
lantern light for full brightness.
LED LANTERN LIGHT
Press the lantern button a second time to
change the brightness level to 50%.
6
To jump start the 12-volt vehicle battery, put the
vehicle in park (neutral if the vehicle has a manual
transmission) and engage the emergency brake.
Locate the battery for the vehicle and follow the
steps listed below.
Jumper cables are color coded, RED for
POSITIVE (+) and BLACK for NEGATIVE (-).
DO NOT mix up the cables or allow the metal
ends to touch each other as this may damage the battery,
charging system and/or electronics on a vehicle.
1. Press the power button on the
Jump Starter
once and check
that the power level indicator is 3 solid lights (51%) or higher.
2. Take
the BLUE end of the
jumper cable and plug it into the
power bank jump start socket
which is located underneath the
black cover.
JUMP STARTING:
a) Press the ash button once for the
spotlight in front to ash. Press again for the
spotlight and lantern light to ash.
b) Press the hazard light button once to turn
on the hazard light.
LED FLASH MODE / HAZARD LIGHT
Black
Red
Black
Red
b
a
!
7
JUMP STARTING CONT.:
3. Connect the RED clamp to the POSITIVE (+) post on
the car battery. The POSITIVE battery post will be slightly
larger than the NEGATIVE post, and will be marked with a
PLUS (+) sign. There may also be a RED plastic protective
cover over the positive battery post.
4. Connect the BLACK clamp to the NEGATIVE (-) post
on the car battery. The NEGATIVE will be marked with
a MINUS (-) sign. There may also be a BLACK plastic
protective cover over the negative battery post.
NOTE: Do not connect the RED clamp (+) and the BLACK
clamp (-) at the same time. Connect the RED clamp rst, then
the BLACK clamp.
CAUTION: DO NOT lean directly over the battery while making
jumper connections.
5. Check the LED status on the indicator
light box located on the jumper cable.
Proceed to the next step unless the light
is ashing RED and BEEPING.
Please reference the LED status chart
on page 9 if needed.
Black
Red
Indicator Box
8
6. You now have 30 seconds to start your vehicle before the
jump starter times out to prevent the vehicle battery from
reverse charging the unit. If it does not crank or cranks very
slowly, wiggle the jumper connections to make sure they are
making good contact. Wait 60 seconds before trying to
start your car again. Each new jump start attempt requires
disconnection of both clamps from the car battery and
reconnection. The engine should start if there are no other
problems (such as a bad starter or ignition circuit problem).
Do not attempt to jump start the vehicle more than 3 times
with the Jump Starter. If the vehicle fails to start after 3
attempts, it is likely due to alternative reasons and should be
checked by an auto mechanic.
7. As soon as the engine starts, the indicator box on the BLACK
clamp will blink red and beep to let you know it is ok to
disconnect.
8. Please disconnect the jumper cables from your car within 30
seconds. First remove the RED/POSITIVE (+) clamp and
then the BLACK/NEGATIVE (-) clamp.
9.
Do not allow the metal ends of the jumper cables to touch each
other or the
RED
clamp to touch anything metal on the car.
Now unplug the
BLUE
end of the jumper cable from the
jump starter. This will reset the jumper cable. In 10
seconds the jump starter will power off automatically.
10. Keep the engine running for 20 to 30 minutes, or drive
the car to recharge the battery.
JUMP STARTING CONT.:
9
JUMP STARTING CONT.:
NOTE: If the engine dies shortly after it has been jump started, or
as soon as the jumper cables are disconnected, it probably means
the vehicle charging system is not working (bad alternator, voltage
regulator, wiring problem, or loose/dirty battery cables). Please seek
professional help from an auto mechanic to nd the root cause of the
problem.
The Jump Starter Pro may not work correctly for vehicles that require
remote battery jumper locations (e.g.: battery located in trunk or other
location). Please consult the owner’s manual for your vehicle.
Polarity Protection Circuit Status
Solid LED On Flashing LED LED Off
Status (Light & Sound Indicator)
Status Meaning:
Red Light Green Light Sound
None The car battery is ready for jump start.
None The Jump Starter needs to be charged.
None The car battery is ready for jump start. If
the indicator doesn’t turn solid Green, the
car battery voltage is higher than the jump
starter. You can still jump start your battery,
but may need to charge your jump starter.
Beeping Disconnect the jumper cable from the car
battery and jump starter. Either the car jump
start is complete or there is a connection
problem.
None This status shows after 30 seconds time out.
Disconnect the jumper cable from the car
battery and jump starter to reset. Reconnect
the jumper cable to jump start the vehicle.
None Please contact Winplus for troubleshooting.
10
• Always wear safety glasses when jump starting a battery (to protect
your eyes), and gloves when handling a battery (to protect your hands).
• When jump starting a vehicle please ensure that the blue plug is
securely tted into the jump start socket on the jump starter.
• Ensure the battery clamps are connected correctly, and the connectors
are free from rust and dirt.
• Do not allow this product to become wet. Exposure to excessive moisture
will damage the unit.
• Do not immerse the product in water.
• Do not operate the product in explosive atmospheres, such as in the
presence of ammable liquid, gas or dust.
• Do not modify or disassemble this product.
• Do not store in locations where the temperature may exceed 104ºF (40ºC).
• Charge only using the charger provided.
• Under extreme heat conditions, battery leakage may occur. Avoid contact
with your skin. In case of skin or eye contact, rinse immediately with
clean water and seek medical attention.
• If battery leakage occurs, take it to your local battery recycling center for
disposal. Do not attempt to use.
• Do not place the jump starter on the oor, or at a height less than 18
inches (457mm) above the oor, during use in a repair facility.
• This car jump starter is for use with 12V vehicles only. Using on non-12V
vehicles may cause serious damage to the vehicle, jump starter, or injury
to the user. Refer to the owner’s manual for the vehicle if you are
uncertain what voltage the vehicle runs on.
BATTERY DISPOSAL
The battery is self-contained and not consumer replaceable. The battery
must be disposed of properly when it no longer holds a charge. Proper
charging practices will increase the life of the product. For information on
battery recycling, call toll-free 800-822-8837.
For information regarding air travel safety with batteries please check the
U.S. Department of Transportation prior to travel at: http://phmsa.dot.gov/
safetravel/batteries
Note: The Jump Starter Pro contains the equivalent of 6.0g of lithium and
gives 44.4 watt hours of power.
INSTRUCTIONS PERTAINING TO RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS
WARNING:
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere Winplus Fernstartsystem Handbücher
