Wisdom Insight P7m-LCR Bedienungsanleitung

Owner’s Manual

Insight P7m-LCR

Insight P9m-LCR

LCR Planar Magnetic Soundbar Loudspeaker

INSIGHT P7m/P9m-LCR WISDOMAUDIO.COM

Table of Contents

Introduction | 3

Overview | 4

Unpacking and Installing the Insight P7m/P9m | 5

Mounting Options |6

Mounting the P7m/P9m on the Wall |6

Mounting the P7m/P9m To a TV Vesa Mount |8

Care & Maintenance | 21

North American Warranty | 21

Obtaining Service | 22

Specifications | 23

Dimensions | 24

DOCUMENT CONVENTIONS

This document contains general safety, installation, and operation instructions for the Wisdom

Audio Insight P7M/P9Mm Loudspeaker. It is important to read this document before attempting to

use this product. Pay particular attention to:

WARNING: Calls attention to a procedure, practice, condition or the like that, if not correctly

performed or adhered to, could result in injury or death.

CAUTION: Calls attention to a procedure, practice, condition or the like that, if not correctly

performed or adhered to, could result in damage to or destruction of part of or the entire product.

Note: Calls attention to information that aids in the installation or operation of the product.

INSIGHT P7m/P9m-LCR WISDOMAUDIO.COM

Introduction

Congratulations on purchasing your Wisdom Audio system. It incorporates many design features

engineered to give you decades of pleasure and performance. Many of these design choices are

uncommon among loudspeaker manufacturers and bear some explanation. See the following section

entitled “Overview” for more information.

The Insight Series P7m-LCR and P9m-LCR Soundbars are specifically designed to avoid the compromises

inherent in other conventional soundbar “custom length” designs, so you will not have to give up any

sound quality just to have it match the width of your TV.

The P7m-LCR Soundbar is available in custom lengths from a minimum width of 56.4” (1433mm) and a

maximum width of 70.4” (1788mm). The P7m-LCR contains (3) Spherical PMDs for the high frequencies

playing down to an amazing 900 Hz, and (4) 4.5″ Woofers to do the low-frequency heavy lifting.

The P9m-LCR is available in custom lengths from a minimum of 65.42″ (1661mm) and a maximum of

90.8″ (2306mm). It contains (3) Spherical PMDs for the high frequencies playing down to an amazing

900 Hz and (6) 4.5″ Woofers to do the low-frequency heavy lifting.

Your Insight P7m/P9m series loudspeaker are specifically designed to avoid the compromises inherent

in conventional speaker designs. Each P7m or P9m Series speakers is customized to fit the width of

your specific TV. Before ordering, contact Wisdom Audio Sales for specific details on sizes and

customization. [email protected]

INSIGHT P7m/P9m-LCR WISDOMAUDIO.COM

Overview

P9m-LCR Front View (Grille On)

P9m-LCR Front View (Grille Off) –Do Not Remove the Grille! The grille is an integral part of the

design; moreover, the planar magnetic film should never be touched, as it is tensioned precisely at the

factory. The grille plays an important protective role as well as an aesthetic one.

P7m-LCR Front View (Grille On)

P7m-LCR Front View (Grille Off) –Do Not Remove the Grille! The grille is an integral part of the design;

moreover, the planar magnetic film should never be touched, as it is tensioned precisely at the factory.

The grille plays an important protective role as well as an aesthetic one.

P7m-LCR and P9m-LCR Rear View Shown with Wall Mount Bracket

Removable Speaker

Wire Input Terminal

INSIGHT P7m/P9m-LCR WISDOMAUDIO.COM

Unpacking and Installing the P7m/P9m

The Wisdom Audio Insight P7m/P9m speaker is a substantial piece of equipment. Please exercise

caution when unpacking your P7M/P9Mm to ensure that you do not strain yourself from its (perhaps

unexpected) weight.

CAUTION: Do not attempt to lift your P7m/P9m while bending or twisting from the waist. Use your

legs for lifting, not your back. Always stand as straight as possible and keep the P7M/P9Mm close to

your body to reduce strain on your back.

With one person at each end, carefully lift the speaker out of the box and lay it on a soft surface

(carpet or similar).

After unpacking your P7m/P9m, keep all packing materials for future transport.

Making the P7m/P9m Connections

As with any system, you should make changes to the connections only when the power is turned off to

avoid any chance of inadvertently causing a problem (such as a short-circuit).

Three sets of speaker wires are required for each Insight P7m/P9m loudspeaker, one for each channel

of Left / Center / Right.

The connections are made on a removable 6-way connector (commonly called a “Phoenix” connector).

These will accept up to 12AWG (4.0mm2) wire. This removable terminal has small retainer tabs that

require 10 Ft-lbs (13.5Nm) to remove. It may be necessary to use a small tool to help remove the

terminal, but once inserted it should not come out easily.

Connect the outputs of your amplifier to the appropriate sections, taking care to get both the channel

assignments and the polarity correct. Connect the positive (+) terminals on the amplifier to the positive

(+) terminals on the loudspeaker; likewise, connect the negative (–) terminals on the amplifier and the

speaker, respectively.

Removable

Speaker Wire

Terminal

INSIGHT P7m/P9m-LCR WISDOMAUDIO.COM

Mounting Options for the P7m/P9m Series

There are 2 mounting options for the P7m/P9m Series. You must select one of these two options when

ordering the loudspeaker.

•WMA-IS - Insight Soundbar Wall Mount (any size) PN# 942100

•VESA-IS - Insight Soundbar Vesa TV Mount (any size) PN# 942200

Mounting the P7m/P9m on the Wall Using the WMA-IS

The Mounting bracket has slots that accommodate up to #10 (M5) Screws. It is recommended to place

a screw into every open mounting hole for maximum safety. Failure to use the proper screws and wall

attachment hardware may result in damage or injury.

Slots are arranged for 16” (406mm) On-center and 24” (610mm) On-center stud locations.

If you are not able to mount directly into a stud, use the appropriate masonry or dry-wall toggle bolts

that are rated for at least 25 lbs (10kg) each, and use at least 4 minimum, and 5 recommended (1 pair

per side plus the center).

•For a “zero clearance” installation, with the TV flush to the Soundbar, mount the Soundbar first

and the TV second to allow the TV to mount directly above the Soundbar.

•If mounting the Soundbar after the TV, you must allow for 0.45” (11.5mm) of clearance

between the TV and the Soundbar for the wall mount installation.

WMA-IS

Speaker Side Bracket

WMA-IS

Wall Side Bracket

Cut out for speaker

wire routing

INSIGHT P7m/P9m-LCR WISDOMAUDIO.COM

Please note that this guide assumes the wall surface is flat. If not, shims must be applied to the rear of

the mounting bracket so that the mounting bracket is uniformly secured to the wall and flat (not

distorted). The mounting steps are as follows:

1. Locate the area with the three sets speaker cables coming out of the wall.

2. Remove the screw down terminal from the speaker and pre-wire

the connector.

3. The wall bracket should have the tabs facing up. The slot in the

center is also the center of the speaker and should be used to

align the soundbar centered on the wall.

4. Using a bubble level to ensure that the mounting bracket is

plumb, mark screw holes for screws or toggle bolts, using the

bracket itself as your template. You can use any pair of slots for

mounting, plus the center in each end clip. Use both an upper

and a lower screw to ensure the bracket is stable.

5. Install screws suitable for the specific wall material (e.g.,

sheetrock, brick, concrete, etc.) in all the remaining holes in the

mounting bracket to ensure secure attachment to wall and avoid

any resonance from mounting bracket. Snug down the center

screw as well.

6. Attach the Speaker Side Bracket to the rear of the soundbar. The

4 mounting screws in the rear of the case will line up with the

mounting holes in the bracket. Make sure to tighten the screws.

7. Using assistance, while holding the speaker away from the wall,

connect the speaker terminal block until it clicks into place.

8. Slide the speaker from the top down onto the matching cleat.

The bracket will center the speaker once installed.

If you need to remove the speaker from the bracket for any reason, lift out from the bottom and then

up. Be sure to remove the speaker wire terminal before pulling away from the wall.

Important! Do not use the P7m/P9m as a shelf! While its mounting system is quite rugged, it is

designed to securely support the weight of the speaker itself. Do not place additional objects on it, and

do not climb on it.

INSIGHT P7m/P9m-LCR WISDOMAUDIO.COM

Mounting the P7m/P9m on the Wall Using the VESA-IS

The Vesa can be used with standard Vesa mount patterns on most TVs. The Vesa mount allows the

soundbar to be mounted to the TV for use with swivel and articulating mounts. Ensure that your TV can

handle the weight of the soundbar before attempting to attach it. The soundbar is not to be used as a

handle for moving the TV. Failure to use the proper screws and wall attachment hardware may result in

damage or injury.

Tools Needed:

•10mm Open end wrench

•6mm (M6) Hex Key

•#2 Phillips head screwdriver

Standard Vesa Mount Patterns include:

•400 mm x 400 mm (400 mm = 15.7 inches)

•600 mm x 400 mm (600 mm = 23.6 inches

•800 mm x 400 mm (800 mm = 31.5 inches)

Spider Plate

Vesa Rail

Slide Plate

INSIGHT P7m/P9m-LCR WISDOMAUDIO.COM

1. Prepare the wiring behind the TV:

a. Locate the area with the three sets speaker cables coming out of the wall.

b. Remove the screw down terminal from the speaker and pre-wire the connector. Run

the wire along the articulating mount with the other wires from the TV as needed.

2. Prepare the TV:

a. If the TV mount has already been attached to the TV, remove it temporarily.

b. If the TV mount has not been attached to the TV, find the TV mount hardware you will

use. The screws are usually M6 or M8 size Phillips head.

c. Make sure you follow the TV mount instructions correctly and use all the proper

hardware. Failure to do so could result in damage to the TV or injury to the user.

d. Place the TV face down on a suitable protective work surface where you can test fit the

speaker mount before placing on the wall, such as a moving blanket on the floor or

similar.

e. If the TV has an IR sensor or uneven surface on the bottom, use the included black

foam tape to take up the space. The Soundbar will mount up against this to remove any

visible space and make for a fully blacked out installation.

INSIGHT P7m/P9m-LCR WISDOMAUDIO.COM

3. Assemble the 2 Slide Plates to the Spider Plate using the included 10mm nuts. They are mirror

images of each other. At this time, they should only be finger tight. They will need to slide and

pivot for final adjustment.

Pivot point in the rear

Beliebte Sprecher Handbücher anderer Marken

argon audio

argon audio IE20 Bedienungsanleitung

Denon

Denon SC-N7 Bedienungsanleitung

Gemline

Gemline Ace 3952 Bedienungsanleitung

Focal

Focal ON WALL 300 Bedienungsanleitung

HEADRUSH

HEADRUSH Maximus HRSP 5024 Bedienungsanleitung

SoundLogic

SoundLogic BCCS-6/6395 Bedienungsanleitung

Peavey

Peavey DTH 218 Bedienungsanleitung

Avantree

Avantree Pluto Air Bedienungsanleitung

Morel

Morel Integra Series INTEGRA OVATION 4 Bedienungsanleitung

Oppo

Oppo SONICA Bedienungsanleitung

Bose

Bose SoundLink Wireless Music System Bedienungsanleitung

Rocksteady

Rocksteady Stadium Bedienungsanleitung

Bowers & Wilkins

Bowers & Wilkins 4 Bedienungsanleitung

Sonance

Sonance SONOS OUTDOOR Series Bedienungsanleitung

Electro-Voice

Electro-Voice EVID FM4.2 Bedienungsanleitung

Pioneer

Pioneer XW-HTD630 Bedienungsanleitung

Onn

Onn BWA16AA002 Bedienungsanleitung

HP GL313AA - USB Speakers PC Multimedia Bedienungsanleitung