Wisenet PNB-A9091RLPH Bedienungsanleitung

Wisenet Road AI

LPR Box Camera Kit

PNB-A9091RLPH

Quick Guide

view

OVERVIEW

INSTALLATION & CONNECTION

APPENDIX

Trademark

Each of trademarks herein is registered.The name of this product and other trademarks mentioned in this manual are the registered trademark of their

respective company.

Restriction

Copyright of this document is reserved. Under no circumstances, this document shall be reproduced, distributed or changed, partially or wholly, without

formal authorization.

Disclaimer

Hanwha Techwin makes the best to verify the integrity and correctness of the contents in this document, but no formal guarantee shall be

provided. Use of this document and the subsequent results shall be entirely on the user’s own responsibility. Hanwha Techwin reserves the

right to change the contents of this document without prior notice.

Design and specications are subject to change without prior notice.

Wisenet Road AI LPR Box

Camera Kit

Quick Guide

overview

CONTENTS

OVERVIEW

4 What’s Included

INSTALLATION & CONNECTION

5 Installation

3_ Contents

overview

4_ Overview

WHAT’S INCLUDED

Please check if your camera and accessories are all included in the product package. Each item may be package in its' own box.

Appearance Item Name Quantity

HOV32K2A700

OUTDOOR HOUSING

WBJA

WALL BRACKET

WITH BALL JOING

IRH30L

IR ILLUMINATOR

OSUPPIR

BRACKET FOR IR ILLUMINATOR

PNB-A90001LP

LPR BOX CAMERA WITH

32GB SD CARD

SLA-T-M1250DN

12-50mm LENS

Appearance Item Name Quantity

MOUNT CAP

MOUNT CAP fastener 1

M10 x L22 screw (to attach the install bracket)

M8 x L20 screw (to attach the housing)

M3 x L6 screw

(to attach the bracket adaptor and media convert) 4

M10 x L12 wrench bolt (to attach SBP-300WM/WMW) 4

M10 x L20 wrench bolt (to attach SBP-300WM1/WMW1) 4

M4 x L8 screw (to attach the media convert) 2

Quick Installation of housing, wall mount, and illuminator:

Fasten the plate (1) between the bottom of the housing (2)

and the bracket (3) using the supplied screws (4).

Fasten the top bracket (1) to the illuminator using the

screws and washers (2) supplied.

Fasten the illuminator and bracket using the nut and the

washer.

Set the vertical and horizontal angle, checking the resulting

illumination range on the screen. Tighten all the screws.

Twilight sensor activation threshold adjustment

The illuminator has an integrated twilight sensor that

allows its automatic activation and deactivation at

predefined luminous conditions.

The twilight sensor is set in the factory at a

predetermined luminous level, suitable for most

installations (approximately 50lx). If you want to

adjust the threshold, loosen the plug on the

illuminator rear and make adjustments with a

screwdriver.

By rotating the trimmer clockwise, the night mode

changeover occurs at a greater luminous value. By

rotating the trimmer counter-clockwise, the night mode

changeover is delayed to a lower luminous value.

Wait for appropriate brightness before switching on the

illuminator. Rotate the trimmer slowly until the LED on

the side of the trimmer switches on. Once the

intervention threshold has been surpassed (LED on),

rotate it slightly in the opposite direction.

Switch-on

threshould

regulator

Photocell

Power supply

and control

5_ Installation

Opening the housing

Loosen the 2 screws on the side of the housing, allowing

the cover and the upper half of the body to pivot open on

the hinge.

Slide removal

To remove the slide it is necessary to partially unscrew the

fixing screws as shown in the figure.

Move the slide by sliding it until the holes coincide with the

slide locking screws.

Installation of cable glands

Inside the supply are 3 cable glands that must be

installed at the bottom of the housing as shown in the

figure. The cable glands that are not used must be

sealed with a cap to avoid water entering the housing.

1.1.1 Ethernet cable installation

Insert the Ethernet cable in the gasket and block it as

shown in the figure.

Fit the gasket (1) to the cable gland M20 (2). Fasten the

cable gland to the bottom of the housing (3) using the

M20 nut.

Pay attentionto the fixing. Tightening torque: 7Nm.

Pass the cable with RJ45 connector (5) through the M20

cable gland (2). Tighten the cable gland cap (6).

How to install the camera

The correct operation of the equipment, within the

temperature range indicated, is guaranteed only if you use

a camera and lens with temperature limits equal to at least

-10°C and +60°C (14°F to 140°F)

Mount thecamera using the supplied screws (1) and

spacers (2).

Apply at least one spacer to guarantee electrical isolation

between the slide and the camera.

6_ Installation

Position the camera lens close to the glass to avoid visual

interference or optical reflections.

Connect the camera to the J2 connector (3) (PoE+ OUT)

Refit the slide in its housing and fix the previously

loosened screws.

Connection of the illuminator

Connect the illuminator to the J6 terminal as described

in the diagram below.

CONNECTION

THE

ILLUMINATOR

Illuminator

Terminal

Green

(telemetry)

Red

(telemetry)

White

(power supply)

Black (power supply)

7_ Installation

PoE+ cable connection

Connect the PoE+ cable from the Power Injector to the J1

connector.

Before powering the device, you must set the maximum

power consumption of the housing operating on dip switch

SW1, below.

Configuration

Before powering the device, you must set the

maximum power consumption of the housing to ON for

PoE+ class 4 (25.5W maximum output)

operating on dip

switch SW1. PoE+ is required due to the use of the

illuminator, defroster, & PoE+ camera.

POWER

CONSUMPTION

CONFIGURATION

SW1

Maximum

power

PoE+ Class 4 (25.5W max)

Switching on

The automatic pre-heating (De-Ice) process can start

whenever the device is switched on and the ambient

temperature is below 0°C (+32°F). The procedure is

necessary to guarantee correct operation of the devices

even at low temperatures.

The duration ranges depending on environmental conditions

(from 60 minutes up to 120 minutes).

During power on and boot up the device reads the status

of the dip switch and automatically detects all of the

connected options for the correct power management of

the housing.

The LEDs shown in the figure allow you to check the

product's operating status.

8_ Installation

The LEDs shown in the figure allow you to check the

product's operating status.

OPERATING

STATUS

LED

Status

Apparatus

Status

LD1 (Power

supply)

Off

The device is

not powered

The device is correctly powered

LD2

(Camera)

Off

The camera is not connected or

Cold Start is

active

The camera is correctly powered

flashing

The camera has a low identification

resistance

2 flashings

The camera has a high identifica

tion resistance

5 flashings

The camera has an excessive power

consumption

9 flashings

The camera requires more power

than the

available

LD3

(Demi

sting)

Off

Demisting was not correctly

detected

flashing

Standard demisting is inactive

2 flashings

The anti-ice system (optional) is

inactive

Demisting, or anti-ice system, is in

operation

LD4

(Heater)

Off

Heating is not available or power

available is

not sufficient

flashing

Heating is inactive

Heating is active

LD5

(Illumi

nator)

Off

The illuminator (optional) is not

detected or

the available power is

not sufficient

flashing The illuminator is correctly

powered

(illuminator activation is

controlled by the

photocell)

LD6

(Delayed

activation)

Off

Heating is

not available

flashing

The pre-heating procedure is

inactive

The pre-heating procedure is

underway

Procedure to assemble the camera with the lens.

Carefully insert the lens screw threads into the camera body

and fully tighten. Attach the lens iris cable into the camera

body connector. Adjust the lens zoom / focus levers. You

may need to perform a Focus Initialization to adjust the

sensor position after installation. Then perform a Simple

Focus.

Please consult the PNB-A9001 camera user manual and

Quick Guide for additional configuration steps that may

be necessary, such as configuring a password and IP

addressing.

The Wisenet Road AI application has been pre-installed

and licensed on the camera. Please consult the Wisenet

Road AI Quick Start Guide for more information on

getting started with using the LPR application.

9_Installation

PT01-004102A

Hanwha Techwin America

500 Frank W. Burr Blvd. Suite 43 Teaneck, NJ 07666

Toll Free +1.877.213.1222 Direct +1.201.325.6920

Fax +1.201.373.0124

www.hanwhasecurity.com

Inhaltsverzeichnis

Andere Wisenet Sicherheitskamera Handbücher

Wisenet

Wisenet QNP-6320H Bedienungsanleitung

Wisenet

Wisenet TNO-3040T Bedienungsanleitung

Wisenet

Wisenet TNO-6322ER Bedienungsanleitung

Wisenet

Wisenet QND-6011 Referenzhandbuch

Wisenet

Wisenet TNO-3010T Bedienungsanleitung

Wisenet

Wisenet XNV-9082R Bedienungsanleitung

Wisenet

Wisenet XNO-9082R Bedienungsanleitung

Wisenet

Wisenet LND-6012R Bedienungsanleitung

Wisenet

Wisenet PNM-9321VQP Bedienungsanleitung

Wisenet

Wisenet PNM-9000QB Bedienungsanleitung

Wisenet

Wisenet XNZ-L6320A Bedienungsanleitung

Wisenet

Wisenet HCP-6320H Bedienungsanleitung

Wisenet

Wisenet QNP-6320R Bedienungsanleitung

Wisenet

Wisenet SNF-8010 Bedienungsanleitung

Wisenet

Wisenet SLA-T4680DA Bedienungsanleitung

Wisenet

Wisenet TNO-X6072EPT1-Z Bedienungsanleitung

Wisenet

Wisenet XNV-6081 Bedienungsanleitung

Wisenet

Wisenet QND-7012R Bedienungsanleitung

Wisenet

Wisenet PNM-9322VQP Bedienungsanleitung

Wisenet

Wisenet SNV-6085 Bedienungsanleitung

Wisenet

Wisenet TNO-P9072EPT1-Z Bedienungsanleitung

Wisenet

Wisenet QNP-6230RH Bedienungsanleitung

Wisenet

Wisenet ANE-L7012R Bedienungsanleitung

Wisenet

Wisenet XND-L6080R Bedienungsanleitung

Beliebte Sicherheitskamera Handbücher anderer Marken

Okina USA

Okina USA SIR36-870VF650LP Bedienungsanleitung

Divio

Divio NDR155PA Bedienungsanleitung

Canon

Canon VB-C500D Bedienungsanleitung

Easy Access

Easy Access EasyGuard Bedienungsanleitung

Vivotek

Vivotek FD9389-EHV-v2 Bedienungsanleitung

TUYA

TUYA COSMO W2 Bedienungsanleitung

Eusso

Eusso UNC7500-IR Einrichtungshandbuch

urmet domus

urmet domus 1096/204 Bedienungsanleitung

VC VC20 series Bedienungsanleitung

Axis

Axis Q1614 Bedienungsanleitung

ieGeek

ieGeek DD201 Bedienungsanleitung

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Bedienungsanleitung

Vicon

Vicon V662-D-1 Betriebsanleitung

Grundig

Grundig GCH-K0274P Bedienungsanleitung

Lorex

Lorex VANTAGE LBC7032 Bedienungsanleitung

4xem

4xem WPT Bedienungsanleitung

Samsung

Samsung SCV-3082 Bedienungsanleitung

Vitek

Vitek VTC-C544 Bedienungsanleitung