Woo Audio WA6 Bedienungsanleitung

rightsreserved.

www.wooaudio.comRev1.0.June10,2011.1



WOO AUDIO WA6

Single-Ended Class-A Stereo Headphone Amplifier

Owner’s Manual

Please review this manual before operating your WOO AUDIO™ product.

rightsreserved.

www.wooaudio.comRev1.0.June10,2011.2



Important Safety Information

CAUTION: These amplifiers are shipped without the vacuum

tubes installed. It is necessary to install the tubes first. The tubes

must be installed correctly or serious damage that is not covered

by the warranty will result.

Turn off immediately in the event of malfunction

Should you notice smoke or an unusual smell coming from the

equipments, turn it off immediately. Continued operation could

result in injury.

Do not disassemble

High voltage circuit. Touching the product’s internal parts could

result in injury. In the event of malfunction, the product should be

repaired only by a qualified technician.

Keep out of children

Failure to observe this precaution could result in injury

WARNING: Failure to follow these instructions could result in

fire, electric shock, or other injury or damage.

rightsreserved.

www.wooaudio.comRev1.0.June10,2011.3



Table of Contents

IMPORTANT SAFETY INFORMATION 2

TABLE OF CONTENTS 3

OVERVIEW 4

QUICK INSTALLATION 5

OPERATION 9

COMPATIBLE TUBES 11

FAQ - FREQUENTLY ASKED QUESTIONS 12

WARRANTY AND SERVICE 13

REVIEWS 14

PRODUCT SPECIFICATION 15

rightsreserved.

www.wooaudio.comRev1.0.June10,2011.4



Overview

Thank you for choosing a Woo Audio product. The WA6 is finely hand-crafted amplifier

that delivers uncompromised performance and superior listening experience.

Point-to-Point wiring

One 5AR4 rectifier tube. Direct substitute: 5U4G

Two 6DE7 drive/power tubes

Pseudo-dual power supply

All tubes. No semi-conductors in the entire circuitry

High or low headphone impedance switch

One TRS ( ¼") headphone jack

80 watts specially made toroidal power transformer.

Full aluminum die-cast chassis, anodized finish

Whole aluminum volume knob and power switch button

Custom gold-plate RCA

Alps potentiometer and power switch

Dale and Vishay high precision resistors

Silver plated Teflon hook-up wires

rightsreserved.

www.wooaudio.comRev1.0.June10,2011.5



Quick Installation

What’s in the box?

①WA6 amplifier

②One 5AR4 rectifier tube

③One matched pair of 6DE7 power tubes

The actual tubes may look different.

Compatible tubes may be included instead of the ones illustrated above.

Power cord and interconnection cable are not included.

rightsreserved.

www.wooaudio.comRev1.0.June10,2011.6



Installing the rectifier tube:

Note: avoid oil or smudge on the tube glass; clean hands before installation.

1. Find the correct tube for the socket. There is a label below each tube socket that

indicates a standard tube for the amplifier. For example, a 5AR4 tube should

install on the socket labeled “5AR4”. You MUST use the compatible tube or

serious damage may occur to the amplifier. See Compatible Tube section for all

the approved direct substitute tubes.

2. Align the tube guide pin to the socket as below.

3. Hold the tube base firmly then squeeze it into the socket slowly. Be sure to apply

force perpendicular to the tube socket; never insert the tube at an angle. Apply

slight rocking motion for the tube, which is harder to insert; never apply circular

motion. Apply pressure from top of the tube if needed.

Tube socket guide pin indicator

Guide pin shows on the

bottom of a tube.

Do no insert a tube at an angle

Insert a tube perpendicular to

the socket.

Hold base firmly.





rightsreserved.

www.wooaudio.comRev1.0.June10,2011.7



4. Check installation. The tube pins should be inserted fully into the tube socket

receptacles.

Installing the driver/power tubes:

Selecting AC voltage:

WARNING: failure to select the correct voltage will result in damage of the amp.





Switch to label “115” for

AC100 to 125V voltage.

Switch to label “230” for

AC210 to 240V voltage.

Insert the tube perpendicular

to the socket

Use both hands if needed

Bottom of the tube

Align the 6DE7 to the socket

rightsreserved.

www.wooaudio.comRev1.0.June10,2011.8



Installing the power cord:

Plug the power cord into the AC inlet. See ②in the below diagram. The AC inlet socket is a

standard IEC type. You will need to obtain the correct type for your region.

Installing the source input:

Plug the RCA interconnection cable into the RCA connectors ③.

Back panel diagram:



①Voltage selection switch

②AC inlet

③Impedance selector

④RCA input

U.S.

European

U.K.

rightsreserved.

www.wooaudio.comRev1.0.June10,2011.9



Operation

DO NOT

oTurn on the amp before properly installing ALL tubes.

oUse tubes that are not approved by Woo Audio.

oTurn on the equipment without checking the correct AC voltage setting.

oRemove any tubes or the DC cord while the amp is operating

oTouch tubes (extremely hot) after warm-up.

oLeave the amps running unattended. To use the amps safely, please allow it to

cool down for every 8 hours of continuous play time.

oPlace the amp away from any wireless or frequency-emitting devices such as

mobile phones, PDAs and radios, to avoid noise interference.

oKeep away from water or excessive moisture.

oTurn off the amp if its sound is abnormal.

oAllow a minimum of 2 inches of air clearance for heat dissipation.

oAllow approximately 5 minutes of warm-up.

oAllow the tubes to cool down before replacing them.

rightsreserved.

www.wooaudio.comRev1.0.June10,2011.10



Turning the amplifier on:

1. Turn the volume knob to the lowest position.

2. Insert a headphone into headphone output ①.

3. Press the power switch ③to a locking position. The power LED will light.

4. Observe that all tubes light gradually.

5. Let the tubes warm up for at least 1 minute before turning up the volume.

Front panel diagram:

①Headphone output

②Volume control

③Power switch

④PowerLED indicator

Break-in period:

It is recommended to allow the amplifier to operate 150+ hours so that peak performance can be

realized. An effective way to break-in the amp is to run the amp normally with music playing.

Please do not leave the amp running continuously.

Inhaltsverzeichnis

Andere Woo Audio Verstärker Handbücher

Woo Audio

Woo Audio WA7 Fireflies Bedienungsanleitung

Woo Audio

Woo Audio WA7 Fireflies Bedienungsanleitung

Woo Audio

Woo Audio WA5 Bedienungsanleitung

Woo Audio

Woo Audio WA23 LUNA Bedienungsanleitung

Woo Audio

Woo Audio WES Bedienungsanleitung

Woo Audio

Woo Audio WA6-SE Bedienungsanleitung

Woo Audio

Woo Audio WA5 Bedienungsanleitung

Woo Audio

Woo Audio WA-5 300B Bedienungsanleitung

Woo Audio

Woo Audio WA3 Bedienungsanleitung

Woo Audio

Woo Audio WA11 topaz Bedienungsanleitung

Woo Audio

Woo Audio WA7d Bedienungsanleitung

Woo Audio

Woo Audio WA22 Bedienungsanleitung

Woo Audio

Woo Audio WA2 Bedienungsanleitung

Beliebte Verstärker Handbücher anderer Marken

ASTRO

ASTRO HVO V40 P Bedienungsanleitung

Marantz

Marantz SUPERSCOPE BLA-545 Montageanleitung

NAD

NAD CI980 Bedienungsanleitung

Technics

Technics SE-CH770 Bedienungsanleitung

Harman Kardon

Harman Kardon HK6300 Bedienungsanleitung

NAD

NAD T975 Bedienungsanleitung

McIntosh

McIntosh MA6850 Bedienungsanleitung

Electro-Harmonix

Electro-Harmonix ENGLISH MUFF’N Bedienungsanleitung

Viatron

Viatron Autrix Bedienungsanleitung

GME

GME GA9800 Bedienungsanleitung

Atlas

Atlas CP700 Bedienungsanleitung

Roland

Roland KC-1000 Bedienungsanleitung

Pyle

Pyle PFMRA350BW Bedienungsanleitung

Advantage

Advantage S-250 Bedienungsanleitung

IRT Electronics

IRT Electronics DVA-3007 Bedienungsanleitung

Dimavery

Dimavery BA-100 Series Bedienungsanleitung

Sony

Sony XM-S400D Bedienungsanleitung

Schertler

Schertler ROY X Bedienungsanleitung