woodmizer EG200 Leitfaden
Twin Blade Edger
Safety, Operation& Maintenance Manual
EG200G26 rev. B2.03
EG200D24 rev. B2.03
EG200EC15 rev. B2.03
Safety is our #1 concern! Read and understand
all safety information and instructions before oper-
ating, setting up or maintaining this machine.
Form #904
©2019
Printed in the United States of America, all rights reserved. No part of this manual may be
reproduced in any form by any photographic, electronic, mechanical or other means or
used in any information storage and retrieval system without written permission from
Wood-Mizer
8180 West 10th Street
Indianapolis, Indiana 46214
&DOLIRUQLD
3URSRVLWLRQ:DUQLQJ
:$51,1*%UHDWKLQJJDVGLHVHOHQJLQHH[KDXVWH[SRVHV\RXWRFKHPLFDOVNQRZQWR
WKH6WDWHRI&DOLIRUQLDWRFDXVHFDQFHUDQGELUWKGHIHFWVRURWKHUUHSURGXFWLYHKDUP
$OZD\VVWDUWDQGRSHUDWHWKHHQJLQHLQDZHOOYHQWLODWHGDUHD
,ILQDQHQFORVHGDUHDYHQWWKHH[KDXVWWRWKHRXWVLGH
'RQRWPRGLI\RUWDPSHUZLWKWKHH[KDXVWV\VWHP
'RQRWLGOHWKHHQJLQHH[FHSWDVQHFHVVDU\
)RUPRUHLQIRUPDWLRQJRWRZZZ3ZDUQLQJVFDJRY
:$51,1*'ULOOLQJVDZLQJVDQGLQJRUPDFKLQLQJZRRGSURGXFWVFDQH[SRVH\RXWR
ZRRGGXVWDVXEVWDQFHNQRZQWRWKH6WDWHRI&DOLIRUQLDWRFDXVHFDQFHU$YRLGLQKDOLQJ
ZRRGGXVWRUXVHDGXVWPDVNRURWKHUVDIHJXDUGVIRUSHUVRQDOSURWHFWLRQ
)RUPRUHLQIRUPDWLRQJRWRZZZ3:DUQLQJVFDJRYZRRG
Table of Contents Section-Page
Table of Contents EGdoc072519 iii
Table of Contents Section-Page
iv EGdoc072519 Table of Contents
ABOUT THIS MANUAL V
SECTION 1 SAFETY 1-1
1.1 Safety Symbols.......................................................................................1-1
1.2 Safety Instructions..................................................................................1-2
SECTION 2 SERVICING THE EDGER 2-1
2.1 If You Need To Order Parts ...................................................................2-1
2.2 Customer and Edger Identification.........................................................2-2
2.3 If You Need Service ...............................................................................2-4
SECTION 3 EDGER SETUP 3-1
3.1 Setting Up the Edger ..............................................................................3-1
3.2 Electrical Installation (EE15 Only) ........................................................3-3
3.3 Pre-Operation Check ..............................................................................3-4
3.4 Edging Lumber.......................................................................................3-6
3.5 Preparing the Edger for Towing...........................................................3-11
SECTION 4 MAINTENANCE 4-1
4.1 Changing the Blades...............................................................................4-1
4.2 Tensioning the Belts...............................................................................4-5
4.3 Tensioning the Chains ............................................................................4-8
4.4 Checking the Rollers ..............................................................................4-9
4.5 Lubrication ...........................................................................................4-10
4.6 Feed Rate..............................................................................................4-11
4.7 Maintaining and Sharpening Anti-Kickback Fingers...........................4-12
4.8 Alignment .............................................................................................4-13
SECTION 5 TROUBLESHOOTING 5-1
5.1 Boards Are Not Self-Feeding .................................................................5-1
5.2 Jammed Boards ......................................................................................5-2
INDEX I
EGdoc072519 v
ABOUT THIS MANUAL
This manual is to replace or to be used with all previous information received on the
Wood-Mizer® * EG200 Twin Blade Edger. All future mailings will be an addition to or a revi-
sion of individual sections of this manual as we obtain new information.
The information and instructions given in this manual do not amend or extend the limited
warranties for the equipment given at the time of purchase.
*Wood-Mizer® is a registered trademark of Wood-Mizer Products, Inc.
Setworks Dial
Fuel Tank
Power Supply
Gearbox Housing
Blade Housing
Outfeed Table/Feed Rollers
Infeed Table/Feed Rollers
TB0001
Front Guide Fence
Anti-kickback
Release Lever
Press Rollers
Feed Return Rollers
Adjustable Outriggers
Retractable Hitch
Emergency Stop
Safety
Safety Symbols
1
1-1 EGdoc072519 Safety
SECTION 1 SAFETY
1.1 Safety Symbols
The following symbols and signal words call your attention to instructions concerning your
personal safety. Be sure to observe and follow these instructions.
DANGER! indicates an imminently hazardous situation
which, if not avoided, will result in death or serious injury.
WARNING! suggests a potentially hazardous situation
which, if not avoided, could result in death or serious injury.
CAUTION! refers to potentially hazardous situations which,
if not avoided, may result in minor or moderate injury or
damage to equipment.
IMPORTANT! indicates vital information.
NOTE: gives helpful information.
Warning stripes are placed on areas where a single decal
would be insufficient. To avoid serious injury, keep out of
the path of any equipment marked with warning stripes.
Servicing The Edger
Safety Instructions
Servicing The Edger EGdoc072519 1-2
1
1.2 Safety Instructions
NOTE: ONLY safety instructions regarding personal injury are listed in this section. Cau-
tion statements regarding only equipment damage appear where applicable throughout
the manual.
WARNING! Clean sawdust from all guards, vents, con-
trol boxes, or any area where sawdust may gather after
every shift. Failure to do so may result in fire, causing
death or serious injury.
OBSERVE SAFETY INSTRUCTIONS
IMPORTANT! Read the entire Owner's Manual before operating
the Edger. Take notice of all safety warnings throughout this man-
ual and those posted on the machine. Keep this manual with this
machine at all times, regardless of ownership.
Also read any additional manufacturer’s manuals and observe any
applicable safety instructions including dangers, warnings, and
cautions.
Only persons who have read and understood the entire operator's
manual should operate the Edger. The Edger is not intended for
use by or around children.
IMPORTANT! It is always the
owner's responsibility to comply
with all applicable federal, state
and local laws, rules and regula-
tions regarding the ownership,
operation and towing of your
Wood-Mizer Edger. All
Wood-Mizer owners are encour-
aged to become thoroughly
familiar with these applicable
laws and comply with them fully while using or towing the Edger.
WEAR SAFETY CLOTHING
WARNING! Secure all loose clothing and jewelry before operating
the Edger. Failure to do so may result in serious injury or death.
Servicing The Edger
Safety Instructions
1
1-3 EGdoc072519 Servicing The Edger
WARNING! Always wear eye, ear, respiration,
and foot protection when operating or servicing
the Edger.
DISPOSE OF SAWING BY-PRODUCTS PROPERLY
WARNING! Maintain a clean and clear path for all necessary
movement around the Edger and lumber stacking areas. Failure to
do so will result in serious injury.
IMPORTANT! Always properly dispose of all sawing by-products,
including sawdust and other debris, coolant, oil, fuel, oil filters and
fuel filters.
USE CAUTION WHEN WORKING WITH BATTERIES
DANGER! Batteries expel explosive gases. Keep sparks, flames,
burning cigarettes, or other ignition sources away at all times.
Always wear safety goggles and a face shield when working near
batteries. Failure to do so will cause serious injury.
WARNING! Battery posts, terminals and related accessories con-
tain lead and lead compounds, chemicals known to the State of
California to cause cancer and reproductive harm. Wash hands
after handling.
WARNING! Charge the battery in a well ventilated area. Do not
attempt to charge a frozen battery.
CAUTION! Do not overcharge the battery. Overcharging may
reduce the overall service life of the battery.
CAUTION! Be sure the battery is fully charged before transporting
the edger. If the battery is not fully charged, excessive vibration
could reduce the overall service life of the battery.
HANDLE FUEL/LUBRICANTS SAFELY
DANGER! Due to the flammable nature of fuel and oil, never
smoke, weld, grind or allow sparks near your engine or storage
tanks, especially during times of fueling.
DANGER! Never allow fuel to spill on a hot engine during fueling
operations or otherwise. The hot temperature of your engine could
Servicing The Edger
Safety Instructions
Servicing The Edger EGdoc072519 1-4
1
induce a fire or explosion.
WARNING! Store gasoline away from saw-
dust and other flammable materials. Failure
to do so may result in serious injury.
CHECK EDGER BEFORE OPERATION OR TOW-
ING
DANGER! Make sure all guards
and covers are in place and
secured before operating or tow-
ing the Edger. Failure to do so
may result in serious injury.
WARNING! Also make sure
your hitch has adequate safety
chain hookups. Safety chains
should be hooked to bumper of vehicle so that each chain would
pull the trailer equally in the event the hitch became disengaged.
Failure to do so may result in serious personal injury and/or severe
machine damage
WARNING! Always shut off the engine to stop the blade whenever
the Edger is not in use. Failure to do so may result in serious injury.
WARNING! Do not for any reason adjust the engine drive belts
with the engine running. Doing so may result in serious injury.
WARNING! Always ensure that there is a sharp point on the
anti-kickback fingers before each use of the Edger.
Be sure anti-kickback fingers are free from obstruction and are in a
downward position with lever released. Failure to do so may result
in serious injury.
KEEP PERSONS AWAY
DANGER! Keep all persons out of the path of moving equipment
and boards when operating the Edger. Failure to do so will result in
serious injury.
KEEP HANDS AWAY
Servicing The Edger
Safety Instructions
1
1-5 EGdoc072519 Servicing The Edger
DANGER! Engine components can become very hot during opera-
tion. Avoid contact with any part of a hot engine. The exhaust com-
ponents of your engine are especially hot during and following
operation. Contact with hot engine components can cause serious
burns. Therefore, never touch or perform service functions on a hot
engine. Allow the engine to cool sufficiently before beginning any
service function.
DANGER! Moving Parts Can Crush and Cut. Keep hands clear.
Make sure all guards and covers are in place and secured before
operating or towing. Failure to do so may result in serious injury.
DANGER! Always be aware of and
take proper protective measures
against rotating shafts, pulleys, fans,
etc. Always stay a safe distance from
rotating members and make sure that
loose clothing or long hair does not
engage rotating members resulting in
possible injury.
Inhaltsverzeichnis
Andere woodmizer Gesehen Handbücher
woodmizer
woodmizer LT10 Bedienungsanleitung
woodmizer
woodmizer 1982 LT30 Bedienungsanleitung
woodmizer
woodmizer LX50 EH7S Bedienungsanleitung
woodmizer
woodmizer LT40 MH Series Leitfaden
woodmizer
woodmizer LT60 Bedienungsanleitung
woodmizer
woodmizer LT15 S2-4 E11S Bedienungsanleitung
woodmizer
woodmizer PD200G Series Leitfaden
woodmizer
woodmizer LT15 AL-KO Bedienungsanleitung
woodmizer
woodmizer LX450-RA Bedienungsanleitung
woodmizer
woodmizer Autoclutch Option Bedienungsanleitung
woodmizer
woodmizer LT30HD Bedienungsanleitung
woodmizer
woodmizer G15 Leitfaden
woodmizer
woodmizer Cookie-Mizer 2510 Bedienungsanleitung
woodmizer
woodmizer SHR-T Series Bedienungsanleitung
woodmizer
woodmizer LT20L AH Bedienungsanleitung
woodmizer
woodmizer LT25 Bedienungsanleitung
woodmizer
woodmizer LT20 Series Bedienungsanleitung
woodmizer
woodmizer LX55 Leitfaden
woodmizer
woodmizer HR500 Leitfaden
woodmizer
woodmizer LX150 Leitfaden
