woodmizer LX450DB-A Bedienungsanleitung
Debarker Option
Safety, Installation, Operation,
Maintenance & Parts Manual
LX450DB-A rev. C
Safety is our #1 concern! Read and understand
all safety information and instructions before oper-
ating, setting up or maintaining this machine.
October 2017
Form #2298
Used with all LX450 mill rev. A1.00 - A1.05
©2019
Printed in the United States of America, all rights reserved. No part of this manual may be
reproduced in any form by any photographic, electronic, mechanical or other means or used in
any information storage and retrieval system without written permission from
Wood-Mizer
8180 West 10th Street
Indianapolis, Indiana 46214
&DOLIRUQLD
3URSRVLWLRQ:DUQLQJ
:$51,1*%UHDWKLQJJDVGLHVHOHQJLQHH[KDXVWH[SRVHV\RXWRFKHPLFDOVNQRZQWR
WKH6WDWHRI&DOLIRUQLDWRFDXVHFDQFHUDQGELUWKGHIHFWVRURWKHUUHSURGXFWLYHKDUP
$OZD\VVWDUWDQGRSHUDWHWKHHQJLQHLQDZHOOYHQWLODWHGDUHD
,ILQDQHQFORVHGDUHDYHQWWKHH[KDXVWWRWKHRXWVLGH
'RQRWPRGLI\RUWDPSHUZLWKWKHH[KDXVWV\VWHP
'RQRWLGOHWKHHQJLQHH[FHSWDVQHFHVVDU\
)RUPRUHLQIRUPDWLRQJRWRZZZ3ZDUQLQJVFDJRY
:$51,1*'ULOOLQJVDZLQJVDQGLQJRUPDFKLQLQJZRRGSURGXFWVFDQH[SRVH\RXWR
ZRRGGXVWDVXEVWDQFHNQRZQWRWKH6WDWHRI&DOLIRUQLDWRFDXVHFDQFHU$YRLGLQKDOLQJ
ZRRGGXVWRUXVHDGXVWPDVNRURWKHUVDIHJXDUGVIRUSHUVRQDOSURWHFWLRQ
)RUPRUHLQIRUPDWLRQJRWRZZZ3:DUQLQJVFDJRYZRRG
Table of Contents Section-Page
Table of Contents LX450DB17doc072219 iii
SECTION 1 SAFETY 1-1
1.1 Installation and Maintenance..................................................................1-1
1.2 Operation and Towing............................................................................1-2
SECTION 2 DEBARKER INSTALLATION 2-1
2.1 Debarker Installation ..............................................................................2-1
2.2 Harness Installation ................................................................................2-5
2.3 Control Component Installation .............................................................2-8
SECTION 3 ALIGNMENT 3-1
SECTION 4 OPERATION AND MAINTENANCE 4-1
4.1 Locking Pin Operation ...........................................................................4-1
4.2 Control Overview ...................................................................................4-2
4.3 Operation ................................................................................................4-3
4.4 Maintenance ...........................................................................................4-5
4.5 Troubleshooting......................................................................................4-6
SECTION 5 ELECTRICAL INFORMATION 5-1
5.1 Electrical Component List......................................................................5-1
5.2 Electrical Wiring Diagram .....................................................................5-2
SECTION 6 DEBARKER PARTS 6-1
6.1 Mechanical Assembly ............................................................................6-1
6.2 Frame Assembly.....................................................................................6-2
6.3 Debarker Mount Arm Assembly ............................................................6-4
6.4 Debarker Pivot Arm Assembly ..............................................................6-6
6.5 Debarker Cutter Head Assembly............................................................6-7
6.6 Debarker Upper Pivot Assembly............................................................6-9
6.7 Control Kit............................................................................................6-11
INDEX I
Safety
Installation and Maintenance
1
1-1 DB17doc072219 Safety
SECTION 1 SAFETY
This symbol calls your attention to instructions concerning your personal safety. Be sure
to observe and follow these instructions. This symbol accompanies a signal word. The
word DANGER indicates an imminently hazardous situation which, if not avoided, will
result in death or serious injury. WARNING suggests a potentially hazardous situation
which, if not avoided, could result in death or serious injury. CAUTION refers to potentially
hazardous situations which, if not avoided, may result in minor or moderate injury to per-
sons or equipment. Read all safety instructions before operating this equipment and
observe all safety warnings!
1.1 Installation and Maintenance
DANGER! On electric mills, hazardous voltage inside the
disconnect box, starter box, and at the electric motor can
cause shock, burns, or death. Disconnect and lock out
power supply before performing debarker installation! Fol-
low all applicable electrical codes.
DANGER! Make sure all electrical installation, service
and/or maintenance work is performed by a qualified elec-
trician and is in accordance with applicable electrical codes.
Failure to do so will result in serious injury or death.
DANGER! Before performing any service to this equip-
ment, turn the key to the OFF position, remove the key, and
disconnect the sawmill battery ground terminal. Failure to
do so will result in serious injury or death.
WARNING! Before replacing the debarker blade, move the
sawmill blade guide arm in front of the sawmill blade to
cover the blade teeth. Failure to do so may result in serious
injury or death.
Safety
Operation and Towing
Safety DB17doc072219 1-2
1
1.2 Operation and Towing
DANGER! Make sure all guards and covers are in place
and secured before operating the debarker option. Failure
to do so may result in serious injury.
DANGER! Keep all persons out of the path of moving
equipment when operating the debarker. Failure to do so
will result in serious injury.
DANGER! Always remove the key from the control panel
before preparing the debarker for towing. Failure to do so
may result in serious injury.
WARNING! Debarker is ON when warning light is on. DO
NOT disconnect the warning light. Doing so may result in
serious injury.
WARNING! If the debarker continues to run with the key
switch in the OFF position, remove the negative battery ter-
minal from the battery post.
DO NOT continue to operate the mill if the main key switch
does not control debarker operation. Doing so could result
in serious injury. Call Wood-Mizer customer service for
more information.
Debarker Installation
Debarker Installation
2
2-1 DB17doc072219 Debarker Installation
SECTION 2 DEBARKER INSTALLATION
DANGER! On electric mills, hazardous voltage inside the
disconnect box, starter box, and at the electric motor can
cause shock, burns, or death. Disconnect and lock out
power supply before performing debarker installation! Fol-
low all applicable electrical codes.
DANGER! Before performing any service to this equip-
ment, turn the key to the OFF (0) position, remove the key,
and disconnect the sawmill battery ground terminal. Failure
to do so will result in serious injury or death.
CAUTION! Due to various design changes and past retro-
fits and options, you should very carefully look your mill
over to determine Debarker compatibility before beginning
Debarker installation.
2.1 Debarker Installation
DANGER! Always disengage the blade and shut off the
sawmill engine before installing the debarker. Failure to do
so will result in serious injury.
IMPORTANT! Sawmills are equipped with pre-drilled
Debarker mounting holes. Verify hole locations before
beginning Debarker installation. Proper hole location is
imperative for safe and effective Debarker operation.
1. Open the blade housing cover.
Debarker Installation
Debarker Installation
Debarker Installation DB17doc072219 2-2
2
2. Assemble the debarker to the sawmill saw head. Align the mounting block holes and the
two debarker mounting holes in the saw head. Use the provided hex head bolts, split lock
and flat washers to secure in place. Make sure the debarker is square to the saw head
before tightening.
See Figure 2-1.
FIG. 2-1
LX0042-1
Debarker Frame
Assembly
Washer, ½
Split Lock (4)
Washer, ½
Flat (4)
Bolt, 1/2-13x3
Hex Head (4)
Debarker Installation
Debarker Installation
2
2-3 DB17doc072219 Debarker Installation
3. Assemble the debarker cutting head to the mount plate on the frame.
Use the four provided bolts and split lock washers to mount the cutting head to the
debarker frame. Use the lower set of four holes in the head mounting plate. The upper set
of holes are provided in the event the cutting head needs to be adjusted further down
than the slotted motor mount holes will allow.
See Figure 2-2.
FIG. 2-2
LX0042-2
5/16-18 x 3/4"
Hex Head Bolts (4)
5/16" Lock Washers (4)
Cutting Head
Debarker Installation
Debarker Installation
Debarker Installation DB17doc072219 2-4
2
4. Install the blade guard bracket and flexible debris guard to the debarker head with two flat
washers, lock washers, and hex head bolts. Be sure the bottom of the debris guard is
even with the bottom of the debarker blade.
See Figure 2-3.
FIG. 2-3
LX0042-3
Debris
Guard
Guard
Bracket
1/4-20 x 1" Hex
head bolt (2)
1/4" Lock
washer (2)
1/4" Flat
washer (2)
Adjust bottom of debris guard
even with bottom of debarker blade
Debarker Installation
Harness Installation
2
2-5 DB17doc072219 Debarker Installation
2.2 Harness Installation
DANGER! Before performing any service to this equip-
ment, turn the key to the OFF (0) position, remove the key,
and disconnect the sawmill battery ground terminal. Failure
to do so will result in serious injury or death.
IMPORTANT! Avoid pinch and pivot points, unnecessary
wire bending and open spaces where the wire could get
caught by a log, etc. If you have any questions, call
Wood-Mizer customer service.
1. Route the harnesses through the saw head frame hole as shown. Continue routing the
long blade motor wire harness (large wires/ring terminals) inside the debarker frame
through the three holes with grommets.
See Figure 2-4.
FIG. 2-4
+
-
Blade
Motor
Wires
Warning Light
Wires
Connect In/Out
Motor Cable
To Debarker
Harness
Install Ring Terminals
To Warning Light Wires.
Install Boots Over
Light And Motor Wires
And Connect To Debarker
Blade Motor
Red/+, Black/-).
LX0042-4B
Inhaltsverzeichnis
Andere woodmizer Gesehen Handbücher
woodmizer
woodmizer LT50HD Bedienungsanleitung
woodmizer
woodmizer LX150 Leitfaden
woodmizer
woodmizer LX100 SW-10 Bedienungsanleitung
woodmizer
woodmizer SHR-T Series Bedienungsanleitung
woodmizer
woodmizer LT40 AH Series Bedienungsanleitung
woodmizer
woodmizer LT15 S2-4 E11S Bedienungsanleitung
woodmizer
woodmizer MKI for Pre-97 Sawmills Einrichtungshandbuch
woodmizer
woodmizer LX150 Bedienungsanleitung
woodmizer
woodmizer LT40 Series Bedienungsanleitung
woodmizer
woodmizer LT10 Bedienungsanleitung
woodmizer
woodmizer HR700 Series Bedienungsanleitung
woodmizer
woodmizer LT15 AL-KO Bedienungsanleitung
woodmizer
woodmizer LT40HD Leitfaden
woodmizer
woodmizer EG200 Leitfaden
woodmizer
woodmizer LT20L AH Bedienungsanleitung
woodmizer
woodmizer Simple Set SSW Leitfaden
woodmizer
woodmizer PC200A10 Bedienungsanleitung
woodmizer
woodmizer LX450 Series Bedienungsanleitung
woodmizer
woodmizer LT40L DH Bedienungsanleitung
woodmizer
woodmizer HR150 Bedienungsanleitung
