WORLD TECH ELITE 33054 Bedienungsanleitung

INSTRUCTION MANUAL

ITEM NO. 33054

2.4GHz 4.5CH RC RACING QUADCOPTER

TABLE OF CONTENTS

INTRODUCTION

SAFETY & PRECAUTIONS

DRONE DIAGRAM

TRANSMITTER DIAGRAM

INSTALLING THE TRANSMITTER BATTERY

INSTALLING THE DRONE BATTERY

CHARGING THE DRONE BATTERY

PREFLIGHT PREP / SYNCING THE DRONE TO THE REMOTE

CHANGING THE DRONES SHELL

FLYING THE DRONE - SPECIAL FUNCTIONS

ADJUSTING THE TRIM

POST FLIGHT

REPLACING THE ROTORS

RACING RINGS ASSEMBLY

RACING RINGS ASSEMBLY CONTINUED

FLYING THE DRONE 7

LANDING PADS ASSEMBLY

TROUBLESHOOTING

NOTES: 13

INTRODUCTION

SAFETY & PRECAUTIONS

Thank you for purchasing this amazing World Tech Toys product. This drone is suitable for indoor and

outdoor flight. Please carefully read the entire manual before operating this drone and keep it for

reference in the future.

1. Important Instructions

2. Safety Instructions

3. Flight Environment

4. Attention Before Flying

1) This product is not a toy. It is a precision piece of equipment with integrated mechanical

technologies, electronic, aero dynamics and radio frequencies. To avoid accidents, the

operator must read these instructions carefully prior to operation. If operated incorrectly,

serious physical injury and/or property loss may occur.

2) This product is suitable for operators with previous hobby flying experience, age 14 and up.

3) Only fly in a safe environment that is legal for remote control flying.

4) We are not responsible for the operation and control of this device and related safety

responsibilities.

1) The minimum recommended flying area is 25ft x 25ft x 15ft.

2) Be sure that the transmitter and drone batteries are fully charged.

3) Be sure that the throttle is at its lowest position to avoid premature flight.

4) Always turn on the drone first, then turn on the transmitter. Incorrect operation may result in

failure and the possible influencing of other devices in the area.

5) Ensure that all plugs and wires are secure and in place as they may loosen over time.

The inside of this drone is integrated with precision electronic and mechanical parts. Avoid

contact with water and wet environments as it may result in parts breakdowns and accidents

may occur.

1) Always operate far away from obstacles and crowds. This drone has uncertain flying speeds

and conditions which present potential danger. Fly away from people, animals, high buildings,

high voltage wiring, etc. To ensure a safe and fun flying environment avoid bad weather

conditions like wind, rain, and thunder.

2) Avoid high temperatures. This drone is made of metal, plastic, electronic components and

other materials. Keep away from any heat source and avoid using in high temperatures to

prevent transformation and broken parts resulting from the heat.

DRONE DIAGRAM

TRANSMITTER DIAGRAM

Power Light

Power Button

Flip Stunt ModeSpeed Modes

Turn Left/Right Trim

Ascend/Descend

(Turn Left/Right)

Forward / Backward

(Move Left / Right)

Forward / Backward Trim

Move Left / Right Trim

Headlight

BOTTOM OF DRONE

FRONT

BACK

Battery

Compartment

Rotor

Shell

Power

Switch

Rotor Guards

Landing Skids

Red LED

Lights

Green LED

Lights

Landing

Skids

Battery Cover

4 AA Batteries

(Not included.)

First remove the screw on

the battery cover and then

remove the battery cover

itself. Next, install 4 AA

batteries with the correct

polarity. Finally, replace the

battery cover and screw it

in place.

CAUTION:

1. Make sure the polarity of the

batteries are correctly installed.

2. Do not mix old and new

batteries.

3. Do not mix different types

of batteries.

INSTALLING THE TRANSMITTER BATTERIES

INSTALLING THE DRONE BATTERY

CAUTION WHILE CHARGING:

Do not charge with the batteries still installed. Do not charge the battery unsupervised. Do not immediately

charge after use. Do not overcharge the battery. Ideal charge time is 45-60 minutes. Overcharging can cause

a catastrophic failure. Always charge on dry and ventilated areas away from any heat source or flammable

materials. Always use the original USB charging cable provided. Promptly change and replace old or defective

batteries.

Battery Type Battery Specification Usage Duration Charge Time

BATTERY PACK SPECIFICATIONS

LiPo Battery 3.7V 380mAh Flight Duration 6 - 7 minutes Charging Time 45 -60 minutes

1 3

Connect the batteries power cable

to the drones power port as shown.

Test the drone by flipping the power

switch toward the front of the drone

body. The LED lights should turn on.

Make sure the drone is turned off by

flipping the switch on the side of the

drone towards the drones rear.

CHARGING THE DRONE BATTERY

Completely remove the battery from

the drone by sliding it out toward the

rear of the drone.

Connect the battery pack to the

included USB charger then plug the

USB to any powered USB port. The

USB Charger LED light will turn on

during charging and will turn off

once charging is complete.

Make sure the drone is turned off by

flipping the switch on the side of the

drone toward the rear. Disconnect

the battery power cable from the

drone power port as shown.

Insert the battery from the rear of

the drone into the space under the

drone shell. Make sure the battery

power cable is sticking out of the

back of the drone.

PREFLIGHT PREP / SYNCING THE DRONE TO THE REMOTE

1. Make sure the battery pack is connected properly and the drone shell is secure.

2. Flip the power switch on the side of the drone and place the drone on a flat surface with no

obstructions in its flight path. The drone’s LED lights will begin to flash.

3. Turn on the transmitter by pressing the button at the center. The power indicator on the

transmitter will start flashing.

4. Push the left joystick on the transmitter all the way down, then all the way up and then all the way

back down again. The remote will beep twice and the LED lights on the drone and the power

indicator light on the remote will stop flashing. This means the drone is paired. (If this does not

occur, turn off the remote and drone and try again.

5. Once paired, the drone is ready to fly. All you need to do is gently push up on the transmitter’s

throttle stick and the rotors will start to spin. Continue slowly pushing up on the throttle stick to take

off. It is STRONGLY recommended that you use the drone outdoors during initial flights.

CHANGING THE DRONES SHELL

The drone has a removable shell that you can replace if damaged. You can also change the color of

your drone with a new shell (Sold Separately). Follow the directions to change the drone shell.

Remove the battery first. Focus on one

side of the drone at a time. Push in on

the sides of the drone shell so that the

tabs slide out of the drone tabs.

Once the shell tabs are all released

take the shell off by pulling up and

back towards the rear of the drone.

This will allow you to slide the tab out

the front of the drone.

Insert the new shell’s front tab into the

front of the drone at an angle.

Push the shell back into place and

make sure the side tabs are clipped

back in and secure.

FLYING THE DRONE

BASIC FLYING CONTROLS

Before flying the drone for the first time please read

the instructions carefully and make sure you fully

understand how to control your drone.

Turn Left

Turn Right

Turn Left /Turn Right

Move Right/Move Left

Front

Back

Throttle

Move Forward/Backward

Move RightMove Left

FLYING THE DRONE - SPECIAL FUNCTIONS

LAUNCH TOSS TAKE OFF

Built-in 6-axis gyro technology allows you to throw a successfully readied drone straight into the air to

fly. After the drone is paired to the transmitter, pick it up, toss it into the air and press up on the

throttle. The drone will right itself and level out in midair.

FLIP STUNT MODE

Hover the drone at least 10 feet off the ground. Press the Flip Stunt Mode

button and push the right joystick in the direction you want the drone to

perform a single flip. Normal function will resume after the flip.

SPEED CONTROL

The drone has 3 speed settings: Low, medium and high speed. The drone will always default to the

low speed when you first turn it on. Press the SPEED CONTROL button once and you will hear 2

beeps, meaning it is now on medium speed. Press the SPEED CONTROL button again and you will

hear 3 beeps, meaning it is now on high speed. Press the button again to cycle back to low speed.

ADJUSTING THE TRIM

When the drone moves without transmitter input, adjust the trim controls until hovering is stable.

Drone is turning

to the right.

Move Right

Trim

Push the TURN

LEFT TRIM button

until the drone stops

turning.

Push the BACKWARD

TRIM button until the

drone stops.

Turn Left

Trim

Drone is moving

forward.

Drone is turning

to the left.

Push the TURN

RIGHT TRIM button

until the drone stops

turning.

Turn Right

Trim

FRONT

BACK

Push the FORWARD

TRIM button until the

drone stops.

Forward

Trim

Drone is moving

backward.

FRONT

BACK

Push the MOVE

RIGHT TRIM button

until the drone stops.

Drone is moving

to the left.

Move Left

Trim

Push the MOVE

LEFT TRIM button

until the drone stops.

Drone is moving

to the right.

Backward

Trim

FRONT

BACK

FRONT

BACK

REPLACING THE ROTORS

The rotors may become damaged during a

collision. The drone comes with 4 spare rotors.

Please replace damaged rotors immediately.

The drone comes with 2 A rotors and 2 B rotors.

The A and B rotors must be installed on specific

locations on the drone for it to fly properly. Check

the bottom of each rotor to see if it’s labeled

either A or B. Use the illustration to the right to

install them in the correct location.

FRONT

BACK

A B

B A

The rotor is held by friction so tools are

not needed. Hold the drone and rotor

firmly with each hand and remove the

damaged rotor by pulling upward.

Once removed find the matching new

rotor to replace it with. Match the letter

“A” or “B” on the underside of the

rotors.

Place the correct A or B rotor on top of

the peg. Hold the drone and rotor

firmly with each hand and push the

rotor onto the motors peg.

Repeat the process for any other

rotors that need replacing.

POST FLIGHT

After you are done flying the drone make sure the battery pack is disconnected and the transmitter

power is turned off. If you are not going to use the drone for a long period of time, please remove the AA

batteries from the transmitter to prevent them from draining or leaking.

Inhaltsverzeichnis

Andere WORLD TECH ELITE Quadcopter Handbücher

WORLD TECH ELITE

WORLD TECH ELITE STRIKER-X Bedienungsanleitung

Beliebte Quadcopter Handbücher anderer Marken

dji

dji MAVIC 2 PRO Bedienungsanleitung

Autel Robotics

Autel Robotics EVO II Dual 640T Bedienungsanleitung

Carson

Carson X4 NANO Bedienungsanleitung

Attop

Attop W80 Bedienungsanleitung

Alias

Alias 6608 Bedienungsanleitung

Reely

Reely Drone Copter 2-in-1 Bedienungsanleitung

Hubsan

Hubsan FPV X4 H107D Bedienungsanleitung

Falcon

Falcon S2-210 Bedienungsanleitung

Kaiser Baas

Kaiser Baas KBA15007 Bedienungsanleitung

Denver Electronics

Denver Electronics DCH-261 Bedienungsanleitung

Craig

Craig INTERCEPTOR Bedienungsanleitung

Odyssey

Odyssey TURBO RUNNER Bedienungsanleitung

IMAGINARIUM

IMAGINARIUM droni stream Bedienungsanleitung

Hubsan

Hubsan X4 Pro FPV Bedienungsanleitung

AR.Drone

AR.Drone Parrot VSM Bedienungsanleitung

Walkera

Walkera QR X900 Bedienungsanleitung

dji

dji Phantom 2 Vision + Bedienungsanleitung

HobbyZone

HobbyZone Zugo Bedienungsanleitung