WULI WH-2915F1 Bedienungsanleitung

物理農業機械股份有限公司

WULI AGRICULTURE MACHINE CO., LTD.

動力噴霧機、高壓洗淨機、微霧系統專業設計製造

感謝您購買物理產品，使用前請詳閱本說明。

Thank you for choosing our product.

Please read the manual before use.

W U L I A G R I C U L T U R E M A C H I N E C O . , L T D .

高壓泵浦操作手冊

HIGH PRESSURE PUMP OPERATION MANUAL

MODEL

WH-2915F1

2023.01V

物理 WU LI ─WH-2915F1 (2023.01V) 1

安全須知 Safety Instructions

請放置於乾燥之場所，避免機器銹蝕，影響產品使用壽命。

To reduce the risk of rust and prolong the life of product, please place the pump in a dry

area.

泵浦運轉後溫度會上升，請勿直接碰觸機械表面。

To reduce the risk of burns, do not touch the surface of the pump while operating.

請做好安全防護措施，避免操作運轉時，人員誤觸受傷。

For safety concerns, please keep off the machine while operating.

勿將噴水口直接對準機器、電器、人員或動物。

Do not aim the spray gun at people, animals or any electrical device.

泵浦搭配引擎

.馬達運轉時，在任何檢修保養時，請先關閉，避免危險。

Please completely shut down the unit during maintenance.

本機器必須配合水一同操作使用，缺水將造成機器嚴重損壞。

The unit must not be run without water. Lack of water will cause serious damage to the

pump.

請勿讓兒童使用本機器，使用時請注意兒童安全。

Do not operate the machine near children or animals.

勿在雨天及雷雨中操作。使用時，勿覆蓋物體以避免危險。

Do not operate the unit in the rain or during thunderstorms. When the unit is working, do

not cover it or place it in a closed space with poor ventilation.

泵浦搭配馬達運轉，須注意電壓是否正確，並使用獨立電源，並加裝漏電開關。

Please check whether the voltage is correct and use GFCI plug.

使用前請檢查機油。

Check the pump oil level before each use.

物理 WU LI ─WH-2915F1 (2023.01V) 2

外觀結構 Pump Overview

壓力錶

Pressure Gauge

迴水接頭

Overflow Coupling

出水口

Water Outlet

自動洩壓總成

Unloading Valve Assembly

加油蓋

Oil Inlet Cover

進水口

Water Inlet

排油螺絲

Oil Drainage Screw

油鏡

Oil Window

調壓把手

Pressure Regulating Knob

物理 WU LI ─WH-2915F1 (2023.01V) 3

使用說明

一、操作說明

1. 檢查泵浦與馬達/引擎的每個扣件，是否穩固的鎖緊於架上。

2. 將吸水管接於泵浦進水口鎖緊，並將高壓管接於出水口。

3. 將吸水管(網)放入蓄水槽內並保持水管暢通。吸水過濾網需放置水槽底部上方 20

公分處，預防吸進底部泥沙，確保泵浦壽命，吸水管給水量需大於泵浦使用水量，

如此才能達到使用壓力。

4. 檢查馬達電源是否配接正確電壓；引擎燃料是否正確、充足。

5. 初次啟動泵浦後，請先將泵浦內空氣排出後，停止泵浦。

6. 壓力調整:調整時請依照壓力錶顯示之壓力為參考值，壓力調整弁加壓以順時針方

向調整;反之，以逆時針方向調整。調整壓力時需要打開噴槍;最高壓力不得高於泵

浦設定之壓力，以維護機器壽命。

7. 使用完時，請先關閉動力來源(馬達/引擎)再作動噴槍一次，避免壓力蓄存於高壓

管中。

二、泵浦的潤滑

1. 更換機油時，請將泵浦停止作動，並注意油溫，請冷卻後再進行更換。

2. 初次使用 100 小時應更換機油，以後每使用 300 小時應更換一次。

3. 更換機油時，請旋開洩油螺絲排出骯髒的機油。

4. 將洩油螺絲鎖緊後，打開加油蓋注入#30~#40 之車輛用重型機油，機油應保持在

油鏡 2/3 的位置。

三、特別注意事項

1. 使用自來水作為泵浦的水源。

2. 馬達電源線若要延長時，請依馬力值所需大小法規延長。

3. 確實的更換機油以保持泵浦的潤滑，降低機械損耗。

4. 泵浦與吸水網之高度差(揚程)請勿超過 1.3 公尺。

5. 水溫請勿超過攝氏 60 度。

6. 若使用的水源加入藥劑、肥皂或其他物質，請在使用完畢後以清水沖洗泵浦內部

一分鐘，以延長泵浦的使用壽命。

7. 泵浦的轉速/壓力不得超出建議轉速/壓力的最高值。

8. 請確定馬達/引擎的動力可以配合泵浦。

物理 WU LI ─WH-2915F1 (2023.01V) 4

Operation Instructions

A. Operating Instructions

1. Check every fastener to make sure that the pump and engine/motor are installed

firmly onto the frame.

2. Connect the suction hose to the Water Inlet of the pump and secure the hose;

connect the high pressure hose to the Water Outlet.

3. Put the suction hose (with filter) into the water tank and make sure that water

flows smoothly. Please suspend the suction filter around 20cm above the bottom

of the water tank to avoid suctioning residue which might reduce the product’s

life.

4. Check if the motor is connected to the right voltage; check if the engine fuel is

suitable and sufficient.

5. Always release air from the pump when first starting it.

6. Pressure adjustment:

◇Check the pressure displayed on Pressure Gauge for reference when adjusting it.

◇The maximum pressure should not exceed the pump’s working pressure.

◇Hold the spray gun trigger when adjusting the pressure.

◇Turn the knob clockwise to increase pressure; counterclockwise decrease.

7. When finished using the pump, turn off the power of motor or engine and

squeeze the spray gun trigger again to release the pressure stored in the high

pressure hose.

B. Oil Change

1. Replace the oil in the pump after the first 100 hours of use. After this, the oil

should be changed after every 300 hours of use.

2. Unscrew the Oil Drainage Screw and drain the oil from the pump.

3. Tighten the Oil Drainage Screw before refilling with clean motor oil SAE

#30~#40 up to the level of 2/3 of the Oil Window.

※Attention: When replacing the oil, please turn off the product and

make sure that the oil temperature has cooled before replacing.

物理 WU LI ─WH-2915F1 (2023.01V) 5

C. Reminders

1. Always use clean water with the product.

2. If using an extension cord, please follow the electrical regulations and select the

appropriate power cord diameter.

3. Be sure to change the oil according to the Oil Change section or the pump might

be damaged.

4. The pump’s location should be no more than 1.3 meters higher than the suction

filter.

5. The water temperature should not exceed 60℃.

6. If using water containing chemicals, detergents or other substances, please run

the pump with clean water for one minute after use to prolong its service life.

7. The pump’s revolution and working pressure should not exceed the maximum

suggested values.

8. Please make sure the motor or engine power is suitable for the pump.

Operation Instructions

物理 WU LI ─WH-2915F1 (2023.01V) 6

故障診斷與排除

以下提供簡易的故障排除方式，若有任何問題，請您向當地之經銷商洽詢，

同時記得提供您所購買的機器型號與製造編號。

故障的現象

原因

解決方式

無法吸水/出水

◎泵浦內部損壞或阻塞

◎噴槍或噴嘴阻塞

◎活門總成異物阻塞或磨損

◎泵浦與水槽距離與高度超

出範圍

◎泵浦吸入空氣

◎清潔或維修泵浦，及清潔吸水過濾

網

◎清潔或維修噴槍/噴嘴

◎清潔活門總成或更換零件(第17 頁圖一)

◎改善水槽或泵浦位置，清洗機與吸

水網之高度差(揚程)請勿超過 1.3 公

尺

◎拔掉噴槍，待出水正常後再接上

運轉聲音異常

◎引擎有問題

◎泵浦吸入空氣

◎活門總成異物阻塞

◎吸水量不足

◎清潔或維修引擎

◎打開出水管排氣

◎清潔活門總成(第17 頁圖一)

◎檢查吸水管是否有細縫，或者扭曲

進氣及清潔吸水管過濾網

調壓問題或

壓力無法上升

◎壓力閥或閥座磨損

◎迫緊磨損

◎活門塞與活門座沾黏

◎閥座上有異物

◎活門總成磨損

◎活門總成異物阻塞

◎噴嘴磨損導致壓力下降

◎泵浦吸入空氣

◎自動洩壓總成損壞

◎更換零件

◎更換零件(第17 頁圖二)

◎拆解後清洗活門總成或更換零件(第

17 頁圖一)

◎清潔閥座

◎更換零件(第17 頁圖一)

◎清潔活門總成(第17 頁圖一)

◎更換噴嘴

◎檢查吸水管接頭鎖合或吸水管破裂

◎送回經銷商更換

物理 WU LI ─WH-2915F1 (2023.01V) 7

Troubleshooting

The following are simple troubleshooting methods. If you have any

questions, please contact your local dealer and remember to provide the

model and serial number of the product you purchased.

Problem

Cause

Solution

The pump

fails to

deliver

water

◎The pump is blocked or

damaged.

◎The spray gun or nozzle is

blocked.

◎The valve assemblies are

stuck or worn out.

◎The distance or height

between the pump and the

water tank exceeds the

limit.

◎Air in the pump.

◎Clean or maintain the pump and

suction filter.

◎Check and clean the spray gun

and nozzle.

◎Clean or replace the valve

assemblies. (P.17 Dia.1)

◎Make sure the pump’s location is

no more than 1.3m higher than

the suction filter.

◎Disconnect the spray gun until

the water flow is stable.

Unusual

noise

◎Engine problems

◎There is air in the pump.

◎The valve assemblies are

blocked.

◎The water supply is not

enough.

◎Clean or maintain the engine.

◎Disconnect the spray gun until

the water flow is stable.

◎Clean the valve assemblies. (P.17

Dia.1)

◎Check the suction hose and

fittings; make sure they are well

connected and in good condition.

◎Clean the suction filter.

** Continues on page 8 **

物理 WU LI ─WH-2915F1 (2023.01V) 8

Problem

Cause

Solution

Pressure

adjustment

problem

◎The pressure valve or the

pressure valve seat is

worn out, damaged or

blocked.

◎The packings are worn

out.

◎The valve assemblies are

worn out or blocked.

◎The pressure decreases

due to nozzle wear.

◎Air in the pump.

◎The Unloading Valve

Assembly is damaged.

◎Clean the pressure valve or

replace the worn out or damaged

spare parts.

◎Replace the packings. (P.17

Dia.2)

◎Clean or replace the valve

assemblies. (P.17 Dia.1)

◎Replace the nozzle.

◎Check the Suction Hose and

fittings; make sure they are well

connected and in good condition.

◎Return the product to your local

dealer to repair or replace the

Unloading Valve Assembly.

Troubleshooting

WH-2915F1

Inhaltsverzeichnis

Andere WULI Wasserpumpe Handbücher

WULI

WULI WH-1030B Bedienungsanleitung

WULI

WULI WH-2915F Bedienungsanleitung

WULI

WULI WS-2024F1 Bedienungsanleitung

WULI

WULI WL-550B2 Series Bedienungsanleitung

WULI

WULI WS-3000DT Bedienungsanleitung

WULI

WULI WH-2024F Bedienungsanleitung

WULI

WULI WH-1030B2 Bedienungsanleitung

WULI

WULI WH-2075 Bedienungsanleitung

WULI

WULI WH-3520F Bedienungsanleitung

WULI

WULI WH-1035F Bedienungsanleitung

WULI

WULI WH-5012F Bedienungsanleitung

Beliebte Wasserpumpe Handbücher anderer Marken

Neptun

Neptun NPHW 5500 Bedienungsanleitung

Sensidyne

Sensidyne Gilian BDX-II Montage- und Bedienungsanleitung

Draper

Draper 47808 Bedienungsanleitung

Trolla

Trolla 12820 Bedienungsanleitung

Sunfab

Sunfab SVH Series Bedienungsanleitung

WilTec

WilTec 50740 Bedienungsanleitung

Fieldmann

Fieldmann FVC 5015 EK Bedienungsanleitung

Everbilt

Everbilt EFSUB5-122HD Bedienungsanleitung

Graco

Graco Husky 3300e Bedienungsanleitung

esotec

esotec 101018 Bedienungsanleitung

moyno

moyno 2000 CC Bedienungsanleitung

Becker

Becker BASIC VASF 2.80/1-0.AC230 Bedienungsanleitung

Sykes AmeriPumps

Sykes AmeriPumps GP100M Fehlerbehebungshandbuch

DUROMAX

DUROMAX XP WX Series Bedienungsanleitung

BRINKMANN PUMPS

BRINKMANN PUMPS SBF550 Bedienungsanleitung

Franklin Electric

Franklin Electric IPS Bedienungsanleitung

Xylem

Xylem e-1532 Series Bedienungsanleitung

Milton Roy

Milton Roy PRIMEROYAL Bedienungsanleitung