Xantrex IP1012 AL Bedienungsanleitung

IP1012 AL

Inverter/Charger

with Ignition

Protection

Owner’s Guide

IP1012 AL

IP1012_AL.book Page i Tuesday, May 1, 2007 12:18 PM

IP1012_AL.book Page ii Tuesday, May 1, 2007 12:18 PM

IP1012 AL Inverter/

Charger with Ignition

Protection

Owner’s Guide

IP1012_AL.book Page i Tuesday, May 1, 2007 12:18 PM

About Xantrex

Xantrex Technology Inc. is a world-leading supplier of advanced power electronics and controls with

products from 50 watt mobile units to 1 MW utility-scale systems for wind, solar, batteries, fuel cells,

microturbines, and backup power applications in both grid-connected and stand-alone systems. Xantrex

products include inverters, battery chargers, programmable power supplies, and variable speed drives

that convert, supply, control, clean, and distribute electrical power.

Trademarks

IP1012 AL Inverter/Charger with Ignition Protection is a trademark of Xantrex International. Xantrex is

a registered trademark of Xantrex International.

Other trademarks, registered trademarks, and product names are the property of their respective owners

and are used herein for identification purposes only.

Notice of Copyright

©IP1012 AL Inverter/Charger with Ignition Protection Owner’s Guide April 2007 Xantrex

Exclusion for Documentation

UNLESS SPECIFICALLY AGREED TO IN WRITING, XANTREX TECHNOLOGY INC. (“XANTREX”)

(A)MAKES NO WARRANTY AS TO THE ACCURACY, SUFFICIENCY OR SUITABILITY OF ANY TECHNICAL OR

OTHER INFORMATION PROVIDED IN ITS MANUALS OR OTHER DOCUMENTATION.

(B)ASSUMES NO RESPONSIBILITY OR LIABILITY FOR LOSSES, DAMAGES, COSTS OR EXPENSES, WHETHER

SPECIAL, DIRECT, INDIRECT, CONSEQUENTIAL OR INCIDENTAL, WHICH MIGHT ARISE OUT OF THE USE OF

SUCH INFORMATION. THE USE OF ANY SUCH INFORMATION WILL BE ENTIRELY AT THE USER’SRISK; AND

(C)REMINDS YOU THAT IF THIS MANUAL IS IN ANY LANGUAGE OTHER THAN ENGLISH, ALTHOUGH

STEPS HAVE BEEN TAKEN TO MAINTAIN THE ACCURACY OF THE TRANSLATION, THE ACCURACY CANNOT

BE GUARANTEED. APPROVED XANTREX CONTENT IS CONTAINED WITH THE ENGLISH LANGUAGE

VERSION WHICH IS POSTED AT WWW.XANTREX.COM.

Date and Revision

April 2007 Revision A

Part Number

975-0337-01-01

Product Number

805-1011

Contact Information

Telephone: 1 800 670 0707 (toll free North America)

1 360 925 5097 (direct)

Fax: 1 800 994 7828 (toll free North America)

1 360 925 5143 (direct)

Email: [email protected]

Web: www.xantrex.com

IP1012_AL.book Page ii Tuesday, May 1, 2007 12:18 PM

iii

About This Guide

Purpose

The purpose of this Owner’s Guide is to provide explanations and

procedures for installing, operating, maintaining, and troubleshooting the

IP1012 AL Inverter/Charger with Ignition Protection.

Scope

The Guide provides safety guidelines, detailed planning and setup

information, procedures for installing the inverter, as well as information

about operating and troubleshooting the unit. It does not provide details

about particular brands of batteries. You need to consult individual

battery manufacturers for this information.

Audience

The Guide is intended for anyone who needs to install and operate the

IP1012 AL Inverter/Charger with Ignition Protection. Installers should be

certified technicians or electricians.

Organization

This Guide is organized into four chapters and an appendix.

Chapter 1, “Introduction” describes the main performance and protection

features of the IP1012 AL Inverter/Charger with Ignition Protection.

Chapter 2, “Operation” explains how to calculate the size of the loads you

can run from the IP1012 AL. It also provides guidelines to help you run

loads safely and efficiently.

Chapter 3, “Maintenance” provides procedures for checking the terminal

connections on the inverter/charger, disconnecting the IP1012 AL from

the batteries, changing the overcurrent protection fuse and removing or

connecting the AC input and output cables.

IP1012_AL.book Page iii Tuesday, May 1, 2007 12:18 PM

Safety

iv 975-0337-01-01

Chapter 4, “Troubleshooting” provides information to help you identify

common problems which may occur. Read this chapter before calling

your authorized Xantrex dealer. If you cannot solve the problem, record

the details as suggested on “Information About Your System” on

page WA–4, then call your dealer.

Appendix A contains the inverter, charger, and transfer specifications for

the IP1012 AL. The specifications show rating curves for output surge,

current versus temperature, and pass-through current. Appendix A also

illustrates the three-stage charging profile used by the unit.

Conventions Used

The following conventions are used in this guide.

Related Information

You can find more information about Xantrex Technology Inc. as well as

its products and services at www.xantrex.com

WARNING

Warnings identify conditions or practices that could result in personal injury or

loss of life

CAUTION

Cautions identify conditions or practices that could result in damage to the unit or

other equipment.

Important:

These notes describe things which are important for you to know,

but not as serious as a caution or warning.

IP1012_AL.book Page iv Tuesday, May 1, 2007 12:18 PM

Important Safety Information

General Precautions

1. Before using the inverter/charger, read all appropriate sections of this

guide and any cautionary markings on the inverter and the batteries.

2. Use the grounded AC cord supplied when connecting to AC input

power (qualified external AC which is when the external AC power is

100–130 Vac/54–66 Hz). Do not remove or attempt to defeat the

ground connection to the qualified external AC source in any way. If

an extension cord is necessary, ensure that it is at least 12 AWG and

no longer than 12 feet in length.

3. If possible, plug the inverter/charger into an AC source outlet that is

protected by a Ground Fault Circuit Interrupting (GFCI) device;

either a breaker or outlet.

4. Do not operate the inverter/charger if it has received a sharp blow,

been dropped, or otherwise damaged. If the unit is damaged, return it

to your authorized Xantrex dealer.

5. Do not dismantle the inverter/charger; it contains no user- serviceable

parts. Attempting to service the unit yourself could cause electrical

shock or fire. Internal capacitors remain charged after all power

is disconnected.

6. To reduce the risk of electrical shock, turn off the inverter/charger

from the remote switch, then disconnect both AC (shorepower) and

DC (battery) power from the unit before working on any circuits

connected to it. Turning off the remote On/Off switch alone does not

reduce this risk.

Important::

Save these instructions. This guide contains important

safety and operating instructions for the IP1012 AL Inverter/Charger with

Ignition Protection.

IP1012_AL.book Page v Tuesday, May 1, 2007 12:18 PM

Safety

vi 975-0337-01-01

Precautions When Working With Batteries

1. Follow all instructions published by the battery manufacturer and the

manufacturer of the equipment in which the battery is installed.

2. Make sure the area around the battery is well ventilated.

3. Never smoke or allow a spark or flame near the vehicle engine or a

battery.

4. Use caution to reduce the risk of dropping a metal tool on a battery. It

could spark or short circuit the battery or other electrical parts and

cause an explosion.

5. Remove metal items like rings, bracelets, and watches when working

with lead-acid batteries. These batteries produce a short-circuit

current high enough to weld a ring, other metal jewellery or tools,

thus causing severe burns.

6. If you need to disconnect a battery, always remove the negative

terminal from the battery first. Make sure all accessories are off so

you don’t cause an arc.

7. Before making the final connection to a battery, be sure the polarity is

correct; negative-to-negative, and positive-to-positive.

8. When you are making the final connection to a battery, you will see a

spark and hear a loud pop. This spark and popping sound is normal.

Precautions for Using Rechargeable Devices

Most battery-operated equipment uses a separate charger or transformer

that is plugged into an AC receptacle and produces a low voltage output.

If the label on the AC adapter or charger states that the adapter or charger

produces a low voltage AC or DC output (less than 30 volts), the inverter/

charger can power this charger or adapter safely.

Some chargers for small nickel-cadmium batteries can be damaged if

connected to the inverter/charger. Do not use the following loads and

appliances:

• Small battery-operated appliances like flashlights, razors, and night

lights that can be plugged directly into an AC receptacle to recharge.

• Some chargers for battery packs used in hand power tools. These

types of chargers display a warning label stating that dangerous

voltages are present at the battery terminals.

IP1012_AL.book Page vi Tuesday, May 1, 2007 12:18 PM

975-0337-01-01 vii

Important Safety Information

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -v

Introduction

Inverter/charger Features - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 1–2

Operating Features - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 1–3

Operation

Planning for AC Loads - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2–2

Type of Loads - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2–2

AC loads - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2–2

DC loads - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2–3

Problem loads - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2–3

Ambient Temperature - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2–3

Calculating Size of an AC Load - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2–4

Running the Alternator While Operating AC and DC Loads - - - - - - - - - - - - - - 2–7

Using the Remote Switch- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2–9

Operating the Inverter/Charger - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2–11

Turning the Inverter On and Running Loads - - - - - - - - - - - - - - - - - - - - - - - - 2–11

Running in Extremes Of Hot or Cold Temperatures - - - - - - - - - - - - - - - - - - - 2–11

Restarting After a Shutdown - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2–11

Battery Charging - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2–12

Using Shorepower - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2–12

Miscellaneous Hints - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2–12

Maintenance

Maintaining the Inverter/charger - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3–2

Checking Terminals - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3–2

Disconnecting and Connecting the Batteries - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3–3

Disconnecting - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3–3

Connecting - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3–3

Replacing the Fuse - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3–4

Removing and Reconnecting AC Cables - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3–6

Contents

IP1012_AL.book Page vii Tuesday, May 1, 2007 12:18 PM

Contents

viii 975-0337-01-01

Troubleshooting

Troubleshooting- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 4–2

Common Problems - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 4–2

Blinking Lights on the Remote Switch - - - - - - - - - - - - - - - - - - - - - - - - - - - - 4–3

Specifications

Physical Specifications - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -A–2

Inverter Specifications - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -A–3

Charger Specifications - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -A–4

Transfer and General Specifications - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -A–5

Rating Curves and Charging Profiles- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -A–6

IP1012_AL.book Page viii Tuesday, May 1, 2007 12:18 PM

Inhaltsverzeichnis

Andere Xantrex Wechselrichter Handbücher

Xantrex

Xantrex XPower 175 PLUS Bedienungsanleitung

Xantrex

Xantrex 120 VAC/60 Bedienungsanleitung

Xantrex

Xantrex PROwatt 3000 Bedienungsanleitung

Xantrex

Xantrex Xantrex PRO XM 1000 Bedienungsanleitung

Xantrex

Xantrex FREEDOM SW 3000 Bedienungsanleitung

Xantrex

Xantrex PROwatt SW 2000i Bedienungsanleitung

Xantrex

Xantrex Freedom X 1200 120VAC Bedienungsanleitung

Xantrex

Xantrex XS400 Bedienungsanleitung

Xantrex

Xantrex GT2.8-AU-QC-230 Bedienungsanleitung

Xantrex

Xantrex Freedom Xi 1000 Bedienungsanleitung

Xantrex

Xantrex XPower 450 Bedienungsanleitung

Xantrex

Xantrex PV-30208 Bedienungsanleitung

Xantrex

Xantrex XPower Pocket Inverter 175 Bedienungsanleitung

Xantrex

Xantrex ENERGY HW 1000 Bedienungsanleitung

Xantrex

Xantrex XPower 150 Bedienungsanleitung

Xantrex

Xantrex XPower 1500 Bedienungsanleitung

Xantrex

Xantrex Prosine PS2.5 and Betriebsanleitung

Xantrex

Xantrex XW4024-120 Bedienungsanleitung

Xantrex

Xantrex PowerHub PH1800 Handbuch

Xantrex

Xantrex 6000 Series Bedienungsanleitung

Xantrex

Xantrex GT5.0-NA-240 Bedienungsanleitung

Xantrex

Xantrex HI400 Bedienungsanleitung

Xantrex

Xantrex SW Plus 2524 Bedienungsanleitung

Xantrex

Xantrex Freedom 458 Series Bedienungsanleitung

Beliebte Wechselrichter Handbücher anderer Marken

Fourgroup

Fourgroup Easy Bedienungsanleitung

Velleman

Velleman PI300M Bedienungsanleitung

Sungrow

Sungrow SG350HX-US Bedienungsanleitung

WilTec

WilTec 61897 Bedienungsanleitung

SMA

SMA SUNNY BOY STORAGE 2.5 Bedienungsanleitung

Simplicity

Simplicity LANDLORD 316 Bedienungsanleitung

Santak

Santak SMAX 3000 Bedienungsanleitung

ATON

ATON RA.Store-3 Bedienungsanleitung

ZIEHL-ABEGG

ZIEHL-ABEGG FXET4AMQ Bedienungsanleitung

Tektronix

Tektronix CFG250 Bedienungsanleitung

Champion

Champion 200989 Bedienungsanleitung

Vanner

Vanner 20-500 Series Bedienungsanleitung

GE GEP Bedienungsanleitung

MULTIQUIP

MULTIQUIP GDP-5H Leitfaden

Astrel Group

Astrel Group Power Reducer Kurzanleitung

GoWISE

GoWISE PS1007 Bedienungsanleitung

Promate

Promate PM13500D ES Bedienungsanleitung

Mastervolt

Mastervolt WHISPER 3.5M3000 RPM Bedienungsanleitung