XEPA PSO1 Bedienungsanleitung
Please do not return this item to the store.
For service or questions about your solar light, call our customer service at
800.284.8828 (8:30am - 5:30pm, Monday to Friday, Pacific Time) or visit
www.xepatech.com.
Motion Activated
Solar Powered LED
Security Light
MODEL: PSO1
Introduction
Thank you for purchasing the PSO1 Solar Powered SecurityLight—the
most cost-effective way to illuminate and protect your home, business,
and recreational areas. With its easy setup and lightweightdesign, this
light conforms to most of your lighting needs and is especially useful
wherever an electrical outlet is not accessible.
The PSO1 Solar-Powered Security Light converts solar energy to
electricity so that lighting is available wherever and whenever you
desire. Simply install or set the solar charging panel where sun exposure
is prevalent. The attached 15’cable provides sufficient length for easy
placement. In AUTO mode, (normal operation setting) the light
illuminates at night only when motion is detected, then automatically
resets.
1
Important Safety Information
•Do not expose the light to fire or intense heat.
•Do not immerse in water.
•Never look directly into the light or shine it in another person’s eyes.
•Dispose of the battery in accordance with local, state and
federal regulations. (Do not burn or discard the battery in a
municipal water system or other body of water.)
•Consult your local safety guidelines for installing the light
fixture on a building.
•Only use batteries from XEPATECHNOLOGIES to ensure
compatibility. (Refer to the product’s original battery for correct
size.)
•Always position the battery so it has the correct polarity: (+) and (-).
•Light will not work once battery is removed from the jacket.
Please plug in the solar panel charger or any other approved power
adaptor after put battery back to the jacket to reactivate the light.
2
What’s Inside the Package:
• PSO1 solar light with battery
• Solar charging panel with 15’ cable
• User manual including installation template for the light and
solar panel
• Screws & anchors
Features:
• Solar powered lighting, no electricity bill
• 2 x 5W super bright LEDs (equivalent to 60W incandescent)
• Motion detection at a distance of up to 50 ft.
• Two lamp heads for dual direction illumination
• Auto illumination from dusk to dawn High-efficiency, rechargeable
lithium battery produces zero emissions
3
Product Profile:
1. Lamp Head
2. Battery Housing
3. Horizontal Adjust Knob
4. Vertical Adjust Knob
5. Motion Activated Indicator
6. Motion Sensor Lens
7. Adjust Knob
4
Installation Recommendations:
• The PSO1 light fixture should be installed on a flat and stable
surface— the higher the light is placed, the larger the area of
illumination.
• Avoid installing the light near an air conditioner, heater or high-
voltage system, since quick changes in temperature may activate the
motion- detection system and run down the light’s power.
• Avoid positioning the motion sensor head towards street traffic, or
where other movements may trigger the light needlessly and drain
the battery.
• The solar panel should be installed facing the sky where direct
sunlight can shine on the panel at least 6-8 hours per day. (Before
initial use, the panel will need 2-3 days of sunlight exposure to fully
charge the battery.)
• The motion sensor is most sensitive to movement across the device
and less sensitive to motion directly towards or away from it.
• Periodically use a soft damp cloth to clean accumulated dust or
snow off of the solar panel. This will preserve the panel’s efficiency
when charging the battery.
5
Installing the LED Security Light:
1. Mark holes on the wall through the Installation template.
2. Drill holes with a 3/16” drill bit.
3. Gently tap the plastic anchors into the holes until they are flush with
the mounting surface.
4. Secure the screws into the plastic anchors—leave approximately
3/16” of each screw exposed for mounting the unit.
5. Place the light unit over the screws—gently push down on the unit to
slide the screws into locking position.
6
6. Rotate/tilt the motion-detection sensor towards the desired coverage
area.
Installing the Solar Panel:
1. Find a location for the solar panel that receives direct sunlight for a
minimum of 6-8 hours a day and is within 15’of where the Security
Light will be installed.
2. Mark the holes through the installation template.
3. Using a 3/16” drill bit, drill holes in the spots you marked. 7
4. Gently tap the mounting anchors into the holes until they are flush
with the mounting surface.
5. Place the base of the solar panel over the drilled holes—secure the
screws through the base into the plastic mounting anchors.
6. Extend the cord from the solar panel to the light box—completely
insert the cable plug into the INPUT hole located on the bottom of the
light unit.
7. Adjust the motion-detection sensor towards the desired coverage area.
8
Light Functions:
• OFF: The light will not function; product will be completely off.
• AUTO: The light will remain dormant during daylight hours. At
night, the light will activate only when the motion sensor detects an
infrared signal, turning off after 60 seconds.
• TEST: LED light will illuminate continuously for 5 minutes and
flicker for 1 minute to ensure the appropriate settings are in place.
(Be sure to switch the light to AUTO when testing is complete.)
Recharging the Battery:
• Plug in the solar panel charger; the battery will charge whether the
switch is set to OFF, AUTO, or TEST positions.
• You can also charge the light with an approved power adapter
(9V/2000mA adapter not included in packaging, but available on
www.xepatech.com).
• Light will not work once battery is removed from the jacket. Please
plug in the solar panel charger or any other approved power adaptor
after put battery back to the jacket to reactivate the light. 9
Inhaltsverzeichnis
Sprachen:
Beliebte Scheinwerfer Handbücher anderer Marken
VIZULO
VIZULO Micro Martin Benutzerhandbuch
EuroLite
EuroLite LED IP FL-100 SMD Bedienungsanleitung
Cooper Wheelock
Cooper Wheelock XB12 Bedienungsanleitung
Allen + Roth
Allen + Roth 17624-000 Bedienungsanleitung
ADJ
ADJ 4 STAGE PAK Bedienungsanleitung
Cooper Lighting
Cooper Lighting EGL91SW233 Bedienungsanleitung
