XIEGU X5105 Bedienungsanleitung

XIEGU COMMUNICATION

X5105

HF+50MHz Portable HF Transceiver

Instruction Manual

Chongqing Xiegu Technology Co.,Ltd.

www.cqxiegu.com

Important reminder:

Before operating the equipment, please

read our operating manual carefully and

keep the manual, so as not to lose.

Security considerations:

Do not use equipment during a lightning storm.

Damp-proof!

Don't illegal operations!

Note RF high-voltage of antenna connector!

Features:

l3.6 inch LCD screen

lBuilt in 3800mAh large capacity battery

pack

lBuilt in ATU

lCovers all modes of HF, 50MHz band

(SSB/CW/AM/FM/RTTY/PSK)

lIF signal output

lBuilt in AF-DSP digital noise reduction

processor

lEquipped with trestle for desktop

operation

lVery small in size and ultra portable

Packing list:

Qty

①X5105...... ...... ...... ...... ...... ...... ...... 1

②Power supply cable........... ........... ......1

③Hand microphone.............. ........... .....1

④USB Cable........... ........... ........... .........1

⑤Service card................. ........... ........... 1

①

②

④

③⑤

1 X5105 Specifications

Basic Specifications

Frequency range:

Receive: 1MHz-55MHz-

Transmitting: 160 meters -6 meters (Amateur band only)

Operating mode: A1A(CW)，A3E(AM)，J3E(USB/LSB)，F3E(FM)

minimum frequency stepping: 1Hz

Antenna impedance: 50Ω

Operating temperature range: -10℃~ +60℃

Frequency stability: after turn on the radio 1-60 minutes is ±2ppm,

@25℃：1ppm/hour

supply voltage: normal: 13.8VDC + 15%, negative grounding

Operating voltage: 9.0-15.0VDC, negative grounding

Current consumption: receive: 660mA@ Max transmit: 2.5A@ Max

Battery capacity: 3800mAh @12V

Dimensions: 160*100*46mm[does not include protrusion]

Weight: 0.94Kg[host only]

Transmitter parameters

Transmitter power：5W(SSB/CW/FM)，1.5W(AM carrier)，@13.8VDC

Modulation mode: SSB balanced modulation/AM low level amplitude modulation/FM

Variable reactance frequency modulation

FM Maximum frequency swing: ±5kHz

spur reduction: -45dB

Carrier suppression: ＞40dB

Sideband spurious: ＞50dB

SSB frequency response: 400Hz-2800Hz（-6dB）

Microphone impedance: 200-10k(conventional 600Ω)

Receiving parameters

Circuit type: double frequency conversion superheterodyne + audio DSP

IF frequency: first IF: 70.455MHz second IF: 10.695MHz third IF: 455kHz（FM）

Sensitivity

(PRE=on，ATT=off，NB=off，NR=off，SSB/CW/AM = 10dB S/N，FM = 12dB SINAD)

Image rejection: 70dB

If Rejection: 60dB

Selectivity: SSB：-6dB:2.4kHz/-60dB:4.6kHz

CW：-6dB:500Hz/-60dB:2000Hz

AM：-6dB:6.0kHz/-60dB:25.0kHz

FM：-6dB:12.0kHz/-60dB:25.0kHz

Audio output: 0.6W （8Ω，≤10% THD）

Audio output impedance: 4 – 16Ω

SSB/CW AM FM

500kHz-1.8MHz / 10uV /

1.8MHz-28MHz 0.25uV 2uV /

28MHz-30MHz 0.25uV 2uV 0.35uV

50MHz-54MHz 0.25uV 2uV 0.35uV

Interface definition

Charging and maintenance of internal battery

X5105 has a built-in 5000mAh battery pack. When the external power supply is not

connected, the battery pack supplies power to the X5105, when the X5105 is connected

with an external power supply, the circuit inside the machine automatically switches to

the external power supply.

Charging method:

1In the menu, select [CHG] option, start charging function.

2The external power supply voltage is set between 13.5V-14.0V and the power supply

is connected to the X5105 external power supply.

The host will automatically start charging.

3Charging time is 10 hours. By then, the charge will automatically stop.

When the battery is powered for X5105, when the battery power is about to run out, the

power indication sign on the upper right corner of the screen is displayed as . At this

point, the X5105 should be charged or switched to an external power supply. During the

charging process, the casing of the machine has a slight fever.

Normally, the lifetime of the internal battery is about 4-5 years. Please replace the battery

when the battery has a noticeable capacity drop or charge fails.

When the X5105 is connected to an external power source, and when the X5105 is in the

transmitting state, it is strictly forbidden to disconnect the power supply so as not to

damage the power management chip.

Please turn off the power immediately when the machine shell is very hot near the

battery, and put the equipment in a safe and ventilated place. After confirming the

safety situation, please contact us for proper handling.

2 Description of equipment

2.1 Front panel button function

①Power button

Press this button for a second to turn on or turn off the radio.

②Mode button

With this key, you can change the mode of operation and will cycle in the following mode:

[LSB-USB-CW-AM-FM]

③PRE/ATT button

With this key, the preamplifier or pre attenuator will be turned on or be turn off in the

following states: [PRE=ON--ATT=ON--PRE/ATT=OFF]

④RIT button

With this key, the receive frequency adjustment function is turned on or turn off.

⑤NB button

With this key to turn on or turn off the NB function.

⑥MENU button

With this key, you can switch the current display of the multi-function menu.

⑦-⑩Multifunctional menu button

Press these four buttons to turn on or off the corresponding function displayed on the

menu area on the current screen.

○

11 Major tuning knob

The main tuning knob of X5105, can be used either for frequency regulation or for menus.

○

12 ATU button

When the key is pressed for a short time, the automatic antenna tuner will be connected

to the antenna port, by pressing this button for a long time, the automatic antenna tuner

will be started.

○

13 Po button

With this key, and with the main tuning knob, the power of the transmitter can be

adjusted. The range of adjustment is from 0.5W-5W, stepping for 0.5W.

○

14 A/B button

With this key, you will switch between VFOA-VFOB.

○

15 ＜button

With this key, the current frequency step carries one bit to the left.

○

16 ＞button

With this key, the current frequency step carries one bit to the right.

○

17 V/M button

With this key, you can switch between VFO mode and MEMO mode.

○

18 Up button

With this key, X5105 can be switched to higher frequency bands.

○

19 DN button

With this key, X5105 can be switched to lower frequency bands.

○

20 －button

With this key, you can reduce current volume.

○

21 ＋button

With this key, you can increase current volume.

○

22 PTT button

Press and hold this button, X5105 will go into the transmit state.

○

23 LOCK button

If you press this button for a short time, you will lock all buttons and knobs on the panel;

By pressing this button for a long time, you can set the backlight on / off.

Status indicator

A [T/R] B [DATA] C [LINK]

Transmit/Receive

switch indication

Data

indication

Peripheral

connection

indication

Indicator color description:

A T/R indicator

When the X5105 is in receiving mode, the indicator light is green.

When the X5105 is in transmitting mode, the indicator light is red.

B DATA indicator

When the data signal or channel are busy, the indicator light flashes.

C LINK indicator

When the host is connected with the external equipment, the indicator light will shine.

Function menu corresponding to 4 multi-function buttons below screen.

A=B SPL NR NTH

Copy VFOA to VFOB Split On/Off Digital noise

reduction

Notch

AGC FIL

Automatic gain

control on / off,

control speed

Filter selection

M>V MW MC TAG

Save the current

channel in VFO and

return to VFO mode

Store current

channel

Clear current

channel

Channel display

frequency / custom

characters(Press this

button for a long

time to enter the

TAG edit mode)

KEY KSP

Key manual /

automatic mode

selection

Automatic key rate

selection

RE1 RE2 RE3 /

Set CW message

1(Press this button

for a long time to

enter the CW

message content

editor)

Set CW message

2(Press this button

for a long time to

enter the CW

message content

editor)

Set CW message

3(Press this button

for a long time to

enter the CW

message content

editor)

SQL CMP MTR MSL

Squelch function Speech compression switch display

Po/SWR

Internal / external

microphone

selection

SRM

Scan receive

mode(frequency

spectrum)

IFO VER

IF output switch Version information

display

Screen display information

Andere Handbücher für X5105

Inhaltsverzeichnis

Andere XIEGU Transceiver Handbücher

XIEGU

XIEGU X108G Bedienungsanleitung

XIEGU

XIEGU G106 Bedienungsanleitung

XIEGU

XIEGU G90S Bedienungsanleitung

XIEGU

XIEGU X108G Bedienungsanleitung

XIEGU

XIEGU G90 Bedienungsanleitung

XIEGU

XIEGU X6100 Bedienungsanleitung

XIEGU

XIEGU G1M Bedienungsanleitung

XIEGU

XIEGU G90 Bedienungsanleitung

XIEGU

XIEGU G106 Bedienungsanleitung

XIEGU

XIEGU G90 Bedienungsanleitung

XIEGU

XIEGU G90 Bedienungsanleitung

XIEGU

XIEGU G1M Bedienungsanleitung

XIEGU

XIEGU G90 Bedienungsanleitung

XIEGU

XIEGU X108 Bedienungsanleitung

XIEGU

XIEGU X6100 Bedienungsanleitung

XIEGU

XIEGU X5105 Bedienungsanleitung

XIEGU

XIEGU X5105 Bedienungsanleitung

XIEGU

XIEGU G90 Bedienungsanleitung

XIEGU

XIEGU X1M Pro Bedienungsanleitung

XIEGU

XIEGU X6100 Bedienungsanleitung

XIEGU

XIEGU G90 Bedienungsanleitung

XIEGU

XIEGU X5105 Gebrauchsanweisung

XIEGU

XIEGU X108G Bedienungsanleitung

XIEGU

XIEGU X108G Bedienungsanleitung

Beliebte Transceiver Handbücher anderer Marken

Yaesu

Yaesu FT-7B Bedienungsanleitung

Kenwood

Kenwood ProTalk TK-3201 Bedienungsanleitung

Texas Instruments

Texas Instruments TLK10232 Bedienungsanleitung

Mizuho

Mizuho MX-2 Produkthandbuch

Kenwood

Kenwood TK-3180 Bedienungs- und Wartungshandbuch

Blitz

Blitz MJ-398U Bedienungsanleitung

Utilicom

Utilicom LongRanger 2050 Bedienungsanleitung

Standart

Standart HX290UKA Bedienungsanleitung

Altronix

Altronix Pace1PTM Bedienungsanleitung

Kirisun

Kirisun PT2208 Bedienungsanleitung

ELECRAFT

ELECRAFT KX2 Bedienungsanleitung

Zodiac

Zodiac K3 Bedienungsanleitung

Assa Abloy

Assa Abloy SecureComm HKC GSM-WIFI U Bedienungsanleitung

Kenwood

Kenwood TK-2217 Bedienungsanleitung

Siemens

Siemens PSO 4000 Bedienungsanleitung

Kenwood

Kenwood TS-590SG Bedienungsanleitung

Midland

Midland G8E-BT Handbuch

ComNav

ComNav Mariner X2 Bedienungsanleitung