XtendLan XL-GFC142M Bedienungsanleitung

XL-GFC142M - G.fast Master Modem +

XL-GFC142SR - G.fast / VDSL2 / V35b Slave Modem/Router

USER’S MANUAL

Safety Warnings

For your safety, be sure to read and follow all warning notices and instructions before using the device.

DO NOT open the device or unit. Opening or removing the cover may expose you to dangerous high voltage points or other

risks. ONLYqualified service personnel can service the device. Please contact your vendor for further information.

Use ONLY the dedicated power supply for your device. Connect the power to the right plug type (AC support full range

between 100Vac and 240Vac input. 12V DC / 2A or aboveoutput).

Place connecting cables carefully so that no one will step on them or stumble over them. DO NOT allow anything to rest on

the power cord and do NOT locate the product where anyone can work on the powercord.

DO NOT install nor use your device during a thunderstorm. There may be a remote risk of electric shock from lightning.

DO NOT expose your device to dampness, dust or corrosiveliquids.

DO NOT use this product near water, for example, in a wet basement or near a swimmingpool.

Connect ONLY suitable accessories to thedevice.

Make sure to connect the cables to the correctports.

DO NOT obstruct the device ventilation slots, as insufficient air flow may harm your device.

DO NOT place items on the device.

DO NOT use the device for outdoor applications directly, and make sure all the connections are indoors or have waterproof

protection place.

Be careful when unplugging the power, because it may producesparks.

Keep the device and all its parts and accessories out of the reach ofchildren.

Clean the device using a soft and dry cloth rather than liquid or atomizers. Power off the equipment before cleaning it.

This product is recyclable. Dispose of itproperly.

Table of Contents

Chapter 1. Unpacking Information...................................................................................................................... 3

Chapter 2. Installing the Modem......................................................................................................................... 4

Chapter 3. Hardware Description...................................................................................................................... 14

Chapter 4. Configure the modem via Web managementmenu....................................................................... 21

Appendix A: Cable Requirements .................................................................................................................... 46

Appendix B: Product Specifications - Key Features & Benefits .................................................................... 50

Appendix C:Troubleshooting ........................................................................................................................... 53

This is a class A product. In a domestic environment, this product may cause radio interference in which

case the user may be required to take adequate measures.

Chapter 1. Unpacking Information

1.1 Check List

Before installing the modem, please verify the contents inside the package.

Package Contents:

Notes:

1 x Modem

1 x QR code for user’s 1. Accessory Kit: 1x Ethernet Cable, 1x Phone wire,

manual hyperlink. 1x DC12V/2A Power Adapter, 1x Powercord.

1.Please inform your dealer immediately for any missing or damaged parts. If possible, retain the carton including the

original packing materials. Use them to repack the unit in case there is a need to return for repair.

2. Do not use sub-standard power supply. Before connecting the power supply to the device, be sure to check

compliance with the specifications. The modem uses a DC 12V/2A or above Switching power supply.

Chapter 2. Installing the Modem

2.1 Hardware Installation

This chapter describes how to install the modem, and establish the network connections. The XL-GFC142SR may be

installed on any level surface (e.g. a table or shelf). However, please take note of the following minimum site

requirements before you begin.

2.2 Pre-installation Requirements

Before you start the actual hardware installation, make sure you can provide the right operating environment, including

power requirements, sufficient physical space, and proximity to other network devices that are to be connected.

Verify the following installation requirements:

Power requirements: DC 12 V / 2A orabove

The modem should be located in a cool dry place, with at least 10cm of space at the front and back for

ventilation.

Place the modem away from direct sunlight, heat sources, or areas with a high amount of electromagnetic

interference.

Check if the network cables and connectors needed for installation areavailable.

Do not install phone lines strapped together withAC power lines, or telephone office line with voice signal.

Avoid installing this device with radio amplifying stations nearby or transformer stations nearby.

2.3 General Rules

Before making any connections to the modem, please note the following rules:

Ethernet Port interface : RJ-45

All network connections to the modem Ethernet port must be made using Category 5e UTP/STP or above

for 1000 Mbps, Category 5 UTP or above for 100Mbps Category 3, 4 UTP or above for 10Mbps.

No more than 100 meters of cabling may be use between the MUX or HUB and an end node.

G.fast Port interface : RJ-11 & Terminal block combo

All network connections to the RJ-11/ terminal block(sharing port) must use 24~26 gauge with single

twisted pair phone wire.

We do not recommend the usage of the other gauge phone wire.

The RJ-11 is an 6P4C connector, two of which are wired. The modem uses the center two pins. The pin out

assignment for these connectors is presented below.

Please note that the line port is no polarity, therefore user can reverse the two wires of the phone cable

when installed. RJ-11 Pin out Assignments

Pin#

MNEMONIC

FUNCTION

Unused

Pass through

G.fast / xDSL

Pass through

Unused

2.4 Connecting the RJ-11 / RJ-45 Ports

There are two type line: 1 Terminal Block & 1 RJ-11 connector. It is used to connect with DPU Master side over asingle

pair phone wire to CPE Slave side (point to point application). (Figure 2.1)

Figure 2.1 line ports straight connection

When inserting a RJ-11 plug, make sure the tab on the

plug clicks into position to ensure that it is properly

seated.

Do not plug a RJ-11 phone jack connector into the

Ethernet port (RJ-45 port). This may damage the

modem. Instead, use only twisted-pair cables withRJ-45

connectors that conform to Ethernetstandard.

Notes:

Be sure each twisted-pair cable (RJ-45 Ethernet cable)

does not exceed 100 meters.

We advise using Category 5~7 UTP/STP cables for

making Ethernet connections to avoid any confusion or

inconvenience in the future when you attach high

bandwidth devices.

Use 24 ~ 26 gauge twisted pair phone wiring, we do not

recommend the usage of the other gauge phonewire.

Be sure phone wire has been installed before the

modems boot (before their synchronisation)

Do not connect Line port with RJ-11 and Terminal block

to two Master / Slave device

2.5 Point to Point application

First a quick overview on a complete setup of LAN extender Master/Slave LAN extender.

XL-GFC142 is a LAN extender leverages the extraordinary bandwidth promise of G.fast technology(max. 1Gbps)

(Figure 2.2)

2.5.1 Connect the XL-GFC142M (DPU Master) and the XL-GFC142SR (CPE Slave) to the Line

The objective for LAN extender is to pass high speed data over a twisted pair cable. In the setup, connect DPU Master to

CPE Slave through phone wire (24~26 AWG) or line simulator or any other hardware representation of a cable network, with

or without noise injection and crosstalk simulations.

2.5.2 Connect the XL-GFC142M (DPU Master) and the XL-GFC142SR (CPE Slave) to LAN Devices

In the setup, usually an Ethernet tester serves as a representation of the LAN side as well as a representation of the WAN(Line)

side.

2.5.3 Run Demos and Tests

The Ethernet tester may send data downstream as well as upstream. It also receives the data in order to check the integrity of the

data transmission. Different data rates can be tested under different line conditions

2.6 Internet ISP application

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere XtendLan Modem Handbücher

XtendLan

XtendLan XL-GDB102E Bedienungsanleitung

XtendLan

XtendLan G.SHDSL .bis NTU Series Bedienungsanleitung

XtendLan

XtendLan XL-GDB101V Bedienungsanleitung

XtendLan

XtendLan XL-VCF104M Bedienungsanleitung

Beliebte Modem Handbücher anderer Marken

Davicom

Davicom DM562AP Bedienungsanleitung

Zte

Zte WiMAX Bedienungsanleitung

Intelimax

Intelimax MA-2060 Bedienungsanleitung

SMC Networks

SMC Networks D3CM1604V Gebrauchs- und Pflegehandbuch

Telstra

Telstra Wi-Fi 4G Advanced Pro X Bedienungsanleitung

Thrane&Thrane

Thrane&Thrane imarsat EXPLORER 300 Bedienungsanleitung

Samsung

Samsung AceLink SAM-335A Bedienungsanleitung

Enfora

Enfora Enabler-G Kurzanleitung zur Einrichtung

iRZ

iRZ ATM2-232 Bedienungsanleitung

Zhone

Zhone 6310 Bedienungsanleitung

Paradyne

Paradyne Hotwire 7976 Bedienungsanleitung

US Robotics

US Robotics 3453C Bedienungsanleitung

MaxTech

MaxTech Plug & Play Internal Voice/FAX/Data/SVD... Bedienungsanleitung

Zte

Zte MF823 Bedienungsanleitung

Four-Faith

Four-Faith F1403 Bedienungsanleitung

Sierra Wireless

Sierra Wireless AIRLINK MP595W Bedienungsanleitung

Gemtek

Gemtek WiMAX WIXFBR-103 Bedienungsanleitung

Zoom

Zoom 1070 Series Bedienungsanleitung