XtendLan XL-VCF104M Bedienungsanleitung



XL-VCF104M (CO)

XL-VCF104S (CPE)

VDSL2 CO/CPE modem

User’s Guide

ADSL-like long reach (LR) performance: ADSL-like long reach performance is one of the key advantages of VDSL2.

systems, unlike VDSL1 systems, are not limited to short loops or MTU/MDUs only, but can also be used for medium

VDSL2 Point to Point Solution

VDSL2 (Very-High-Bit-Rate Digital Subscriber Line 2, ITU-T G.993.2 Standard) is an access technology that exploits the

existing infrastructure of copper wires that were originally deployed for POTS services. It can be deployed from central

LR-VDSL2 enabled systems are capable of supporting speeds of around 1-4 Mbit/s (downstream) over distances of 4 to

interactive gaming, VDSL2 enables operators and carriers to gradually, flexibly, and cost efficiently upgrade existing

ITU-T G.993.2 VDSL2 is the newest and most advanced standard of DSL broadband wireline communications. Designed

ITU-T G.993.2 (VDSL2) is an enhancement to G.993.1 VDSL that permits the transmission of asymmetric and symmetric

to support the wide deployment of Triple Play services such as voice, video, data, high definition television (HDTV) and

VDSL2 deteriorates quickly from a theoretical maximum of 250 Mbit/s at 'source' to 100 Mbit/s at 0.5 km and 50 Mbit/s at

5 km, gradually increasing the bit rate up to symmetric 100Mbit/s as loop-length shortens. This means that VDSL2-based

1 km, but degrades at a much slower rate from there, and still outperforms VDSL. Starting from 1,6 km its performance is

(Full-Duplex) aggregate data rates up to 200 Mbit/s on twisted pairs using a bandwidth up to 30 MHz.

offices, from fibre-fed cabinets located near the customer premises, or within buildings.

xDSL-infrastructure.

range applications.

equal to ADSL2+.

CONTENT

1.Unpacking Information ................................................................................... 3

Check List.......................................................................................................... 3

2. Installation ..................................................................................................... 4

Hardware Installation......................................................................................... 4

2.1 Pre-installation Requirements.................................................................4

General Rules...............................................................................................5

Connecting the VDSL2 CO&CPE Modem ....................................................5

3. Hardware Description.................................................................................... 7

4. Setup the VDSL2 CO&CPE Modem by Web Browser................................ 10

4.1 Login. ....................................................................................................10

4.2 Select the Menu Level .......................................................................... 11

4.3 Select Advanced Setup.........................................................................12

4.4 Select LAN............................................................................................13

5. Building a VDSL2 System .................................................................………16

5.1 Connect the CPE and the CO to the Line.............................................16

5.2 Connect the CPE and the CO to LAN Devices.....................................17

5.3 Run Demos and Tests...........................................................................17

6. Operating the VDSL2 System ..................................................................... 18

6.1 Configuration Settings ..........................................................................18

6.2 Status Displays .....................................................................................26

7. Configuration Interface of the Router .................................................. …….31

7.1 Logging on to the VDSL2 CO&CPE Modem ........................................31

7.2 Configuration Menu for Administrators .................................................32

Appendix A: Product Features & Specification................................................ 68

Appendix B: Compliance and Safety Information............................................ 70

1.Unpacking Information

Check List

Carefully unpack the package and check its contents against the checklist.

Package Contents

●

VDSL2 Modem (VDSL2 CO Modem / VDSL2 CPE Modem)

●

Two plastic feet

●

User’s Manual

●

AC to DC 12V Power Adapter

●

RJ-45 cable

●

RJ-11 cable

Please inform your dealer immediately for any missing, or damaged parts. If possible, retain the carton,

including the original packing materials, Use them to repack the unit in case there is a need to return for

repair.

2. Installation

Hardware Installation

This chapter describes how to install the VDSL2 CO&CPE MODEM and establishes network connections. You

may install the VDSL2 CO&CPE MODEM on any level surface (e.g, a table or shelf). However, please take note of

the following minimum site requirements before you begin.

2.1 Pre-installation Requirements

Before you start actual hardware installation, make sure you can provide the right operating environment, including

power requirements, sufficient physical space, and proximity to other network devices that are to be connected.

Verify the following installation requirement:

●

Power requirements: DC12V/1A or above.

●

The VDSL2 CO&CPE MODEM should be located in a cool dry place, with at least 10cm/4in of space at the front

and back for ventilation.

●

Place the VDSL2 CO&CPE MODEM out of direct sunlight, and away from heat sources or areas with a high

amount of electromagnetic interference.

●

Check if network cables and connectors needed for installation are available

General Rules

Before making any connections to the VDSL2 CO&CPE MODEM, note the following rules:

●

Ethernet Port (RJ-45)

All network connections to the Modem Ethernet port must be made using Category 5 UTP for 100Mbps;

Category 3,4 UTP for 10Mbps

No more than 100 meters of cabling may be use between the MUX or HUB and an end node.

●

Phone Port (RJ-11)

All Phone set connections to the RJ-11 Port made using 24~26 Gauge phone wiring.

Connecting the VDSL2 CO&CPE MODEM

The VDSL2 CO&CPE MODEM can be controlled by a PC, henceforth, called the "Control PC". For this purpose, you

needa PC with an Ethernet network interface and a DB-9 RS232 serial interface. Two programs are required: A Web

browser is mandatory and a terminal program should be available optionally. The board has several connectors.

4 Ethernet RJ45 jacks (connect LAN devices to route); the Auto MDIX feature of the ports switches automatically

between MDI and MDI-X (MDI = Media Dependant Interface), therefore straight Ethernet cables can be used.

2 x RJ11 jack (LINE Port is for connects VDSL client side to Line Interface, Phone port is for connects phone set or

FAX machine)

1 x Console port (monitoring, access to operating system via shell for firmware downloads, starting drivers and web etc.,)

1 Power Supply (as described above)

Figure 2.1 VDSL2 Point to Point application

3. Hardware Description

This section describes the important parts of the VDSL2 CO&CPE MODEM. It features the front indicators and rear

connectors.

Front Indicators

The following figure shows the front panel.

Figure Chapter 3.1 VDSL2 CO Modem

Figure Chapter 3.2 VDSL2 CPE Modem

Six LED indicators.

At a quick glance of the front panel, it will be easy to tell if the Modem has power, signal from its Ethernet

RJ-45 port or there is phone line signal RJ-11port

Front Indicators

LED Description and Operation

The Modem has three LED indicators.

LEDs Status Descriptions

PWR

(Ready LED)

Steady

Green

It will light up (ON) to show that the product is

power good, and system reset OK.

E1~E4

(Ethernet

LED)

Steady

Green

Flashing

(LINK/ACT)

Each RJ-45 station port on the Ethernet is

assigned an LED light for monitoring port “Good

Linkage”. LED is normally OFF after the powe

on operation, but will light up steadily to show

good linkage and flashing to show data

transmission.

Link

(VDSL LED)

Steady

Green

RJ11 station port on the VDSL is assigned an

LED light for monitoring port “Good Linkage”.

LED is normally OFF after the power on

operation, but will light up steadily to show good

linkage.

Rear Panel

The following figure shows the rear connectors

Figure Chapter 3.3 Rear Connectors

VDSL2 CO&CPE MODEM Rear Connectors

Connectors Description Type

Line For connecting to the VDSL Modem Using

a RJ-11 cable

RJ-11

Phone For connecting to the telephone or FaxISDN

Modem RJ-11

E1~E4 For connecting to a Ethernet equipped device RJ-45

Console port For connecting to PC with RS-232 serial

port over a D-SUB Cable

RS-232

Power On

1. Check the adapter is properly connected.

2. Verify the power LED is steadily on.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere XtendLan Modem Handbücher

XtendLan

XtendLan XL-GFC142M Bedienungsanleitung

XtendLan

XtendLan G.SHDSL .bis NTU Series Bedienungsanleitung

XtendLan

XtendLan XL-GDB101V Bedienungsanleitung

XtendLan

XtendLan XL-GDB102E Bedienungsanleitung

Beliebte Modem Handbücher anderer Marken

Davicom

Davicom DM562AP Bedienungsanleitung

Zte

Zte WiMAX Bedienungsanleitung

Intelimax

Intelimax MA-2060 Bedienungsanleitung

SMC Networks

SMC Networks D3CM1604V Gebrauchs- und Pflegehandbuch

Telstra

Telstra Wi-Fi 4G Advanced Pro X Bedienungsanleitung

Thrane&Thrane

Thrane&Thrane imarsat EXPLORER 300 Bedienungsanleitung

Samsung

Samsung AceLink SAM-335A Bedienungsanleitung

Enfora

Enfora Enabler-G Kurzanleitung zur Einrichtung

iRZ

iRZ ATM2-232 Bedienungsanleitung

Zhone

Zhone 6310 Bedienungsanleitung

Paradyne

Paradyne Hotwire 7976 Bedienungsanleitung

US Robotics

US Robotics 3453C Bedienungsanleitung

MaxTech

MaxTech Plug & Play Internal Voice/FAX/Data/SVD... Bedienungsanleitung

Zte

Zte MF823 Bedienungsanleitung

Four-Faith

Four-Faith F1403 Bedienungsanleitung

Sierra Wireless

Sierra Wireless AIRLINK MP595W Bedienungsanleitung

Gemtek

Gemtek WiMAX WIXFBR-103 Bedienungsanleitung

Zoom

Zoom 1070 Series Bedienungsanleitung