XtendLan XL-ICA-206M1IR Bedienungsanleitung

Quick Start Guide

Version 1.0.0

XL-ICA-206M1IR

Welcome

Thank you for purchasing our IP camera!

This quick start guide is designed to be a reference tool for your system.

Please keep this start guide well for future reference.

Please open the accessory bag to check the items one by one in accordance with the list below.

Contact your local retailer ASAP if something is missing or damaged in the bag.

Before your operation please read the following instructions carefully.

1．Electrical safety

All installation and operation here should conform to your local electrical safety codes.

The power shall conform to the requirement in the SELV (Safety Extra Low Voltage) and the Limited

power source is rated 12V DC in the IEC60950-1.This series product supports PoE too. Please note:

Do not connect these two power supplying sources to the device at the same time; it may result

in device damage!

We assume no liability or responsibility for all the fires or electrical shock caused by improper handling

or installation.

We are not liable for any problems caused by unauthorized modification or attempted repair.

2．Transportation security

Heavy stress, violent vibration or water splash are not allowed during transportation, storage and

installation.

3．Installation

Do not apply power to the camera before completing installation.

Please install the proper power cut-off device during the installation connection.

Always follow the instruction guide the manufacturer recommended.

4．Qualified engineers needed

All the examination and repair work should be done by the qualified service engineers.

We are not liable for any problems caused by unauthorized modifications or attempted repair.

5．Environment

This series IP camera should be installed in a cool, dry place away from direct sunlight, inflammable,

explosive substances and etc.

Please keep it away from the electromagnetic radiation object and environment.

Please make sure the CCD (CMOS) component is out of the radiation of the laser beam device.

Otherwise it may result in CCD (CMOS) optical component damage.

Please keep the sound ventilation.

Do not allow the water and other liquid falling into the camera.

Thunder-proof device is recommended to be adopted to better prevent thunder.

The grounding studs of the product are recommended to be grounded to further enhance the reliability

of the camera.

6. Daily Maintenance

Please shut down the device and then unplug the power cable before you begin daily maintenance

work.

Do not touch the CCD (CMOS) optic component. You can use the blower to clean the dust on the lens

surface.

Always use the dry soft cloth to clean the device. If there is too much dust, please use the water to

dilute the mild detergent first and then use it to clean the device. Finally use the dry cloth to clean the

device.

Please put the dustproof cap to protect the CCD (CMOS) component when you do not use the camera.

7. Accessories

Be sure to use all the accessories recommended by manufacturer.

Before installation, please open the package and check all the components are included.

Contact your local retailer ASAP if something is broken in your package.

Accessory Name Amount

IPC Unit 1

Quick Start Guide 1

CD 1

Installation Accessories Bag 1

iii

Table of Contents

1Structure ......................................................................................................................................1

1.1 Components..................................................................................................................1

1.2 Framework and Dimension.........................................................................................1

2Device Installation ......................................................................................................................3

2.1 Installation Steps ..........................................................................................................3

2.2 Restore Factory Default Setup Introduction.............................................................5

3Quick Configuration Tool...........................................................................................................6

3.1 Overview........................................................................................................................6

3.2 Operation .......................................................................................................................6

4Web Operation............................................................................................................................9

4.1 Network Connection.....................................................................................................9

4.2 Login and Logout..........................................................................................................9

5FAQ ............................................................................................................................................12

Appendix Toxic or Hazardous Materials or Elements ...............................................................13

1Structure

1.1 Components

You can refer to the following figure for multiple-function combination cable information. See Figure

1-1.

Figure 1-1

Please refer to the following sheet for detailed information.

Port Name Function Note

Port 4 Network port Connect to standard Ethernet cable.

Port 5 DC 12V

power Power input port. Input DC 12V.

1.2 Framework and Dimension

Component Component Name

Component 1 Device lens

Component 2 Dome body

Component 3 Dome enclosure

Please refer to the following two figures for dimension information. The unit is mm. See Figure 1-2 and

Figure 1-3.

Figure 1-2

Figure 1-3

2Device Installation

2.1 Installation Steps

Important

Before the installation, please make sure the installation environments can at least support 3x weight

of the camera.

Please follow the steps listed below to install the device. Please refer to Figure 2-1 for reference.

Step 1

Turn clockwise to remove the decoration ring from the snap joints.

Step 2

Please take the installation position map in the accessories bag, and then paste it on the ceiling or the

wall according to your monitor area requirements. Draw and then dig three plastic expansion bolts

holes in the installation surface and then insert three expansion bolts in the holes. Secure these three

bolts firmly. Please draw the cable out from the cable exit when you install the device.

Step 3

Adjust the device installation pedestal to the proper position and then line up the three screw holes in

the device pedestal to the three plastic expansion bolt holes in the installation position. Put the three

self-tapping screws in the three plastic expansion bolts firmly. Loosen the M3X8 cross recessed pan

head slot screw of the pedestal to unfasten the preforming. (Do not remove, loosen a little bit will be

OK.). Adjust the lens to the proper monitor angle and then use the original preforming to turn the M3X8

cross recessed pan head slot screw back.

Step4

Line up the three spigots of the decoration ring to the jags from the bottom to the top and then turn

clockwise until you hear a clear sound ”KA”. Now the installation is complete.

Figure 2-1

Important

Please pay attention to the dome camera direction when you are installing. Please refer to the

following figure for detailed information. See Figure 2-2.

Figure 2-2

Note

This series product supports two cable exits. One is from the bottom and the other is from the side.

Please refer to the following figure for cable exit from the side information.

Figure 2-3

Please earth the GND port of the device to enhance the device reliability. The GND port is near the

cable exit port on the rear of the dome. The GND screw uses the M2X5 pan screw.

Figure 2-4

2.2 Restore Factory Default Setup Introduction

Important

Please use RESET button when device is running.

Step1

Please refer to step1 and step2 in chapter 2.1to loose the dome body. Push a little bit; you can take

the dome body from the gland cover.

Step2

Take the dome body out and then turn the top cover hard to remove.

Step3

Slightly press the RESET button to complete the reset function. See Figure 2-5.

Step4

Turn the top cover back to the original position. Please make sure it reaches the original position,

otherwise it may result in water leakage!

Step5

Put the dome back to the gland cover. Please refer to step4 in chapter 2.1 to install the decoration ring

back.

Figure 2-5

3Quick Configuration Tool

3.1 Overview

Quick configuration tool can search current IP address, modify IP address. At the same time, you can

use it to upgrade the device.

Please note the tool only applies to the IP addresses in the same segment.

3.2 Operation

Double click the “ConfigTools.exe”icon, you can see an interface is shown as in Figure 3-1.

In the device list interface, you can view device IP address, port number, subnet mask, default

gateway, MAC address and etc.

Figure 3-1

Select one IP address and then right click mouse, you can see an interface is shown as in Figure 3-2.

Note:

You can set the IP address, subnet mask and gateway for the IPC and PC. Please note IPC IP

address and PC IP address shall be in the same network segment if there is no router. IPC default IP

address is 192.168.1.108. If there is a router, please set the corresponding gateway and subnet mask.

The factory default user name is admin and password is admin. For security reasons, please modify

your password after you first login.

For detailed WEB operation, please refer to the IPC Web Operation Manual in the resource CD.

Inhaltsverzeichnis

Andere XtendLan Sicherheitskamera Handbücher

XtendLan

XtendLan XL-ICA-106M3 Bedienungsanleitung

XtendLan

XtendLan XL-ICA-107M1C Bedienungsanleitung

XtendLan

XtendLan SDOMEOAT2-SD332 Bedienungsanleitung

XtendLan

XtendLan OUTIRDVS620FR-42 Bedienungsanleitung

XtendLan

XtendLan PEDOMEOIR48023SD Bedienungsanleitung

XtendLan

XtendLan XL-ICA562M1CIR Bedienungsanleitung

XtendLan

XtendLan Speed Dome Bedienungsanleitung

XtendLan

XtendLan XL-ICA301A Bedienungsanleitung

XtendLan

XtendLan XL-ICA-641M2 Bedienungsanleitung

XtendLan

XtendLan XL-ICA-361M3CP Bedienungsanleitung

XtendLan

XtendLan XL-ICA-661M1CP Bedienungsanleitung

XtendLan

XtendLan SDOMEOAT-57030SD Bedienungsanleitung

XtendLan

XtendLan HDC-SDOMEO51MIR-B Bedienungsanleitung

XtendLan

XtendLan XL-ICA-371M2 Bedienungsanleitung

XtendLan

XtendLan ABOX56022 Bedienungsanleitung

XtendLan

XtendLan SDOMEOAT2-SD310 Bedienungsanleitung

XtendLan

XtendLan XL-ICA-H660-SC110 Bedienungsanleitung

XtendLan

XtendLan XL-ICA-306M3 Bedienungsanleitung

XtendLan

XtendLan XL-ICA-306M1 Bedienungsanleitung

XtendLan

XtendLan XL-ICA-206M2IR-36 Bedienungsanleitung

XtendLan

XtendLan SDOMEO4802701 Bedienungsanleitung

XtendLan

XtendLan SDOMEOIR6-CM10 Bedienungsanleitung

XtendLan

XtendLan SDOMEOATM Bedienungsanleitung

XtendLan

XtendLan XL-ICA-206M2T-M39 Bedienungsanleitung

Beliebte Sicherheitskamera Handbücher anderer Marken

Okina USA

Okina USA SIR36-870VF650LP Bedienungsanleitung

Divio

Divio NDR155PA Bedienungsanleitung

Easy Access

Easy Access EasyGuard Bedienungsanleitung

Vivotek

Vivotek FD9389-EHV-v2 Bedienungsanleitung

TUYA

TUYA COSMO W2 Bedienungsanleitung

Eusso

Eusso UNC7500-IR Einrichtungshandbuch

urmet domus

urmet domus 1096/204 Bedienungsanleitung

VC VC20 series Bedienungsanleitung

Axis

Axis Q1614 Bedienungsanleitung

ieGeek

ieGeek DD201 Bedienungsanleitung

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Bedienungsanleitung

Vicon

Vicon V662-D-1 Betriebsanleitung

Grundig

Grundig GCH-K0274P Bedienungsanleitung

Lorex

Lorex VANTAGE LBC7032 Bedienungsanleitung

4xem

4xem WPT Bedienungsanleitung

Samsung

Samsung SCV-3082 Bedienungsanleitung

Vitek

Vitek VTC-C544 Bedienungsanleitung

Lumens

Lumens VC-A50PNW Bedienungsanleitung