Xtreme Power Conversion P91g Series Leitfaden

P91 / P91g Lead Acid Online UPS

1000VA, 2000VA, 3000VA Models

User & Installation Manual

P91 Lead Acid 2U User’s Manual Uninterruptible Power Supply

Table of Contents

1. Important Safety Warning ..........................................................................................................1

1-1. Transportation........................................................................................................................... 1

1-2. Preparation ............................................................................................................................... 1

1-3. Installation ................................................................................................................................ 1

1-4.

Operation

.................................................................................................................................. 2

1-5. Maintenance, service and faults............................................................................................... 2

2. Installation and

tup

.................................................................................................................4

2-1. Rear panel view......................................................................................................................... 4

2-2. Operating principle ................................................................................................................... 6

2-3. Install the

S........................................................................................................................... 6

2-4. Setup the UPS ........................................................................................................................... 7

2-5. Battery Replacement .............................................................................................................. 11

2-6. Battery Kit

Assem

............................................................................................................... 12

3. Operations ............................................................................................................................... 15

3-1. Button operation..................................................................................................................... 15

3-2. LCD Panel ................................................................................................................................ 15

3-3. Audible Alarm ......................................................................................................................... 16

3-4. LCD display wordings index..................................................................................................... 17

3-5. UPS Setting.............................................................................................................................. 18

3-6. Operating Mode Description .................................................................................................. 22

3-7. Faults Reference Code ............................................................................................................ 23

3-8. Warning indicator ................................................................................................................... 23

Troubleshooting

....................................................................................................................... 24

5. Storage and M

aint

nce......................................................................................................... 25

Specifications

........................................................................................................................... 26

7. Obtaining Service ..................................................................................................................... 28

8. Xtreme Power Conversion Limited W

anty

............................................................................. 29

9. Xtreme Power Conversion Load Protection Policy ..................................................................... 31

Xtreme Power Conversion Corporation

P91 Lead Acid 2U User’s Manual

Uninterruptible Power Supply

Xtreme Power Conversion Corporation

Page 1

1. Important Safety Warning

SAVE THESE INSTRUCTIONS - This manual contains important instructions that should be followed

during installation and maintenance of the UPS and batteries.

Please comply with all warnings and operating instructions in this manual strictly. Do not operate this

unit before reading through all safety information and operating instructions carefully.

1-1. Transportation

Please transport the UPS system only in the original package to protect against shock and

impact.

1-2. Preparation

Condensation may occur if the UPS system is moved directly from cold to warm

environment. The UPS system must be absolutely dry before being installed. Please allow

at least two hours for the UPS system to acclimate to the environment.

Do not install the UPS system near water or in moist environments.

Do not install the UPS system where it would be exposed to direct sunlight or near heater.

Do not block ventilation holes in the UPS housing.

1-3. Installation

Do not connect appliances or devices which would overload the UPS system (e.g. laser

printers) to the UPS output sockets.

Place cables in such a way that no one can step on or trip over them.

Do not connect domestic appliances such as hair dryers to UPS output sockets.

The UPS can be operated by any individuals with no previous experience.

Connect the UPS system only to an earthed shockproof outlet which must be easily

accessible and close to the UPS system.

Please use only VDE-tested, CE-marked (for P91g models or UL-marked for P91 models)

mains cable (e.g. the mains cable of your computer) to connect the UPS system to the

building wiring outlet (shockproof outlet).

Please use only VDE-tested, CE-marked (for P91g models or UL-marked for P91 models)

power cables to connect the loads to the UPS system.

When installing the equipment, it should ensure that the sum of the leakage current of the

UPS and the connected devices does not exceed 3.5mA.

Temperature Rating - Units are considered acceptable for use in a maximum ambient of

40°C (104°F).

For Pluggable Equipment - The socket-outlet shall be installed near the equipment and shall

be easily accessible.

CAUTION: The unit is heavy. Lifting the unit requires a minimum of two people.

Batteries with minimum case flame rating V-2 are intended for use in a computer room as

defined in the Standard for the Protection of Information Technology Equipment,

ANSI/NFAP 75. Batteries with case flame rating HB are not intended for use in a computer

room. (US installations only.)

P91 Lead Acid 2U User’s Manual

Uninterruptible Power Supply

Xtreme Power Conversion Corporation

Page 2

1-4. Operation

Do not disconnect the mains cable on the UPS system or the building wiring outlet

(shockproof socket outlet) during operations since this would cancel the protective

earthing of the UPS system and of all connected loads.

The UPS system features its own, internal current source (batteries). The UPS output

sockets or output terminals block may be electrically live even if the UPS system is not

connected to the building wiring outlet.

In order to fully disconnect the UPS system, first press the OFF/Enter button to turn off the

unit.

Prevent fluids or other foreign objects from inside of the UPS system.

The EPO and USB circuits are an IEC 60950-1 safety extra low voltage (SELV) circuit. This

circuit must be separated from any hazardous voltage circuits by reinforced insulation.

1-5. Maintenance, service and faults

The UPS system operates with hazardous voltages. Repairs may be carried out only by

qualified maintenance personnel.

Caution - risk of electric shock. Even after the unit is disconnected from the mains (building

wiring outlet), components inside the UPS system are still connected to the battery and

electrically live and dangerous.

Before carrying out any kind of service and/or maintenance, disconnect the batteries and

verify that no current is present and no hazardous voltage exists in the terminals of high

capability capacitor such as BUS-capacitors.

To avoid electrical shock, turn off the unit and unplug it form the AC power source before

servicing the battery

Only persons adequately familiar with batteries and with the required precautionary

measures may replace batteries and supervise operations. Unauthorized persons must be

kept well away from the batteries.

Caution - risk of electric shock. The battery circuit is not isolated from the input voltage.

Hazardous voltages may occur between the battery terminals and the ground. Before

touching, please verify that no voltage is present!

Caution - Do not dispose of batteries in a fire. The batteries may explode.

Caution - Do not open or mutilate batteries. Released electrolyte is harmful to the skin and

eyes. It may be toxic.

A battery can may cause a risk of electrical shock and high short-circuit current. The

following precautions should be observed when working on batteries:

a) Remove watches, rings, or other metal objects.

b) Use tools with insulated handles.

c) Wear rubber gloves and boots.

d) Do not lay tools or metal parts on top of batteries.

e) Disconnect charging source prior to connecting or disconnecting

battery

terminals.

f) Determine if battery is inadvertently grounded. If inadvertently grounded,remove source

from ground. Contact with any part of a grounded battery can

sul

in electrical shock.

The likelihood of such shock can be reduced if such grounds are removed during

installation and maintenance.

P91 Lead Acid 2U User’s Manual

Uninterruptible Power Supply

Xtreme Power Conversion Corporation

Page 3

When changing batteries, install the same number and same type of batteries or battery

packs.

Please replace the fuse only with the same type and amperage in order to avoid fire

hazards.

Do not dismantle the UPS system.

WARNING: This is a category C2 UPS product. In a residential environment, this product

may cause radio interference, in which case the user many be required to take additional

measures. (only for CE models)

NOTE: This equipment has been tested and found to comply with the limits for a Class A

digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference when the equipment is operated in a

commercial environment. This equipment generates, uses, and can radiate radio frequency

energy and, if not installed and used in accordance with the instruction manual, may cause

harmful interference to radio communications. Operation of this equipment in a residential

area is likely to cause harmful interference in which case the user will be required to correct

the interference at his own expense.

WARNING: Changes or modifications not expressly approved by the party responsible for

compliance could void the user's authority to operate the equipment.

P91 Lead Acid 2U User’s Manual

Uninterruptible Power Supply

Xtreme Power Conversion Corporation

Page 4

2. Installation and setup

NOTE: Before installation, please inspect the unit. Be sure that nothing inside the package is damaged.

Please keep the original package in a safe place for future use.

2-1. Rear panel view

P91g models:

1500 Model 2000 Model

3000 Model

P91 models:

1000/1500 Model 2000 Model

3000 Model

1. Programmable outlets: connect to non-critical loads.

2. Output receptacles: connect to mission-critical loads.

3. AC input

4. Network/Fax/Modem surge protection

P91 Lead Acid 2U User’s Manual

Uninterruptible Power Supply

Xtreme Power Conversion Corporation

Page 5

5. USB communication port

6. RS-232 communication port

7. SNMP intelligent slot

8. Emergency power off function connector (EPO)

9. External battery connection

10. Output circuit breaker

P91 Lead Acid 2U User’s Manual

Uninterruptible Power Supply

Xtreme Power Conversion Corporation

Page 6

DC-to-DC

Converter

Battery

2-2. Operating principle

The operating principle of the UPS is shown as below

Input

Output

EMI/RFI

Filters

Rectifier

/PFC

Dynamic

Bypass

Inverter

Battery

Charger

The UPS is composed of mains input, EMI/RFI filters, rectifier/PFC, inverter, battery charger, DC-to-DC

converter, battery, dynamic bypass and UPS output.

2-3. Install the UPS

This UPS can be either displayed on the desk or mounted in the 19”rack chassis. Please choose

proper installation to position this UPS.

Rack-mount Installation

Step 1 Step 2

UPS

wer Installation

Step 1 Step 2 Step 3

P91 Lead Acid 2U User’s Manual

Uninterruptible Power Supply

Xtreme Power Conversion Corporation

Page 7

Tower Installation with battery pack

Step 1 Step

2-4. Setup the UPS

Before installing the UPS, please read below to select proper location to install UPS.

1. UPS should be placed on the flat and clean surface. Place it in an area away from vibration, dust,

humidity, high temperature, flammable liquids, gas, corrosive and conductive contaminants.

Install the UPS indoors in a clean environment, where it is away from window and door. Maintain

minimum clearance of 100mm in the bottom of the UPS to avoid dust and high temperature.

2. Place UPS:

It’s equipped with fan for cooling. Therefore, place the UPS in a well-ventilated area. It’s required to

maintain minimum clearance of 100mm in the front of the UPS and 300mm in the back and two sides

of the UPS for heat dissipation and easy-maintenance.

Step 1: External battery connection

For safety consideration, the UPS is shipped out from factory without connecting battery wires.

Before connecting to external batteries, it’s required to have the internal battery wire disconnected.

Follow the below steps to make external battery connection.

1. Turn off UPS and remove power plug from the mains.

2. Remove front panel and disconnect internal battery wire.

P91 Lead Acid 2U User’s Manual

Uninterruptible Power Supply

Xtreme Power Conversion Corporation

Page 8

3. Remove the cover of the external battery connector by using a screwdriver.

4. Plug the battery cable into the external battery connector of the UPS and

the battery pack(s).

Note: If you have multiple battery packs available, connect them serially. An example is shown

in the diagram below (connecting the second battery connector of the first battery pack to the

first battery connector of the second battery pack).

UPS Battery

pack #1

Battery

pack #2

5. Stabilize the connector to the UPS and the battery pack(s) by fixing screws as shown below

diagram.

6. Connect internal battery connector and put the front panel back to the unit.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Xtreme Power Conversion UPS Handbücher

Xtreme Power Conversion

Xtreme Power Conversion Pure Sine Wave Series Leitfaden

Xtreme Power Conversion

Xtreme Power Conversion M90U Leitfaden

Xtreme Power Conversion

Xtreme Power Conversion P90L-ISO6MB Leitfaden

Xtreme Power Conversion

Xtreme Power Conversion NXRi-6KL Leitfaden

Xtreme Power Conversion

Xtreme Power Conversion P91c-1000 Leitfaden

Xtreme Power Conversion

Xtreme Power Conversion M90 Bedienungsanleitung

Xtreme Power Conversion

Xtreme Power Conversion P90g Series Leitfaden

Xtreme Power Conversion

Xtreme Power Conversion XVT 600VA Leitfaden

Xtreme Power Conversion

Xtreme Power Conversion A60-550 Leitfaden

Xtreme Power Conversion

Xtreme Power Conversion XPRT-6kVA Leitfaden

Xtreme Power Conversion

Xtreme Power Conversion S70 Line?Interactive Leitfaden

Xtreme Power Conversion

Xtreme Power Conversion P80g Leitfaden

Xtreme Power Conversion

Xtreme Power Conversion P90-BP36 Leitfaden

Xtreme Power Conversion

Xtreme Power Conversion 1000VA Leitfaden

Xtreme Power Conversion

Xtreme Power Conversion P91 Bedienungsanleitung

Xtreme Power Conversion

Xtreme Power Conversion XPRT 6/10KVA Leitfaden

Xtreme Power Conversion

Xtreme Power Conversion P90 1000VA Leitfaden

Xtreme Power Conversion

Xtreme Power Conversion 700VA Leitfaden

Xtreme Power Conversion

Xtreme Power Conversion XVT 600VA Bedienungsanleitung

Xtreme Power Conversion

Xtreme Power Conversion M90S Series Bedienungsanleitung

Xtreme Power Conversion

Xtreme Power Conversion 800VA P80 Series Leitfaden

Xtreme Power Conversion

Xtreme Power Conversion P80 Bedienungsanleitung

Xtreme Power Conversion

Xtreme Power Conversion XST?400 Bedienungsanleitung

Xtreme Power Conversion

Xtreme Power Conversion NXTi 3P-3P Leitfaden

Beliebte UPS Handbücher anderer Marken

Pylontech

Pylontech Victron & Pylontech US5000 Bedienungsanleitung

Tecnoware

Tecnoware EVO DSP PLUS MM 6.8 Bedienungsanleitung

Mecer

Mecer ME-1000-WTU Bedienungsanleitung

Mustek

Mustek PowerMust 530(B) Plus Installations- und Betriebshandbuch

Emerson

Emerson Liebert NXL series Bedienungsanleitung

MAKELSAN

MAKELSAN BOXER SERIES Bedienungsanleitung

Block

Block PC-0524-400-0 Bedienungsanleitung

CyberPower

CyberPower CP585LCD Bedienungsanleitung

Eaton

Eaton 3S Montageanleitung

CyberPower

CyberPower Office Tower Series UPS 1000 Bedienungsanleitung

CyberPower

CyberPower BM100 Bedienungsanleitung

Best Power

Best Power 610 Bedienungsanleitung

Best Power

Best Power Unity/I UT3K Bedienungsanleitung

Mustek

Mustek PowerMust 400 Offline Bedienungsanleitung

Xantrex

Xantrex Trace 512 UR-UPS Bedienungsanleitung

Forza

Forza SL-1501UL Bedienungsanleitung

LEGRAND

LEGRAND keor 310081 Bedienungsanleitung

ABB

ABB Conceptpower DPA 500 Bedienungsanleitung