Xylem ProSwap 610224-01 Bedienungsanleitung

ProSwap Logger

User Manual

1-PORT TEMPERATURE/DEPTH SONDE

USER MANUAL

ITEM# 610224-01

REVISION A

The information contained in this manual is subject to change without notice.

Effort has been made to make the information in this manual complete, accurate, and current.

The manufacturer shall not be held responsible for errors or omissions in this manual.

Consult YSI.com for the most up-to-date version of this manual.

NOTICE: Indicates a situation which, if not avoided, may cause damage to the instrument

Thank you for purchasing a YSI ProSwap Logger. This manual covers setup, operation, and functionality of the sonde,

handheld, and sensors.

Product Components

Carefully unpack the instrument and accessories and inspect for damage. If any parts or materials are damaged,

contact YSI Customer Service at 800-897-4151 (+1 937 767-7241) or the authorized YSI distributor from whom the

instrument was purchased.

Technical Support

Telephone: 800 897 4151 (USA)

+1 937 767 7241 (Globally) Monday through Friday, 8:00 AM to 5:00 ET

Fax: +1 937 767 9353 (orders)

Email: [email protected]

YSI.com

Safety Information

Please read this entire manual before unpacking, setting up or operating this equipment. Pay attention to all

precautionary statements. Failure to do so could result in serious injury to the operator or damage to the equipment.

Make sure that the protection provided by this equipment is not impaired. Do not use or install this equipment in any

manner other than that speciﬁed in this manual.

The manufacturer is not responsible for any damages due to misapplication or misuse of this product including,

without limitation, direct, incidental and consequential damages, and disclaims such damages to the full extent

permitted under applicable law. The user is solely responsible to identify critical application risks and install

appropriate mechanisms to protect processes during a possible equipment malfunction.

Precautionary Symbols

NOTE: Information that requires special emphasis

WARNING: Indicates a potentially or imminently hazardous situation which, if not avoided, could result in death

or serious injury

CAUTION: Indicates a potentially hazardous situation that may result in minor or moderate injury

When viewing this document as an AdobeTM PDF, hovering your cursor over

certain phrases will bring up the ﬁnger-point icon. Clicking elements of the

Table of Contents, website URLs, or references to certain sections will take you

automatically to those locations.

THIS IS AN

INTERACTIVE

DOCUMENT

TABLE OF CONTENTS

1. Introduction

1.1 ProSwap Logger Overview

1.2 ProSwap Logger Contents

1.3 ProSwap Logger Power Supply

2. Setup

2.1 Sensor Installation and Removal

2.2 Sensor Guard Installation

2.3 Connection to Handheld

2.4 Connection to Kor Software

3. ProDIGITAL Handheld Operation

3.1 Handheld Keypad

3.2 Handheld Startup and Navigation

3.3 Run Screen

3.4 System Menu

3.5 Probe Menu

3.6 Calibration Menu

3.7 File Menu

4. Sensors, Calibration, and Maintenance

4.1 Calibration Setup

4.2 Calibration Screen

4.3 Temperature Sensor

4.4 Depth Sensor

4.5 Conductivity Sensor

4.6 Dissolved Oxygen Sensor

4.7 pH and pH/ORP Sensors

4.8 Ion Selective Electrodes

4.9 Turbidity Sensor

4.10 Total Algae Sensors

4.11 Handheld Barometer

5. Kor Software

5.1 System Requirements

5.2 Software and Driver Installation

5.3 Connection to Kor Software

5.4 Kor Software Home Screen

5.5 File Menu

5.6 Calibration Menu

5.7 ProDIGITAL Handheld Menu

5.8 Deployment Menu

5.9 Site Menu

5.10 Live Data Menu

5.11 Recorded Data Menu

5.12 Instrument and Sensor Menu

6. Accessories

6.1 ProDIGITAL Handheld

6.2 ProSwap Logger Power Pack

6.3 ProDIGITAL USB Adapter

6.4 Desiccant Cartridge

6.5 Flying Lead Adapter

7. Signal Output

7.1 SDI-12 Setup

7.2 SDI-12 Output Conﬁguration

7.3 SDI-12 Interface Basics

7.4 SDI-12 Parameter List

8. Safety and Support

8.1 Lithium-Ion Battery Precautions

8.2 Service Information

8.3 Technical Support

8.4 Declaration of Conformity

8.5 Warranty

Section 1

Introduction

This section will cover the ProSwap Logger speciﬁcations, sonde contents, power supply,

and introduce some relevant accessories.

Introduction

1.1 ProSwap Logger Overview

The ProSwap Logger is a multiparameter instrument that collects water quality data. The sonde collects the data with a single user-

replaceable sensor, plus an integral temperature sensor and pressure transducer. Each sensor measures its parameter via a variety

of electrochemical, optical, or physical detection methods. The 1-port bulkhead accepts any ProDSS sensor and automatically

recognizes its type. Depending upon user-deﬁned settings, the ProSwap Logger will collect data and store it onboard the sonde,

transfer the data to a data collection platform (DCP), or relay data to the ProSwap/ProDSS Handheld or a PC using Kor Software.

See Section 6 for information speciﬁc to vented level sondes.

Users communicate with the ProSwap Logger via the ProSwap or ProDSS Handhelds or via Kor Software with a USB communications

adapter to a PC.

Speciﬁcations

Material Titanium

Internal Logging

Memory Capacity 512 MB, > 100,000 data sets

Sample Rate Up to 1 Hz

Software Kor Software

Communications

Sonde

Adapters

YSIP, SDI-12

USB, Flying Lead

Power

External

Powering

Charging

Internal1

5.4-16 V

9-16 V

Rechargeable Li-Ion battery

Temperature

Operating

Storage

-5 to 50°C

-20 to +80°C

Depth Rating Up to 100 m

Battery Life1≥ 90 days2

Dimensions3

Diameter

Length

w/ Battery

w/o Battery

Weight

w/ Battery

w/o Battery

2.65 cm,1.045 in

57.35 cm, 22.57 in

49.70 cm, 19.57 in

0.57 kg, 1.26 lb

0.45 kg, 0.99 lb

Warranty 2 years

¹ Internal battery only available on select models.

² Battery life based on CT sensor at 15 min logging; this will vary depending

on the type of sensor and logging frequency.

3 Sonde only; does not account for integral cable. Total weight will depend

on cable length.

57.34 cm

39.43 cm

17.91 cm

O 2.65 cm

O 2.54 cm

Sensor

Probe Guard

Cable Connector

Vent Tube

Cable

Depth Sensor

Thermistor

Battery Compartment

Sensor Port

ProSwap Logger

1.2 ProSwap Logger Contents

Inspect the outside of the shipping container(s) for damage. If you see any damage, contact the shipping carrier immediately.

Carefully remove the equipment from the shipping box and verify that all contents are present.

Contents:

• ProSwap Logger with Integrated Cable

• Probe Guard

• Weight (for Probe Guard)

• Storage Sleeve

• Sponge

• Graduated Cylinder

• USB Drive (contains Kor Software)

• Cable Connector Cap

• Cable Grip Kit

• Cable Management Kit (4m, 10m, 20m) or Cable Spool (30m+)

• Maintenance Kit

• Desiccant Kit (Vented units ONLY)

If any parts or materials are damaged, contact YSI Customer Service at 800-897-4151 (+1 937 767-7241) or the authorized YSI

distributor from whom the instrument was purchased.

Introduction

1.3 ProSwap Logger Power Supply

There are two different versions of the ProSwap Logger – one with an internal, rechargeable lithium ion battery

and one without.

Internal Battery Version

Models:

• 610150-XX

• 610151-XX

• 610152-XX

This version includes a built-in, rechargeable lithium ion battery. This battery, fully charged, will last at least 90 days at a 15 minute

log interval no matter which ProDSS Sensor is installed and may last longer depending on the sensor type.

Full recharge time may take up to 14 hours depending on the power source.

This battery can be recharged by connecting the cable to a handheld meter (ProSwap or ProDSS). The ProSwap Logger will drain

the battery of the handheld to charge its own battery. Plug the handheld’s USB connector into the AC power adapter or a computer

USB connector to maintain charging.

Alternatively, the battery can be charged using the USB adapter accessory (sold separately). Plug the USB cable into the AC power

adapter or a computer USB connector to enable charging.

Non-Battery Version

Models:

• 610153-XX

• 610154-XX

• 610155-XX

This version features no onboard power and therefore requires an external power supply. Options for external power include the

following:

• ProSwap or ProDSS Handheld – The handheld will power the logger as long as it is connected and powered on.

• ProSwap Logger AA Power Pack – The power pack utilizes six AA batteries to provide power to the logger for at least 90 days at

a 15 minute logging interval.

• USB Adapter – The USB Adapter will power the logger when connected to a PC USB port or AC adapter.

• Flying Lead Adapter – The ﬂying lead adapter may be used to supply external power (9-16 V) and provide communication with

a data logger.

Section 2

Setup

This section will cover the setup and operation of the ProSwap Logger using a ProDIGITAL

Handheld (ProSwap and ProDSS). To prepare the sonde for operation, you will need to:

• Install sensor on the bulkhead or plug the port

• Connect ProSwap Logger to a handheld or PC via USB Adapter (not included)

2.1 ProDSS Sensor Installation

and Removal

The ProSwap Logger includes built-in temperature and depth sensors in addition to a single port. The port will allow any ProDSS

smart sensor to be connected.

NOTICE: The sensor connector and bulkhead port are not wet-mateable. Make sure that the sensor connector and

bulkhead port are clean and dry before sensor installation.

1 Sensor port

2 O-ring

3 Sensor retaining nut

4 Sensor

5 1-port cable assembly

6 Thermistor

7 O-ring lubricant

8 Port plug

Setup

Inhaltsverzeichnis

Andere Xylem Datenlogger Handbücher

Xylem

Xylem ebro EBI 25 Bedienungsanleitung

Xylem

Xylem ebro EBI 10 Series Bedienungsanleitung

Xylem

Xylem Ebro EBI 16 Bedienungsanleitung

Xylem

Xylem MJK Chatter E-MAIL Bedienungsanleitung

Xylem

Xylem YSI Storm 3 Bedienungsanleitung

Xylem

Xylem ebro EBI 11 Bedienungsanleitung

Xylem

Xylem ebro EBI 25-System Bedienungsanleitung

Xylem

Xylem YSI Pro Swap Logger Bedienungsanleitung

Xylem

Xylem ebro EBI 300 Gebrauchs- und Pflegehandbuch

Xylem

Xylem ebro EBI 300 Bedienungsanleitung

Xylem

Xylem ebro EBI 40 Bedienungsanleitung

Xylem

Xylem Ebro EBI 100 Series Bedienungsanleitung

Xylem

Xylem ebro EBI 12 EX Series Bedienungsanleitung

Xylem

Xylem MJK Chatter Bedienungsanleitung

Xylem

Xylem ebro EBI 20 Series Bedienungsanleitung

Xylem

Xylem ebro EBI 300 Bedienungsanleitung

Xylem

Xylem ebro EBI 310 Bedienungsanleitung

Xylem

Xylem McDonnell & Miller GUARD DOG 750-MT-120 Bedienungsanleitung

Xylem

Xylem ebro EBI 300 Bedienungsanleitung

Xylem

Xylem YSI Storm3 Bedienungsanleitung

Xylem

Xylem ebro EBI IF Series Bedienungsanleitung

Beliebte Datenlogger Handbücher anderer Marken

TESTO

TESTO 176 Bedienungsanleitung

HBM

HBM SOMAT XR CX22B-R Bedienungsanleitung

Agtrix

Agtrix 380i Bedienungsanleitung

Hobo

Hobo H8 Pro Bedienungsanleitung

Beijing ART Tech

Beijing ART Tech PCI2320 Bedienungsanleitung

Athena

Athena GET SL1 Bedienungsanleitung

Motec Systems

Motec Systems C185 Bedienungsanleitung

Beijing ART Tech

Beijing ART Tech USB2832 Bedienungsanleitung

HT Italia

HT Italia XL421 Bedienungsanleitung

Rotronic

Rotronic HygroLog HL20 Bedienungsanleitung

MRC

MRC DW-6092 Bedienungsanleitung

Racelogic

Racelogic VBOX LapTimer Bedienungsanleitung

Edu-Logger

Edu-Logger 900-240 Bedienungsanleitung

Elma

Elma DT173 Bedienungsanleitung

MadgeTech

MadgeTech PRTemp140 Technisches Datenblatt

Comet

Comet U0121M Bedienungsanleitung

pico Technology

pico Technology PT-104 Bedienungsanleitung

Soil Instruments

Soil Instruments GTecLink Bedienungsanleitung