Xylem Rule 25S-6W Bedienungsanleitung

Fully Automatic

Bilge Pump

INSTRUCTION MANUAL

Manuel d’utilisation de pompe de cale entièrement

automatique

Bedienungsanleitung für die vollautomatische

bilgenpumpe

Manuale delle istruzioni per la pompa di sentina

completamente automatica

Manual de instrucciones de la bomba de achique

totalmente automática

Handledning för helt automatisk länspump

Handleiding volautomatische lenspomp

Purpose of this manual

The purpose of this manual is to provide necessary information for product installation, operation

and maintenance.

CAUTION: Read this manual carefully before installing, using or servicing this

product. Failure to follow the instructions within this manual could result in explosion,

property damage, severe personal injury and/or death.

DANGER: Failure to follow this instruction manual may lead to signicant property

damage or may result in serious injury or death.

About safety messages

It is extremely important that you read,understand and follow the safety messages and regulations

carefully before handling the product.They are published to help prevent these hazards:

WARNING:

• The operator must be aware of safety precautions to prevent physical injury.

• Operating, installing or maintaining the unit in any way that is not covered

in this manual could cause death, serious personal injury or damage to the

equipment. This includes any modication to the equipment or use of parts

not provided by Xylem.If there is a question regarding the intended use of

equipment, please contactXylem representative before proceeding.

• Do not change the service application without the approval of a authorized

Xylem representative.

• Personal accidents and health problems

• Damage to the product

• Product malfunction

NOTICE: Save this manual for future reference, and keep it readily available at the

location of the unit.

Safety

Safety terminology and symbols

Hazard Level:

DANGER

WARNING

CAUTION

NOTICE

Indication:

Ahazardous situation which,if not avoided,will result indeath orserious injury.

Ahazardous situation which,if not avoided,could result indeath orserious injury.

Ahazardoussituationwhich,if notavoided,could resultinminor ormoderateinjury.

Apotential situation which,if not avoided,could result in undesirable conditions.

Apractice notrelatedto personal injury.

ELECTRICAL HAZARD:

Hazard categories can either fall under hazard levels or let specic symbols replace the ordinary

hazard levels symbols. Electrical hazards are indicated by the following specic symbols:

These are examples of other categories that can occur.They fall under the ordinary hazard

levels and may use complementing symbols:

Hazard categories

• Crush hazard

• Cutting hazard

• Arc ash hazard

General safety rules

These are safety rules apply:

• Always keep work area clean

• Pay attention to the risks presented by gas and vapors in the work area.

• Avoid all electrical dangers. Pay attention to the risks of electric shock or arc ash hazards

• Always bear in mind the risk of drowning, electrical accidents and burn injuries

User safety

Safety equipment

Usesafety equipment according tothecompany regulations.Use this safetyequipmentwithin the work area:

Electrical connections

Electrical connections must be made by certied electricians in compliance with all

international, national,state and local regulations. For more information about requirements,

see sections dealing specically with electrical connections.

• Hard hat

• Safety goggles, preferably with side shields

• Protective shoes

• Protective gloves

• Gas mask

• Hearing protection

• First-aid kit

• Safety devices

NOTICE: Never operate a unit unless safety devices are installed.

Precautions before work

Observe these safety precautions before you work with the product or are in connection with the product:

• Provide a suitable barrier around the work area, for example, a guard rail

• Make sure that all safety guards are in place and secure

• Make sure that you have a clear path of retreat

• Make sure that the product cannot roll or fall over and injure people or damage property

The work area

Always keep the station clean

Waste and emissions regulations

Observethese safety regulations regardingwaste and emissions:

Wash the skin and eyes

Followthese proceduresfor chemicals or hazardousfluids that have comeintocontact with your eyesorskin:

• Make sure that the lifting equipment is in good condition

• Use a lifting harness,a safety line and a breathing device as required

• Allow all system and pump components to cool before you handle them

• Make sure that the product has been thoroughly cleaned

• Disconnect and lock out power before you service the pump

• Check the explosion risk before you weld or use electric hand tools

• Appropriately dispose of all waste

• Handle and dispose of the processed liquid in compliance with applicable

environmental regulations

• Clean up all spills in accordance with safety and environmental procedures

• Report all environmental emissions to the appropriate authorities

Environmental safety

Electrical installation

For electrical installation recycling requirements, consult your local electric utility

Recycling guidelines

Always follow local laws and regulations regarding recycling

WARNING: Radiation Hazard.Do NOT send the product to Xylem if it has been

exposed to any nuclear radiation

Condition

Chemicals or

hazardous uids

in eyes

Chemicals or

hazardous uids

on skin

Action

1. Hold your eyelids apart forcibly with your ngers

2. Rinse the eyes with eyewash or running water for al least 15 minutes

3. Seek medical attention

1. Remove contaminated clothing

2.Wash the skin with soap and water for a least 1 minute

3. Seek medical attention, if necessary

DANGER: This product is not intended for damage control or to deal with ooding result-

ing from hull damage.This product is intended to be used in Bilge Pumping Systems for small

craft with a hull length up to 24 meters,as described within the introduction and scope of ISO

15083. Bilge Pumping Systems, as specied in ISO 15083, are limited to normal amounts of

water in an intact boat due to spray, rain,seepage, spillage, and occasional small amounts of

water shipped from boat movements in heavy weather. Use of product in any other way could

result in ooding, catastrophic damage to craft, serious personal injury, or death.

WARNING: This pump is designed for use with fresh water and salt water ONLY. Use with

any other hazardous, caustic,or corrosive material could result in damage to the pump and

the surrounding environment,possible exposure to hazardous substances and injury.

WARNING: Check the function of all bilge pumps at regular intervals. Clear pump

inlets from debris. If seacocks are tted in the fore and aft peak bulkheads, they shall be

kept closed and shall only be opened to let water drain into the main bilges.

How Fully Automatic

Bilge Pumps Work:

Rule Automatic bilge pumps eliminate the

need for a separate oat switch to activate

the pump. Once power is supplied, starting

and stopping is completely automatic. The

pump checks for water every 2 ½ minutes (20

seconds for model 25S-6WC) by turning on

for a second and measuring load against the

impeller.If water is present, the pump remains

on until the water is removed. Thereafter the

pump resumes its 2 ½ minute check cycle.The

automatic pumps feature two positive leads:

an automatic (brown) and a manual override

(brown with a white stripe).

2.5 min

0.5 sec

2.5 min

0.5 sec

2.5 min

0.5 sec

.75"

(2cm)

OFF

1.5"

(3.8cm)

OFF

STOP

ARRÊT

STOPP

ALTO

+12"

(+30cm)

CAUTION: Disconnect power from the

system before working on the unit to avoid

personal injury,damage to the surrounding

environment and/or damage to the unit.

CAUTION:

Always install proper fuse size to

prevent damage to product should a short occur.

Failure to install proper fuse could increase risk

of pump malfunction potentially resulting in

personal injury and/or re hazard.

CAUTION: Keep all wire connections

above the highest water level.Wires must be

joined with butt connectors and a marine grade

sealant to prevent wire corrosion.

WARNING: Electrical connections

should be performed by a competent marine

electrical technician.

–

+–

Note: Output is based on 10 hour break-in period and at 13.6V (12V models) or 27.2V (24V

models). On 12 volt pump: Minimum voltage of 10.5 volts required. On 24 volt pump: Minimum

voltage of 21 volts required. [For data on table 1.1]

Note: Les données proviennent d’une période de rodage de 10heures et d’essais

à 13,6V (modèles 12V) ou 27,2V (modèles 24V). Pour pompe 12 volts: Tension

minimum requis de 10,5 volts. Pour pompe 24 volts: Tension minimum requis de 21

volts. [Pour les données sur le tableau 1.1]

Hinweis: Die Pumpleistung richtet sich nach der zehnstündigen Einlaufzeit und

danach, ob 13,6V (12V-Modelle) oder 27,2V (24V-Modelle) anliegen. Für 12-Volt-

Pumpe: Mindest erforderliche spannung 10,5 Volt. Für 24-Volt-Pumpe: Mindest

erforderliche spannung 21 Volt. [Für Daten auf Tabelle 1.1]

Nota bene: l’uscita è basata su un periodo di rodaggio di 10 ore a 13,6V (modelli

a 12V) o 27.2V (modelli a 24V). Pump 12 volt: minima tensione ha richiesto 10.5 volt.

Pump 24 volt: minima tensione ha richiesto 21 volt.[Per i dati sulla tabella 1.1]

Opmerking: De uitvoer is gebaseerd op een inloopperiode van 10 uur en bij 13,6

V (12 V-modellen) of 27,2 V (24 V-modellen). Voor 12 volt pomp: 10.5 volt minimaal

vereiste spanning Voor 24 volt pomp: 21 volt minimaal vereiste spanning.

[Voor gegevens over tabel 1.1]

Obs: Uteffekt baseras på en 10 timmar lång inkörsperiod med 13.6V(12V-modeller)

eller 27.2V (24V-modeller). För 12 volts pump: Minsta spänning krävs 10,5 volt.För 24

volts pump: Minsta spänning krävs 21 volt. [För uppgifter om tabell 1.1]

Nota: La salida se basa en un período de reposo de 10 horas y a 13.6V (modelos

de 12V) ó 27.2V (modelos de 24V). Para la bomba de 12 voltios: Voltaje mínimo

requerido de 10,5 voltios. Para la bomba de 24 voltios: Voltaje mínimo requerido

de 21 voltios. [Para los datos de la tabla 1.1]

Rated Flow Open Flow

Output @ 0ft/0m

(0 kPa) GPH (LPH)

Open Flow

Output @ 3.35ft/1m

(10 kPa) GPH (LPH)

Open Flow

Output @ 6.7ft/2m

(20 kPa) GPH (LPH)

Débit nominal

Débit libre

Sortie à 0 pied/0m

(0 kPa) GPH (LPH)

Débit libre

Sortie à 3,35 pieds/1m

(10 kPa) GPH (LPH)

Débit libre

Sortie à 6,7 pieds/2m

(20 kPa) GPH (LPH)

Gemessener

Durchuss

Offener Durchuss

Pumpleistung bei 0m

(0kPa) GPH (LPH)

Offener Durchuss

Pumpleistung bei 1m

(10kPa) GPH (LPH)

Offener Durchuss

Pumpleistung bei 2m

(20kPa) GPH (LPH)

Flusso

nominale

Flusso aperto

Uscita @ 0ft/0m

(0 kPa) GPH (LPH)

Flusso aperto

Uscita @ 3,35ft/1m

(10 kPa) GPH (LPH)

Flusso aperto

Uscita @ 6,7ft/2m

(20 kPa) GPH (LPH)

Nominaal

debiet

Open debiet

Uitvoer @ 0ft/0m

(0 kPa) GPH (LPH)

Open debiet

Uitvoer @ 3,35ft/1m

(10 kPa) GPH (LPH)

Open debiet

Uitvoer @ 6,7ft/2m

(20 kPa) GPH (LPH)

Nominellt öde

Öppet öde

Effekt @ 0ft/0m

(0 kPa) GPH (LPH)

Öppet öde

Effekt @ 102,11cm/1m

(10 kPa) GPH (LPH)

Öppet öde

Effekt @ 204,22cm/2m

(20 kPa) GPH (LPH)

Caudal Nominal

CaudalAbierto

Salida @ 0 pies/0 m

(0 kPa) GPH (LPH)

Caudal Abierto

Salida @ 3.35 pies/1 m

(10 kPa) GPH (LPH)

Caudal Abierto

Salida @ 6.7 pies/2 m

(20 kPa) GPH (LPH)

500 500 (1892) 360 (1362) 260 (984)

800 800 (3028) 615 (2328) 425 (1608)

1100 1100 (4164) 860 (3255) 550 (2081)

1500 1500 (5678) 1200 (4542) 680 (2574)

2000 2000 (7570) 1620 (6132) 1300 (4921)

3700 3700 (14006) 2900 (10977) 2450 (9274)

4000 4000 (15142) 3527 (13351) 2952 (11174)

Table 1.1 / tableau 1.1 / tabelle 1.1 / tabella 1.1 / tabel 1.1 / tabell 1.1 / tabla 1.1

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Xylem Wasserpumpe Handbücher

Xylem

Xylem McDonnell & Miller MM-706B Bedienungsanleitung

Xylem

Xylem e-IXP Handbuch

Xylem

Xylem JABSCO 777 Series Bedienungsanleitung

Xylem

Xylem GOULDS e-HM Series Bedienungsanleitung

Xylem

Xylem LOWARA TP1 Bedienungsanleitung

Xylem

Xylem Lowara Presfix Beta MK2 Handbuch

Xylem

Xylem e-MP Bedienungsanleitung

Xylem

Xylem LOWARA e-SHE Series Bedienungsanleitung

Xylem

Xylem FLOJET M50 Bedienungsanleitung

Xylem

Xylem FLOJET 2840 Series Bedienungs- und Montageanleitung

Xylem

Xylem Goulds 3642 Bedienungsanleitung

Xylem

Xylem Aquavar IPC Bedienungsanleitung

Xylem

Xylem Flygt 2830.180 Bedienungsanleitung

Xylem

Xylem FLYGT Compit 901 Series Bedienungsanleitung

Xylem

Xylem Flygt Concertor 6020 Bedienungsanleitung

Xylem

Xylem FLOJET R3426-500 Bedienungsanleitung

Xylem

Xylem Goulds AquaBoost VS Bedienungsanleitung

Xylem

Xylem FLYGT Flygt 2071 Bedienungsanleitung

Xylem

Xylem G&L A-C 9100 Series Bedienungsanleitung

Xylem

Xylem Lowara e-SVI Series Handbuch

Xylem

Xylem Rule LoPro LP900S Bedienungsanleitung

Xylem

Xylem AC Fire Pump 8100 Series Bedienungsanleitung

Xylem

Xylem Bell & Gossett e-1510 Series Bedienungsanleitung

Xylem

Xylem JABSCO 50890 Bedienungsanleitung

Beliebte Wasserpumpe Handbücher anderer Marken

Neptun

Neptun NPHW 5500 Bedienungsanleitung

Sensidyne

Sensidyne Gilian BDX-II Montage- und Bedienungsanleitung

Draper

Draper 47808 Bedienungsanleitung

Trolla

Trolla 12820 Bedienungsanleitung

Sunfab

Sunfab SVH Series Bedienungsanleitung

WilTec

WilTec 50740 Bedienungsanleitung

Fieldmann

Fieldmann FVC 5015 EK Bedienungsanleitung

Everbilt

Everbilt EFSUB5-122HD Bedienungsanleitung

Graco

Graco Husky 3300e Bedienungsanleitung

esotec

esotec 101018 Bedienungsanleitung

Becker

Becker BASIC VASF 2.80/1-0.AC230 Bedienungsanleitung

Sykes AmeriPumps

Sykes AmeriPumps GP100M Fehlerbehebungshandbuch

DUROMAX

DUROMAX XP WX Series Bedienungsanleitung

BRINKMANN PUMPS

BRINKMANN PUMPS SBF550 Bedienungsanleitung

Franklin Electric

Franklin Electric IPS Bedienungsanleitung

Milton Roy

Milton Roy PRIMEROYAL Bedienungsanleitung

STA-RITE

STA-RITE ST33APP Bedienungsanleitung

GÜDE

GÜDE HWW 900 GC Bedienungsanleitung