Yaesu ZCUT-10 Bedienungsanleitung

INSTRUCTION MANUAL

Contents

Thank you very much for purchasing our tape dispenser ZCUT-10.

Most of the function is the same as ZCUT-9GR, but the function to

fold the tape edge is added.

This is most effective feature to remove a tape very easily in prod-

uction process required or end customers removing a tape.

Please read this instruction manual carefully in order to use this

machine properly.

After that, please keep this manual in your file and read it again as

need arises.

Please read before use

P5-6

P10

P11

P12

P12-13

P14

P15

Read Before Use

Safety Instructions

Definition of Warning and Caution Symbols

Warning

Identification of Parts

Load the Tape

Set the Tape Length

Mode Setting

Programing Function

Folding Mode

How to Manage a Curling Tape

Use Narrow Tape / Use Two Rolls in a Same Time

Other Functions

Replace the Blade Unit

Maintenance

When tape jammed is happened

Error Messages

Trouble Shooting

Specifications

Warranty

Indicates a potentially hazardous situation which if not

avoided, could result in death or serious injury.

Indicate that miss-handing may result in danger and

that the operator is at risk of injury, or the machine is

at risk of damage.

Indicates Caution

A symbol within the triangle, or the description, will indicate

a specific hazard.

A Prohibited Action

Asymbol within the circle, or the description, will indicate

prohibited action.

A Required Action

Asymbol within the circle, or the description, will indicate

the required action.

Definition of Warning and Caution Symbols

Warning

Caution

The safety guidelines in this Instruction Manual must be observed in

order to prevent damage tothe machine or injury tothe operator or

other persons.

The safety guidelines presciribed "Warning " and "Caution" describe

possible injury or damage that may be suffered from operating or

maintaining the machine in a manner other than as described in this

Instruction Manual.

Read and follow the safety precautions carefully before reading the

Instruction Manual.

Safety Instructions

Warning

Do not plug in, unplug the cord, or operate the machine with wet

hands.

Failure to observe this may result in injury due to electric shock.

Never insert your finger, or any other body part, or any foreign

object into the machine.

Failure to observe this may result in injury.

Keep hair or loose clothing away from the machine while it is

operating.

Failure to observe this may result in injury.

This machine is intended for industrial use only.

Do not allow untrained operators or children to operate the machine.

Failure to observe this may result in injury.

Turn off the power switch and unplug the machine prior to replacing

the blade unit or peforming any maintenance on the machine.

Failure to observe this may result in serious injury.

Do not use this machine for anything other than its specified

applications.

Use of the machine for any unintended applications can cause injury

to the operator or failure of the machine.

SENSOR

BLADE UNIT

FLEXIBLE TAPE SUPPORT TAPE HOLDER ADJUST LEVER

CONTROL PANEL

Identification OfParts

UPPER CASE

AUTO / MANUAL MODE

BUTTON

LED (Blue LED)

LED(Green LED)

REV BUTTON

START BUTTON

FWD BUTTON

SELECT BUTTON

＋BUTTON

－BUTTON

DISPLAY

CONTROL PANEL

HOLD DOWN ROLLER UNIT

ROLLER LOCK LEVER

TAPE OUTLET

BLADE UNIT

RELEASE LEVER

BOTTOM OF BODY

SEPARATOR

BLADE OILASSISTSTAND

GUIDE PLATE

FUSE HOLDER

FUSE

SPARE FUSE

POWERSWITCH

LOWER TAPE HOLDER

TAPE FEED ROLLER

TAPE INLET

HOLD DOWN

ROLLER REL-

EASE BUTTON

TAPE HOLDER

AC CORD INLET

Identification OfParts

◆Plug in the AC CORD to the AC CORD INLET.

◆Make sure the POWERSWITCH is off then plug into an appropriate

　grounded AC outlet.

◆Turn the POWER SWITCH on.

When the POWER SWITCH is turned on, a buzzer will has a sound.

At this moment, the mode is set to MANUAL.

◆Press the HOLD DOWN ROLLER RELEASE BUTTON.

◆Place a roll of tape in the machine.

◆Hold the tape by adjusting the TAPE HOLDERS.

Adjust the TAPE HOLDERS to a proper width, slide the TAPE HOLDER

ADJUST LEVER from the front to the rear of the machin then close it.

The TAPE HOLDERS should hold the roll lightly in the center of the cavity

of the machine.

This is very important because it keeps the tape in the center.

The tape passes over the SENSOR in front of the BLADE UNIT.

To support a larger roll of tape, pull the LOWER HOLDER out.

◆Put the tape on the TAPE FEED ROLLER.

◆Press the FWDBUTTON until the tape comes out from the TAPE OUTLET.

When using a strong sticky adhesive tape, pull a little bit tape out in

positioning into the TAPE INLET.

Press the FWDBUTTON continuously for a few seconds, also help the

tape in positioning in the TAPE INLET.

◆After the tape is loaded and the TAPE HOLDERS are adjusted, close the

HOLD DOWN ROLLER UNIT.

◆Press the START BUTTON.

Remove the first piece of tape and discard it.

Always use Tweezers to remove tape.

Whenever set the tape, make sure that

adhesive side of tape is always faced down.

◆When you take the roll of tape out from the machine, pull the tape

　backward and pressing REV BUTTON.

Load the Tape

POWER SWITCH

OUTLET

AC CORD

INLET

remove the tape

◆Make sure that Blue LED is off.

When the LED LAMP is flashing or turned on, press AUTO/MANUAL

MODE and turn off the LED LAMP.

◆Press the START BUTTON once, the machine will feed-in a piece of tape

then cut it out based on your set length.

◆To cut another piece, press START BUTTON again.

◆Make sure that the Blue LED is flashing.

When the LED LAMP's lights are off, press AUTO/MANUAL BUTTON

and let the LED LAMP to flash.

◆Press the START BUTTON once, the machine will feed-in a piece of tape

then cut it out based on your set length.

When that piece of tape is removed, the machine will feed-in another

piece then cut it out.

The machine will feed-in and cut a new piece of tape once the piece of

tape is remomved.

AUTO MODE

MANUAL MODE

◆Make sure that DISPLAY indicating <cutting length>.

The cutting length is always indicates in some alphabets like A,b,C,d,E,F.

◆Set the cutting length.

Set your needed length by using +/- BUTTON.

The cutting length is adjustable in between 5 mm to 999 mm.

Can set six different length by using SELECT BUTTON.

If you press +/-BUTTON in a short while, the length in changed to 1 mm.

And if you press +/- BUTTON longer, if shows fast foraward.

Caution

The actual length is differ from the displayed length depends on the type

of the tape and its condition.

When cutting short length of tape, the length may not cut consistently

or tape is jammed.

Try several test cuts to insure proper operation.

If pressing －BUTTON for setting from b to F, you will be able to set ZERO.

However, machine will not start while alarming even though pressing

START BUTTON.

Mode Setting

Set the Tape Length

START

START CUT and STAND BY

CUT and STAND BY

REMOVE THE TAPE

TAPE FEED

FLASHING

LIGHTON

INDICATE CUTTING LENGTH

SET THE CUTTING LENGTH

INCREASE NUMBER

DECREASE NUMBER

SET AUTO / MANUAL

SELECT

＋

－

A～F

AUTO

MANU

LIGHTOFF

BLUE LEDLAMP

MANUAL MODE

AUTO MODE

順送りカット機能

SELECT

START

Green LED

Programing Function

Folding Mode

Function that cuts the material registered from A to F accordingly.

As refer to the following figure, operation will keep working.

This function may apply every mode.

◆Please follow the instruction on page 7.

◆Set the cutting length from A to F as you prefer.

◆Please set the cutting length in ZERO for between B to F if not necessary.

Then skip the position registered with ZERO accordingly and operate

repeatedly.

◆Apply the cutting length to your first cutting.

◆Press AUTO/MANUAL BUTTON more than 1 second.

Then [ . ] will appear on the lower right of Alphabet.

◆Press AUTO/MANUAL button and select AUTO MODE or MANUAL MODE.

◆Press START BUTTON and tape is ready to take.

When setting MANUAL MODE, the next cutting length will be desplayed.

When setting AUTO MODE, the next cutting tape is ready to take with

displaying the cutting length.

◆When discontinuing Program Function, please press AUTO/MANUAL

BUTTON longer and make sure that [ . ] is eliminated.

Operating Example

in the case of 6 different cut length setting

in the case of zero setting for E. F.

A～u：A 100mm

Set a cutting length

Programing Function setting

Press more

than 1 second

Press more

than 1 second

Buzzer sound

Setting

example

AUTO/MANUAL setting

MANUAL MODE

AUTO MODE

Confirm [ . ] description

Display the first cutting length

This mode is to fold the tape edge.

This mode can be used with other function.

◆Press SELECT BUTTON more than 1 second.

Green LED will be flashing if pressing SELECT BUTTON more than 1

second. If setting is completed and press START BUTTON, a piece of

tape with folding the edge as set the cutting length will be ready to take

after pressing START BUTTON again.

◆Set other mode as depends on your requirement.

◆In the case of folding mode, minimum cutting length is 15mm.

The folding length is fixed by 7mm.

◆When cancelling folding mode, please press SELECT BUTTON more

than 1 second. Please make sure that green LED is off.

Green LED Flassing

Feed a tape without

folding the edge

Feed a tape with

folding the edge

How to Manage a Curling Tape

Use Narrow Tape / Use Two Rolls in a Same Time

Other Functions

◆Press the HOLD DOWN ROLLER RELEASE BUTTON in order to open

the HOLD DOWN ROLLER UNIT.

◆Extend the ROLLER LOCK LEVER so that the roller will not turn.

◆Close the HOLD DOWN ROLLER UNIT.

With the rollers locked, the tension may cause the length to vary.

Cut several test pieces in order to adjust the length if needed..

If the tape is lesser than 25 mm width or you want to dispense two rolls in a

same time, use the SEPARATOR.

Cut lesser than 10 mm width of tape, put the GUIDE PLATE on the SEPA-

RATOR.

◆Remove the SEPARATOR from the bottom of body.

◆Open the HOLD DOWN ROLLER UNIT.

◆Insert the SEPARATOR into the body by slotting in tothe bottom of the cavity.

◆When you cut the tape lesser than 10 mm, put the GUIDE PLATE onto the

Separator.

◆Place one roll of the tape or either side by inserting a SEPARATOR for

loading tape.

◆To hold the tape by adjusting TAPE HOLDERS, it is unnecessary to push

the SEPARATOR out of position.

When dispensing two roll of tapes in a same time, it is a must tofeed-in

both of its' length in a same time.

◆Remove the first piece of tape.

◆When the second piece of the tape is removed, both side of tapes are also

dispensed.

FLEXIBLE TAPE SUPPORT

When you cut the tape longer or cut

non-adhesive tape / film, use FLEX-

IBLE TAPE SUPPORT in order to

avoid the tape fall down.

ASSIST STAND

Based on the tape material

or workpiece purpose, use

the ASSISTSTAND in order

to let the body of machine

towards a lower level.

SEPARATOR

GUIDE PLATE

Inhaltsverzeichnis

Andere Yaesu Büroausstattung Handbücher

Yaesu

Yaesu ZCUT-9 Bedienungsanleitung

Beliebte Büroausstattung Handbücher anderer Marken

silen

silen Space 2 Bedienungsanleitung

Middle Atlantic Products

Middle Atlantic Products LD Series Bedienungsanleitung

SHFL

SHFL DECK MATE BLACKJACK Bedienungsanleitung

DROMEAS

DROMEAS LINE Bedienungsanleitung

Siemens

Siemens HIPATH 2000 Bedienungsanleitung

VITRA

VITRA Stefan Hürlemann Dancing Wall Bedienungsanleitung

BISLEY

BISLEY Glide V2 Bedienungsanleitung

fully

fully Haven Bedienungsanleitung

Plus

Plus NF-20 Bedienungsanleitung

OCEE DESIGN

OCEE DESIGN SASS-0100 Bedienungsanleitung

NanaWall

NanaWall CSW75 Bedienungsanleitung

Vivo

Vivo DESK V000C Bedienungsanleitung

ABB

ABB 2TKA002145G1 Bedienungsanleitung

PolyVision

PolyVision Flow Bedienungsanleitung

MBM

MBM FC-10 Bedienungsanleitung

Wiremold

Wiremold V2400 Series Bedienungsanleitung

Vivo

Vivo PP-3-T072D Bedienungsanleitung

BuzziSpace

BuzziSpace BuzziNest Booth Bedienungsanleitung