Yaesu FTH-2006 Betriebsanleitung

Andere Handbücher für FTH-2006

1

Inhaltsverzeichnis

Andere Yaesu Transceiver Handbücher

Yaesu

Yaesu FT DX 3000 Bedienungsanleitung

Yaesu

Yaesu FTM-3100E Bedienungsanleitung

Yaesu

Yaesu VX-8DR Bedienungsanleitung

Yaesu

Yaesu FT-991 CAT Produkthandbuch

Yaesu

Yaesu FT-60R Bedienungsanleitung

Yaesu

Yaesu FTM-100DR Bedienungsanleitung

Yaesu

Yaesu FTDX5000 CAT BOOK Service-Handbuch

Yaesu

Yaesu FT-767GX Bedienungsanleitung

Yaesu

Yaesu FTDX101D Bedienungsanleitung

Yaesu

Yaesu FT-817 - Bedienungsanleitung

Yaesu

Yaesu FT-250R Bedienungsanleitung

Yaesu

Yaesu FT5Dr Bedienungsanleitung

Yaesu

Yaesu Mark-V FT-1000MP Bedienungsanleitung

Yaesu

Yaesu FT-100 Micro Mobile Handbuch

Yaesu

Yaesu FT-470 Bedienungsanleitung

Yaesu

Yaesu CPU-2500R Bedienungsanleitung

Yaesu

Yaesu FT-8100R Bedienungsanleitung

Yaesu

Yaesu MARK-V FT-100MP Bedienungsanleitung

Yaesu

Yaesu FT-736R Bedienungsanleitung

Yaesu

Yaesu FTM-3200DE Bedienungsanleitung

Yaesu

Yaesu FT-1802M Bedienungsanleitung

Yaesu

Yaesu FTA-750 Spirit Bedienungsanleitung

Yaesu

Yaesu FT-221 Series Handbuch

Yaesu

Yaesu Mark-V FT-1000MP Bedienungsanleitung

Beliebte Transceiver Handbücher anderer Marken

Kenwood

Kenwood ProTalk TK-3201 Bedienungsanleitung

Texas Instruments

Texas Instruments TLK10232 Bedienungsanleitung

Mizuho

Mizuho MX-2 Produkthandbuch

Kenwood

Kenwood TK-3180 Bedienungs- und Wartungshandbuch

Blitz

Blitz MJ-398U Bedienungsanleitung

Utilicom

Utilicom LongRanger 2050 Bedienungsanleitung

Standart

Standart HX290UKA Bedienungsanleitung

Altronix

Altronix Pace1PTM Bedienungsanleitung

Kirisun

Kirisun PT2208 Bedienungsanleitung

ELECRAFT

ELECRAFT KX2 Bedienungsanleitung

Zodiac

Zodiac K3 Bedienungsanleitung

Assa Abloy

Assa Abloy SecureComm HKC GSM-WIFI U Bedienungsanleitung

Kenwood

Kenwood TK-2217 Bedienungsanleitung

Siemens

Siemens PSO 4000 Bedienungsanleitung

Kenwood

Kenwood TS-590SG Bedienungsanleitung

Midland

Midland G8E-BT Handbuch

ComNav

ComNav Mariner X2 Bedienungsanleitung

Uniden

Uniden UH820 Series Bedienungsanleitung

PROGRAMMING YAESU FTH-2006

Programming this rig needs only a small screwdriver and some skill, no computer or

interface cords are needed.

Normally this rig display only a channel number "CH 0" to "CH 9" if all memories

where programmed.

You can't modify the frequency with the 4 keyboard's keys. But there are some (4)

hidden keys somewhere to achieve this.

A) Right of the display, remove the keyboard plastic cover with a small screwdriver or

a knife (it's glued) and you will see 4 additional keys on the keyboard just under the

originals.

B) Those keys are like this:

1) Power on the rig

2) Change display from channel to frequency by pressing once the "hidden"

"Channel/Frequency" key.

3) Adjust to the desired frequency using the big upper right knob or "Scan +" or

"Scan –" keys (You can obtain a 1 MHz step depressing the "Function" key

before turning the knob or "Scan +" or "Scan –" keys.

4) From the frequency display, press the "Function" key (a small F is displayed)

and quickly press the "Channel/Frequency" key, a small blinking memory

number will appear in the upper left corner of the display, change the memory

number using the big upper right knob or "Scan +" or "Scan –" keys and press

again the "Channel/Frequency" key to store the memory.

5) Back to "channel display" mode using the "Channel/Frequency" key, the

desired frequency is stored in the chosen memory.

To use a "shift" (repeater operation), press the "Channel/Frequency" key and power

on the rig, the display shows .000, rotate the big upper right knob to change to the

desired value, then the "Function" key (small F in display) and the "Priority" key to

display a +or -

CTCSS

Under the "Light" key there is the key for the CTCSS

First press will enable CTCSS at transmit ("enc" displayed).

Second press of the key will enable CTCSS at receive ("dec" displayed)

Third press of the key will disable both.

Pressing the "Function" key and then the "CTCSS" key you can adjust the CTCSS

frequency.

In fact, programming this rig is exactly like the well-known FT-23R except for some

functions

Some other adjustments are inside the box (solder pads) (Do it at your own risks!)

Default setup is:

Solder pads

1 open

2 shorted

3 open

4 shorted

5 shorted

6 open

7 open

8 open

9 open

10 shorted

Frequency step is solder pad #4: open = 5 KHz step, shorted = 12.5 KHz step.

(May needs replacing some components)

Battery saver is solder pad #6: open = on, shorted = off

Channel / frequency display is solder pad #7: open = channel, shorted = frequency

Busy channel lock out is solder pad #8: open = off, shorted = on

Busy tone lock out is solder pad #9: open = off, shorted = on

Behind PTT rubber cover you will find a switch for testing/clone mode

That's all

Enjoy

F6BXM