Yale 7110 Bedienungsanleitung

7110(F) and 7170 (F) (LBR)

Surface Vertical Rod Exit Device Series

Installation Instructions

without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.

For technical support contact Yale®at 800.438.1951 x5033 or [email protected]

8094700010000 05/21

This product can expose you to

lead which is known to the state

of California to cause cancer and

birth defects or other reproductive

harm. For more information go to

www.P65warnings.ca.gov.

WARNING

whole or in part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.

For technical support contact Yale®at 800.438.1951 x5033 or [email protected]

Surface Vertical Rod Exit Device Series

Installation Instructions

7110(F) and 7170(F) (LBR)

8094700010000 05/21

TOC Table of Contents

1 Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

2 Handing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

3 Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

4 Pre-Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

5 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

a Mark Door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

b Prepare Door, Frame & Sill . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

c Size Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

d Mount Device & Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

e Rod Preparation and Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

f Bottom Bolt Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

g Complete Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

6 Plastic Installation Template 7000 exit devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

7 7110 Template 791 Strike . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

8 7170 Template 790 Strike. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

9 7170 Template 726 Strike. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

Abbreviation Fastener Description

PPH”AB”SMS Phillips Pan Head Type “AB” Sheet Metal Screw

PFHUMS Phillips Flat Head Under Cut Machine Screw

PFHMS Phillips Flat Head Machine Screw

PRH”AB”SMS Phillips Round Head Type “AB” Sheet Metal Screw

PTH”AB”SMS Phillips Truss Head Type “AB” Sheet Metal Screw

PPHMS Phillips Pan Head Machine Screw

PFH”AB”SMS Phillips Flat Head Type “AB” Sheet Metal Screw

PRHMS Phillips Round Head Metal Screw

All dimensions are in inches (mm)

unless otherwise noted.

whole or in part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited

For technical support contact Yale®at 800.438.1951 x5033 or [email protected]

8094700010000 05/21

Surface Vertical Rod Exit Device Series

Installation Instructions

7110(F) and 7170(F) (LBR)

1Package Contents

(2) 1/4-20 X 1" PPHMS

(Metal Door)

(2) #14 x 1-1/2" PPH”AB”SMS

(Wood Door) Cover

(3) 10-24 x 1/4" (6mm) PPHMS

Top Latch

(Panic & Fire Label)

Bottom Bolt Case

Panic & Fire Label

Top Rod

(2) 1/4-20 X 3/4" PFHMS

(Metal Door)

(2) #14 x 1-1/2" PFH”AB”SMS

(Wood Door)

Bottom Rod Assembly

Deadbolt

790 Strike Bolt Case Cover

(2) 8-32 x 1/4" (6mm) PFHMS

Bottom Mounting Plate

(2) #8 x 1/2" (13mm) PRH”AB”SMS

Guide Cover

(2) #6 x 3/8" (10mm) PTH”AB”SMS

Rod Guide

Roll Pin

Latch Cover

791 Strike

Strike Plate

Shim (2) Supplied

(3) 10-24 x 3/4" (19mm) PFHMS

Top Mounting Plate

Hole Plug

(Fire Label

Devices)

(2) 8-32 x 5/16" (8mm) PFHUMS

Rod Guide

Guide Cover

(3) 10-24 x 1/4" (6mm)

PPHMS

(2) 8-32 x 1/4" (6mm) PFHMS

(2) #6 x 3/8" (10mm)

PTH”AB”SMS

Top Rod Connector

(2) #8 x 1/2" (13mm) PRH”AB”SMS

(2) 1/4-20 X 3/4" PFHMS

(Metal Door)

(2) #14 x 1-1/2" PFH”AB”SMS

(Wood Door)

‘

Dogging Key

(3) 8-32 x 5/16"

PFHUMS

(2) 1/4-20 X 1" PPHMS

(Metal Door)

(2) #14 x 1-1/2" PPH”AB”SMS

(Wood Door)

End Clamp

End Cap

Top brac ket and 726 strike

required f or 7170(F)(LBR).

Strike Angle Must

Engage Str ike 726

Top Strike

12-24

PRHMS

Dogging

Feature to hold bots

retracted and touchpad

depressed, for push-pull

door operation.

To Dog Device:

1. Insert dogging key.

2. Hold touchbar

depressed.

3. Turn ky 1/4 turn

clockwise

(Not a feature of fire labeled

devices.)

Retaining Clip

Popper

Cap

Plug

Popper Assembly required

for 7170(F) with Less

Bottom Rod (LBR) Option.

Refer to separate instruction

sheet 60-7110-0002-999.

whole or in part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.

For technical support contact Yale®at 800.438.1951 x5033 or [email protected]

Surface Vertical Rod Exit Device Series

Installation Instructions

7110(F) and 7170(F) (LBR)

8094700010000 05/21

2 Handing

Unreinforced Doors or Frames

Doors and Frames with walls having a structural thickness (metal skin plus reinforcement or solid

hardwood) to engage less than (3) full screw threads are considered unreinforced.

Unreinforced Doors: Use SNB (sex nuts and bolts).

Unreinforced Frames: Use Blind Rivet Nuts.

Recommended fasteners for unreinforced openings are not necessarily supplied by Yale Locks and

Hardware.

To change hands remove (4) screws

and vertical lifter assembly.

Rotate device to oppsite hand (180

degrees).

Insert lifter assembly under lift block

and re-install screws.

(4) 8-32 x 3/16" PPHMS(4) 8-32 x 3/16" PPHMS

LHR DoorRHR Door

LHR DeviceRHR Device

Lift Block

Vertical Lifter AssemblyVertical Lifter Assembly

3 Maintenance

1. Periodically remove covers and coat mechanisms with a silicone base lubricant. This is particularly

required in corrosive environments for proper product function.

2. Check mounting fasteners periodically. Retighten if found loose. Apply screw locking compound

(available at automotive part stores) or change part fasteners if screws continue to back out.

3. Periodic checks (and adjustments) of strikes are required to compensate for changes in the

opening (e.g. door sagging).

4 Pre-Installation

Reinforcement

Door Skin Blind Rivet Nut

Door Must Swing F reely

Min. Door Stile

4-1/2" (114mm)

Door and frame must

meet structural and

dimensional specifications

on exit device template(s)

for door and frame

preparation.

whole or in part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited

For technical support contact Yale®at 800.438.1951 x5033 or [email protected]

8094700010000 05/21

Surface Vertical Rod Exit Device Series

Installation Instructions

7110(F) and 7170(F) (LBR)

5 Installation

Single Door or Pair without Mullion

Locate and mark horizontal and vertical reference centerlines as shown.

LHR door shown, preparation is typical for both door hands.

aMark Door

bPrepare Door, Frame, & Sill

FINISHED

FLOOR

or THRESHOLD

LHR DOOR

INSIDE FACE

VERTICAL

REFERENCE

HORIZONTAL

REFERENCE

39-15/16

(1014)

Note:

Door should be in the closed position while marking horizontal and vertical reference lines. Paper or

the plastic template may be used in this step

Top Latch & 791 or 726

Strike Template

Device Template

Floor Strike Template

FINISHED FLOOR or THRESHOLD

Bottom Case

Template

LHR DOOR

INSIDE F

ACE

VERTICAL

REFERENCE

HORIZONTAL

REFERENCE

Rods & Strikes

1. Locate “Device Template” aligning VERTICAL

REFERENCE and HORIZONTAL REFERENCE lines. Tape

template to door face.

2. Extend centerline of rod and strikes from “Device

Template” to door top and bottom, on door face.

3. Locate top latch/strike and bottom bolt case templates in

place over centerline of Rods and Strikes on door. Tape

templates in place and mark holes.

Note:

The centerline of the rods and strikes used to install top and

bottom bolts is not the Vertical Reference centerline.

4. Locate and tape Trim Template to door when required (See instructions packed with trim).

5. Mark and prepare holes per installation template (exclude 791 or 726 strike, holes prepared in

Step 7).

6. Locate top latch/strike and bottom bolt case templates in place over centerline of Rods and

Strikes on door. Tape templates in place and mark holes.

7. Locate 790 Bottom Strike Template. Tape in place over Rods and Strikes centerline

on door. Tape template in place and mark hole locations. Holes to be prepared in Step 7.

8. Remove templates from door.

whole or in part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.

For technical support contact Yale®at 800.438.1951 x5033 or [email protected]

Surface Vertical Rod Exit Device Series

Installation Instructions

7110(F) and 7170(F) (LBR)

8094700010000 05/21

5Installation, continued

cSize Device

Device must be field cut to size, as required

HINGE SIDE OF DOOR

STILE

* LHR Door (Door Open)

inside face

STOP

SURFACE

CUT

LINE

2-1/4

(57)

1-3/8

(35)

Min.

Horizontal line

Dogging

Hole

3/8

(10)

Min.

Determine device length

1. Close door. Measure 2-1/4” (57mm) from the stop surface on the hinge side of the door.Mark

horizontal reference at this point.

Note:

This dimension must be 3/8” (10mm) minimum from edge of the stile on the door.

2. Open door. Align mounting holes in device with mounting holes in the door. Mark device where it

crosses the mark from Step 1. If mark is less than 1-3/8” (35mm) min. from dogginghole, a shorter

device is required.

3. Before cutting, make sure the end cover is in place and there is no gap between it and the pushpad.

Cut device on mark from Step 2.

whole or in part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited

For technical support contact Yale®at 800.438.1951 x5033 or [email protected]

8094700010000 05/21

Surface Vertical Rod Exit Device Series

Installation Instructions

7110(F) and 7170(F) (LBR)

5Installation, continued

dMount Device & Components

1. Mount trim when required per

installation instruction sheet

provided with trim pack.

2. Fasten device at the latch head

using (2) 1/4-20 x 1” (25mm)

PPHMS or 3/8” (10mm) diameter

SNB (Metal Door) or #14 x 1-1/2”

PPH “AB” SMS (Wood Door), to

door surface.

3. Set device level. Using the end

clamp as a template, locate

the end clamp mounting holes

and mount end clamp using (2)

1/4-20x1” (25mm) PPHMS or

3/8” (10mm)SNB or #14 x 1-1/2”

PPH“AB”SMS (Wood Door).

4. Attach top and bottom mounting

plates to the door surface using

(4) 1/4-20 x 3/4” (13mm)

PFHMS or 3/8” (10mm) diameter

SNB or #14 x 1-1/2” (38mm)

PPH“AB”SMS (Wood Door).

Attach top latchand bottom

bolt case to the top and bottom

mounting plates using (6) 10-24 x

1/4” (6mm) PFHMS.

Note:

For 7170(F) (LBR) options see 726

strike template.

5. Check slide action. Press on the

pushpad. The slide should move

up freely. If not, verify handing.

See Section 2. Release the

touchbar. The slide should fall

back to the original rest position.

End

Clamp

Rod Guid e

To p

Mounting

Plate

790 Strike

To p

Latch

LDevice Mounting Holes,

Rods, & Strikes

Rod Guide

(2) 1/4-20 x 3/4" (19mm)

PFHMS

(3) 10-24 x 1/4" (6mm)

PPHMS

791 Str ike

Bottom

Mounting

Plate

Bottom Bolt

Case

(2) 1/4-20 x 3/4" (19mm)

PFHMS

(3) 10-24 x 1-1/4" (32mm)

PPHMS

Bottom Bolt

Case

Device

6-3/8

(

416)

(381)

1/2

(13)

Note: 726 Strike and top

bracket not shown.

6. Install rod guides.

a. Locate the rod guide as dimensioned. Spot (2) mounting holes.

b. Prepare holes

- Metal door: #28 - .140” (3.5mm) diameter Inside Face.

- Wood door: #28 - .140” (3.5mm) diameter x 3/4” (19mm) deep

c. Mount guides. Fasten with (2) #8 x 1/2” (13mm) PRH”AB”SMS as shown above.

whole or in part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.

For technical support contact Yale®at 800.438.1951 x5033 or [email protected]

Surface Vertical Rod Exit Device Series

Installation Instructions

7110(F) and 7170(F) (LBR)

8094700010000 05/21

5Installation, continued

eRod Preparation & Assembly

Note: Below listed instructions are based on a device mounted 3915/16" (1014mm) from finished floor or thresh-

old. Any deviation on device mounting height must be accommodated to insure proper device function.

60-1510-0280: 2" (51mm)

60-1510-0277: 6" (152mm)

60-1510-0278: 12" (305mm)

(Specify Device Finish)

A. Top Rod Sizing

1. For openings under 7' (2134mm), subtract the actual opening height from 7'

(2134mm).

Example: 6'8" (2032mm) opening

7'0" (2134mm) - 6'8" (2032mm)

= 4" (102mm)

Top Rod must have 4" (102mm) cut from end with 1/8” (3mm) thru hole. Use at-

tached drill fixture to locate and re-drill 1/8" (3mm) dia. hole thru the top rod. Make

sure rod bottoms out inside drill fixture prior to drilling. (See Figure 5A).

B. Assemble Top Rod

Insert Top Rod Connector into sized Top Rod and Install 1/8” (3mm) x 1/2”

(13mm) Roll Pin thru both pieces until flush on both sides. (See Figure 5B).

Top Rod

Flat Face

(2 Sides)

Top Rod

Connector

Flush

1/8" (3mm)

x 1/2" (13mm)

36-1/8

(918)

Bottom Rod

Assembly

Bolt

1/2

(13)

7/8

-1/4

12)

Adjustable

(Ref.)

1/8

(3)

Drill Fixture

3/8

(10)

Figure 5A: Drill Pin Hole

Figure 5B: Top Rod Assembly

2. For opening over 7' (2134mm), subtract 7' (2134mm) from the actual opening height.

Example: 7'6" (2286mm) - 7'0" (2134mm)

= 6" (152mm).

Top Rod must have a 6" (152mm) extension added to length (See below for available rod lengths).

fBottom Bolt Assembly

A. Thread Bottom Bolt into Bottom Rod Assembly.

B. Leave 1/2” (13mm) for adjustment.

whole or in part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited

For technical support contact Yale®at 800.438.1951 x5033 or [email protected]

8094700010000 05/21

Surface Vertical Rod Exit Device Series

Installation Instructions

7110(F) and 7170(F) (LBR)

(Press in place)

Bolt

Engagement

Frame

Stop

Rod Guide

3/8"

(10)

Cover

Screw

Hole

Cover

Screw

Hole

Cover

Screw

Hole

Cover

Screw

Hole

Rod Guide

Slide

Roller

Bolt

Tripping

Lever

gComplete Installation

Shim

(2) Supplied (Start With One)

Strike Plate

(Ridges Face Down)

791 Strike

(3) 10-24 x 3/4" (19mm) PFHMS

Top Strike Detail

A. Install Top Rod and 791 Strike

1. Thread Top Rod Assembly onto Top Latch. Lift rod to fully retract Top

Latchbolt. Depress Pushpad and hold depressed. Adjust top rod length

until Rod Connector seats into the Slide Assembly in latch case.

Note: For 7170 devices, skip section (2a) and 2(b). See the installation

instructions for the 726 strike on page 9.

2a. Position the Top Strike Roller between the Tripping Lever and the Bolt on

the Top Latch. Verify hole positions and prepare holes per Installation

Instruction Template.

2b. Install Top Strike and Strike Plate using (2) #1024 x 3/4” (19mm) PFHMS

thru outer slots. Adjust and shim strike as needed for zero door rattle. Add

third screw (#1024 x 3/4” (19mm) PFHMS) after final adjustments.

3. If Top Bolt does not remain retracted when door is opened, Top Rod is too

short. Pull rod out of the guide and the slide then rotate rod to increase

length. Upper Bolt should retract flat.

4. If upper latch will not deadlock, Top rod is too long. Pull rod out of the

guide and the slide and rotate to decrease length.

* If 7170 LBR, skip section B.

B. Install Lower Rod and 790 Strike

1. With door open, actuate Pushpad to retract upper latch. Hang Lower rod

from bottom of Slide and adjust bolt so that it clears the finished floor by

1/4”.

2. Verify location of pipe strike template. Prepare the strike hole and install

the pipe strike. Set in place with appropriate bonding material.

3. With the door open, actuate pushpadt o retract upper latch. Adjust bolt

height by pulling the rod out of the guide and slide and rotating until the

bolt clears the pipe strike by 1/8”.

C. Test device action by Touchbar, by Trim, by Dogging.

D. Install covers.

Note: Bottom Bolt will retract to

1/8” (3mm) above Floor Strike.

Floor covering in the door path

must be laid out accordingly.

whole or in part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.

For technical support contact Yale®at 800.438.1951 x5033 or [email protected]

Surface Vertical Rod Exit Device Series

Installation Instructions

7110(F) and 7170(F) (LBR)

8094700010000 05/21

Notes:

1. For 7170 series devices omit the 791 strike and use this template with the 726 strike template (page 15).

2. Mark L rods line on door face. Note that the centerline of the rods and strikes, used to install top and bottom

bolts, is not the vertical reference centerline.

3. For LBR devices, omit bottom latch and strike installation steps and see separate instructions for top latch

and strike.

4. Unreinforced frames require that #1024 blind rivet nuts (by others) be used to bolt strike. Frames are

considered not reinforced when strike mounting screws cannot engage (3) full threads.

5. Dimensions are given in inches (mm).

6. CAUTION: Office copiers and facsimile machines may change the size of a drawing and make the template

inaccurate to use as a door marker.

6Plastic Installation Template 7000 Exit Devices

77110 Template 791 Strike

Frame

Door Stop

Door

Template

All 7000 Exit De vices

7120(F),7160(F)

& 7220M(F) CVR

757F

Strike

Locatio n

Mortise

7130(F)

7150(F)(WS),7170(F)(WS)

Against Door Stop

or Mullio n

(when applicab le)

Vertical Reference

Wide Stile

Tr im Onl y

Against Door Surface

Wide Stile

Trim Onl y

Horizontal

Reference

Wide Stile

Tr im Onl y

Vertical Reference

Narrow Stile

Tr im Onl y

7120(F),7160(F)

& 7220M(F) CVR

For use in conjunction with

instruction sheets packed

with exit device.

Holes and slots are identified

below by exit device series

and trim. Prep door and

frame for only those features

required for the exit device

being installed.

Andere Handbücher für 7110

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Yale Türschloss Handbücher

Yale

Yale 680F Bedienungsanleitung

Yale

Yale YDM3109A Bedienungsanleitung

Yale

Yale YDR2105 Bedienungsanleitung

Yale

Yale Assure Lock 2 Plus Bedienungsanleitung

Yale

Yale GATEMAN YDM 3109 Bedienungsanleitung

Yale

Yale YDM4109 Bedienungsanleitung

Yale

Yale Doorman Bedienungsanleitung

Yale

Yale 2310BC Series Bedienungsanleitung

Yale

Yale YDR3110 Bedienungsanleitung

Yale

Yale Lockmaster AutoEngage Leitfaden

Yale

Yale Real Living YRD210-ZB Technische Daten

Yale

Yale Nest x Yale Installationsanleitung

Yale

Yale nexTouch Technische Daten

Yale

Yale Real Living YRL210 Technische Daten

Yale

Yale Assure Lock YRC256 Technische Daten

Yale

Yale Code Handle Handbuch

Yale

Yale nexTouch Technische Daten

Yale

Yale 630F Bedienungsanleitung

Yale

Yale YDD120 Bedienungsanleitung

Yale

Yale YDG313 Bedienungsanleitung

Yale

Yale GATEMAN YDM 3109 Bedienungsanleitung

Yale

Yale YRD210 Technische Daten

Yale

Yale D100 Series Bedienungsanleitung

Yale

Yale SCP400 Series Bedienungsanleitung

Beliebte Türschloss Handbücher anderer Marken

Assa Abloy

Assa Abloy effeff 827A-IP Bedienungsanleitung

Iseo

Iseo MA1A Bedienungsanleitung

ID Lock

ID Lock 150 Bedienungsanleitung

Lockly

Lockly ACCESS TOUCH PRO Bedienungsanleitung

iLoq

iLoq G50S Bedienungsanleitung

SDC

SDC Z7835 Bedienungsanleitung

ilco

ilco 452 Bedienungsanleitung

Samsung

Samsung shs-h705 Bedienungsanleitung

TRU-BOLT

TRU-BOLT 08102017 Bedienungsanleitung

CDVI

CDVI 500-LADJ Bedienungsanleitung

Igloohome

Igloohome Deadbolt 2S Metal Grey Montage- und Wartungsanleitung

eSSL

eSSL FL-300 Bedienungsanleitung

Dorma

Dorma MUNDUS PREMIUM GK 50 Benutzerhandbuch

SCOOP

SCOOP Pullbloc 4.1 FS Panik Bedienungsanleitung

Siegenia

Siegenia KFV AS3500 Bedienungsanleitung

Saflok

Saflok Quantum ädesē RFID Bedienungsanleitung

ArrowVision

ArrowVision Shepherd 210 Bedienungsanleitung

Assa Abloy

Assa Abloy Sargent 10X Line Bedienungsanleitung