Assa Abloy Sargent 10X Line Bedienungsanleitung

A8334 07/22

Installation Instructions

For installation assistance contact SARGENT

1-800-543-3658 • techsupport.sargent@assaabloy.com • www.sargentlock.com

Reproductioninwholeorinpart without the express written permission of ASSAABLOYAccess

andEgressHardwareGroup,Inc.isprohibited.

11 3

13 15

Installation Instructions

2Product Components

1Tools Required

10XLinewithBHWTrim

Fig. Description

1 Inside escutcheon & lever assembly

2 Outside escutcheon & lever

assembly

3 Inside spring housing assembly

4 Screws - through-bolt (2) #10-32

x 1-1/4"

5 Lockbody assembly with mounting

plate

6 Outside spring housing assembly

7 Cylinder spacer

8 Cylinder

9 Key

10 Latch

11 Screws - latch (2) #8-32 x 3/4"

12 Screws - strike (2) #12-24 x 3/4"

13 Strike

14 Strike box (Optional)

15 Screws- through-bolt (3) #10-24 x

3-1/2"

3Door Preparation

IMPORTANT

• The accuracy of door preparation is critical for proper functioning and security of this lever handle lock. Misalignment can

cause premature wear and a lessening of security.

• Be sure to verify backset before marking and drilling door.

1. Use template A8335 to mark the door (Figure 1).

2. Drill the door according to the template.

3. Verify the dimensions (Figure 2).

4. Install the strike (Figure 3)

DOOR

FRAME

Desired

height

above

floor

Template

Backset must

match latch

Door bevel

2x 7/16" (11mm) hole

1-1/8"

(29mm)

2-1/4"

(57mm)

1" (25mm)

hole

5/32" (4mm)

2-3/4"

(70mm)

Strike Box

Attaching Screws

#12 -24 x 3/4"

3x 1/2" (13mm) hole

4-3/4"

(120mm)

1-11/16"

(43mm)

2-1/8"

(54mm)

hole

5/8"

(16mm)

• 5/32"drillbit • 1/2 "drillbit • 7/16"drillbit • 1/8"drillbit

• #2Phillipsscrewdriver • T25SecurityTorx ® screwdriver • T15SecurityTorx ® screwdriver

10XLinewithBHWTrim

InstallationInstructions

part without the express written permission of ASSAABLOY Access and Egress Hardware Group, Inc. is prohibited.

For installation assistance contact SARGENT

1-800-543-3658 • techsupport.sargent@assaabloy.com • www.sargentlock.com A8334 07/22

Centerline

ofretractor

Retractor

DimensionA

5Door Thickness Adjustment (if necessary)

6Install Outside Lockbody Assembly

To adjustlockto doorthicknessif otherthan 1-3/4"

(44mm)refer toSection5.

Insert lockbodyassembly into doorfromoutside

makingsure thatlockbodyhooks latchcase and

retractorengages bolttail(s). (Figure 7)

DONOTFORCE.(If lockbodydoes not engagelatch

easily,checkdoor preparationfor errors.)

Latch bolttailshould becentered indepthof

retractor.If itis not,refer to Section5 to properly

adjustthe lockfordoor thickness.

Lockis factory presetfor1-3/4"(44mm) doorsunlessspecified. Toadjust lockto

doorthickness ifotherthan 1-3/4"(44mm):

1. Removeoutside spring housingfrom lockbody assembly.

2. Rotate mounting plate to adjust for proper door thickness.

• For 2"thick door the inside face of the mounting plate should be

flush with the face of the bearing. (Figure 5)

• Verify correct position from the markings on the through-bolt

stud, or by measuring from inside surface of the mounting plate to

the centerline of the retractor. (Figure 6)

3. Reassemble outside

springhousing onto

lockbodyassembly.

Door Thickness Dimension A

1-3/4"(44 mm) 7/8" (22mm)

2"(50 mm) 1" (25mm)

4Latch Installation

Insert latchin door. (Besure bevel edgeof bolt facesstrike plate.)

Attach with(2) #8-32x 3/4"screwssupplied.

Strike

Important: Deadlockinglatch must stopon strike whendoor is closed.

Bearing

These

surfaces

flush

MountingPlate

Figure 6Figure 5

10XLinewithBHWTrim

InstallationInstructions

part without the express written permission of ASSAABLOY Access and Egress Hardware Group, Inc. is prohibited.

For installation assistance contact SARGENT

1-800-543-3658 • techsupport.sargent@assaabloy.com • www.sargentlock.com A8334 07/22

7Cylinder Installation

IMPORTANT

Before installing cylinders:

• Use a flat blade screwdriver to rotate cam until the driver points

are in a 6 and 12 o’clock position. (Figure 8A)

Cylinder spacer should be installed “snapped”on to the cylinder

before installing into the outside trim assembly.

1. Install cylinder into the lever. (Figure 8B)

• Removetemporary construction coreor plasticcore. Ifkeyed, use

ControlKey.Rotate15° andpull.

• Insert permanentcoreinto lever withcontrol key. Rotate15° and

removekey.

a StandardCylinder(Figure8)

b InterchangeableorRemovableCore(Figure9)

Key

BHW Trim

Cylinder

Cylinder Spacer

Figure 8B

New Core

Figure 9

Viewintolockfrom

endoftrim

12o’clockdrivepoint

6o’clockdrivepoint

Figure 8A

IMPORTANT

• Remove tailpiece from construction core and insert into new core. If using 7 pin cores,

insert the 7 pin tail piece that’s supplied with the lock, before installing the core into the

lock.

• For XC LFIC cores, snap-on retainer must be installed onto tailpiece. Tail and retainer

assembly will press fit onto back of core. XC LFIC

For installation assistance contact SARGENT

1-800-543-3658 • techsupport.sargent@assaabloy.com • www.sargentlock.com

Reproductioninwholeorinpart without the express written permission of ASSAABLOY Access

andEgressHardwareGroup,Inc.isprohibited.

WARNING

Thisproduct canexpose youto lead

whichis knownto thestate of California

tocause cancerand birth defects orother

reproductiveharm. Formore informationgo

towww.P65warnings.ca.gov.

10XLinewithBHWTrim

InstallationInstructions

A8334 07/22

Competitor’s

Cylinder

Cap Pin

End Cap

9Cylinder Options

1. Providedless cylinder.

2. Depresscap pinandunscrew endcap to removetailpiece from

competitor’scylinder.(Figure 11)

3. Insert newtailpiece inorientation shown.

4. Reassembleend capovernew tailpiece.

a LevertoAcceptSchlage®orYale®FixedCoreCylinder(30-orYC- Option)

8Install Inside and Outside Escutcheon & Lever Assemblies

1. Alignand insert inside springhousing onto theinstalled lockbody.

2. Install (2) #10-32x 1-1/4” screwsto tighten thespring housing tothe door.

3. Mountinside escutcheonand leverassembly over theinside spring housing.

4. Mountoutsideescutcheon andlever assemblyover theoutside springhousing.

5. Securethe assembliesusingthe (3)screws #10-24 x3-1/2"(Figure 10)

Screws (2) #10-32 x 1-1/4"

Screws (3) #10-24 x 3-1/2"

Figure 10

Figure 11

Andere Assa Abloy Türschloss Handbücher

Assa Abloy

Assa Abloy Sargent AD-PE8600 Bedienungsanleitung

Assa Abloy

Assa Abloy MSL sFlipLock check Bedienungsanleitung

Assa Abloy

Assa Abloy Sargent AL-PE80 Series Bedienungsanleitung

Assa Abloy

Assa Abloy effeff Security lock 309 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Sargent PR100 Bedienungsanleitung

Assa Abloy

Assa Abloy Sargent PE8300 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Sargent PE80 Series Bedienungsanleitung

Assa Abloy

Assa Abloy 81 C Series Bedienungsanleitung

Assa Abloy

Assa Abloy ABLOY EL574 Bedienungsanleitung

Assa Abloy

Assa Abloy Effeff 319 Series Bedienungsanleitung

Assa Abloy

Assa Abloy PADDE Series Bedienungsanleitung

Assa Abloy

Assa Abloy Yale 6100 Bedienungsanleitung

Assa Abloy

Assa Abloy ZI IKON eCLIQ N109 Bedienungsanleitung

Assa Abloy

Assa Abloy EMTEK LISCIO Fehlerbehebungshandbuch

Assa Abloy

Assa Abloy Corbin Russwin FE6600 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Yale AYRD110 Bedienungsanleitung

Assa Abloy

Assa Abloy Yale nexTouch Technische Daten

Assa Abloy

Assa Abloy Valencia Filip Bedienungsanleitung

Assa Abloy

Assa Abloy Yale Essential YDME 70 Bedienungsanleitung

Assa Abloy

Assa Abloy Harmony H1 Bedienungsanleitung

Assa Abloy

Assa Abloy OneSystem type A Leitfaden

Assa Abloy

Assa Abloy Yale Real Living Assure Lock YRD216-ZW3 Montageanleitung

Assa Abloy

Assa Abloy Yale YDLL/BLK Fehlerbehebungshandbuch

Assa Abloy

Assa Abloy Corbin Russwin MP9800 Series Bedienungsanleitung

Beliebte Türschloss Handbücher anderer Marken

Iseo

Iseo MA1A Bedienungsanleitung

ID Lock

ID Lock 150 Bedienungsanleitung

Lockly

Lockly ACCESS TOUCH PRO Bedienungsanleitung

iLoq

iLoq G50S Bedienungsanleitung

SDC

SDC Z7835 Bedienungsanleitung

ilco

ilco 452 Bedienungsanleitung

Samsung

Samsung shs-h705 Bedienungsanleitung

TRU-BOLT

TRU-BOLT 08102017 Bedienungsanleitung

CDVI

CDVI 500-LADJ Bedienungsanleitung

Igloohome

Igloohome Deadbolt 2S Metal Grey Montage- und Wartungsanleitung

eSSL

eSSL FL-300 Bedienungsanleitung

Dorma

Dorma MUNDUS PREMIUM GK 50 Benutzerhandbuch

SCOOP

SCOOP Pullbloc 4.1 FS Panik Bedienungsanleitung

Yale

Yale MORTISE 8800 SERIES Bedienungsanleitung

Siegenia

Siegenia KFV AS3500 Bedienungsanleitung

Saflok

Saflok Quantum ädesē RFID Bedienungsanleitung

ArrowVision

ArrowVision Shepherd 210 Bedienungsanleitung

Baldwin

Baldwin 009 Series Bedienungsanleitung