Yanmar RT70 Bedienungsanleitung

RT70
Yanmar® 4TNV98CT, equipped with tires or tracks
Operator’s
Manual
CMW® 053-3307
Issue 2.0
Original Instruction

RT70 Operator’s Manual Overview - 1
Overview
Chapter Contents
Serial Number Location . . . . . . . . . . . . . . . . . . . . . 2
Intended Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Equipment Modification . . . . . . . . . . . . . . . . . . . . 3
Machine Components . . . . . . . . . . . . . . . . . . . . . . 4
Regulatory Notices . . . . . . . . . . . . . . . . . . . . . . . . . . 5
• United States. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
• Canada . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Operator Orientation . . . . . . . . . . . . . . . . . . . . . . . 6
Operating Area . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
About This Manual . . . . . . . . . . . . . . . . . . . . . . . . . 7
• Bulleted Lists . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
• Numbered Lists . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
California Proposition 65
Diesel engine exhaust and some of its constituents are known to the State of California to
cause cancer, birth defects, and other reproductive harm. www.P65warnings.ca.gov.

Overview - 2 RT70 Operator’s Manual
Serial Number Location
Serial Number Location
Record serial numbers and date of purchase in spaces provided. Serial number is located as shown.
Item
Date of manufacture
Date of purchase
Machine serial number
Front attachment serial number
Rear attachment serial number
t63om001h21.epst63om001h21.eps

RT70 Operator’s Manual Overview - 3
Intended Use
Intended Use
The RT70 is a riding trencher designed to install buried service lines of various sizes using a variety of Ditch
Witch® attachments.
This machine is intended for operation only according to the instructions in this manual. Operate machine
in ambient temperatures from 10° to 115°F (-12° to 46°C). Contact your Ditch Witch dealer for provisions
required for operating in extreme temperatures. Use in any other way is considered contrary to the
intended use.
This machine should be used with genuine Ditch Witch chain, teeth, and sprockets. It should be operated,
serviced, and repaired only by professionals familiar with its particular characteristics and acquainted
with the relevant safety procedures.
Equipment Modification
This equipment was designed and built in accordance with applicable standards and regulations.
Modification of equipment could mean that it will no longer meet regulations and may not function
properly or in accordance with the operating instructions. Modification of equipment should only be
made by competent personnel possessing knowledge of applicable standards, regulations, equipment
design functionality/requirements and any required specialized training.
Attachment Max. width/diameter Max. depth
BH70 backhoe 18” (460mm) bucket 89” (2.3m)
CT70 trencher 12” (305mm) 61” (1.54m)
MT12 microtrencher 0.75-1.25” (19-32mm) 6-12.5” (165-318mm)
MT16 microtrencher 0.5-1.5” (12.7-38.1mm) 0-16” (0-406mm)
RC20 reel carrier 84” (2.1m) reel diameter n/a
ST70 trencher 12” (305mm) 63.8” (1.62m)
VP70 plow n/a 36” (915mm)
NOTICE: The protection offered by the Rollover Protective Structure (ROPS) will be impaired if it has
been subjected to any modification, structural damage, or has been involved in an overturn accident.
The ROPS must be replaced after a roll-over.

Overview - 4 RT70 Operator’s Manual
Machine Components
Machine Components
1. Rollover Protective Structure (ROPS)
2. Operator station
3. Center console
4. Engine compartment
5. Backfill blade*
*Optional
1122334455
t63om002h21.epst63om002h21.eps

RT70 Operator’s Manual Overview - 5
Regulatory Notices
Regulatory Notices
Your equipment is designed and tested to meet regulatory codes and standards for electromagnetic compatibility. Digital
electronics including wireless devices may be options on your equipment.
United States
Your equipment may contain the following: FCC ID: XPYLISAU200 or FCC ID: XMR201903EG25G
This device complies with Part 15 of the FCC Rules. Operation is subject to the following conditions: (1) this device may not cause
harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired
operation. Changes or modifications not expressly approved by The Charles Machine Works, Inc. could void the user’s authority
to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC
rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Canada
CAN ICES-2/NMB-2
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:
(1) this device may not cause interference, and (2) this device must accept any interference, including interference that may
cause undesired operation of the device.
Your equipment may contain the following IC: 8595A-LISAU200 or IC: 10224A-201903EG25G.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation
est autorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'appareil doit accepter tout
brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.
Votre équipement peut contenir les éléments suivants IC: 8595A-LISAU200 ou IC: 10224A-201903EG25G

Overview - 6 RT70 Operator’s Manual
Operator Orientation
Operator Orientation
1. Front
2. Right side
3. Rear
4. Left side
Operating Area
Operate only from designated seat(s).
IMPORTANT: Top view of machine is shown.
11
2244
33
t63om003h21.epst63om003h21.eps
t63om004h21.epst63om004h21.eps

RT70 Operator’s Manual Overview - 7
About This Manual
About This Manual
This manual contains information for the proper use of this machine. Cross references such as “See page
50” will direct you to detailed procedures.
Bulleted Lists
Bulleted lists provide helpful or important information or contain procedures that do not have to be
performed in a specific order.
Numbered Lists
Numbered lists contain illustration callouts or list steps that must be performed in order.

Overview - 8 RT70 Operator’s Manual
About This Manual

RT70 Operator’s Manual Foreword - 9
Foreword
This manual is an important part of your equipment. It provides safety information and operation
instructions to help maintain your Ditch Witch equipment.
Read this manual before using your equipment. Keep it with the equipment at all times for future
reference. If you sell your equipment, be sure to give this manual to the new owner.
If you need a replacement copy, contact your Ditch Witch dealer. If you need assistance in locating a
dealer, visit our website at www.ditchwitch.com or write to the following address:
The Charles Machine Works, Inc.
ATTN: Marketing Department
PO Box 66
Perry, OK 73077-0066
USA
The descriptions and specifications in this manual are subject to change without notice. The Charles
Machine Works, Inc. reserves the right to improve equipment. Some product improvements may have
taken place after this manual was published. For the latest information on Ditch Witch equipment, see
your Ditch Witch dealer.
Thank you for buying and using Ditch Witch equipment.
Inhaltsverzeichnis
Andere Yanmar Rasenmäher Handbücher
Beliebte Rasenmäher Handbücher anderer Marken

TALEN TOOLS
TALEN TOOLS AVR HGM30 Bedienungsanleitung

DEWEZE
DEWEZE ATM-725 Bedienungsanleitung

Weed Eater
Weed Eater 180083 Bedienungsanleitung

Husqvarna
Husqvarna Poulan Pro PP185A42 Bedienungsanleitung

Better Outdoor Products
Better Outdoor Products Quick Series Bedienungsanleitung

Cub Cadet
Cub Cadet 23HP Z-Force 60 Betriebsanleitung












