Yoshimura 070BG139600 Bedienungsanleitung

RESEARCH&DEVELOPMENT OF AMERICA, INC.

www.yoshimura-rd.com

FENDER ELIMINATOR KIT

070BG139600

Yamaha XSR900

5420 DANIELS STREET STE A, CHINO CA., 91710 · (800) 634-9166 · (909) 628-4722 · FAX (909) 591-2198

THIS PRODUCT IS NOT DOT APPROVED.

Yoshimura R&D of America, Inc. is not liable or responsible for any resulting event caused by the

installation of this product. Check with local laws and regulations for compliance prior to

installation and use. This product is not intended for use on public highways.

! !

No.

Item

Description

Qty.

13960-FEBKT

Fender Eliminator Bracket

070BG-LH-K1

LED License Plate Light

070BG-LPF

License Plate Frame

13960-TSB00-L

Left Turn Signal Bracket

13960-TSB00-R

Right Turn Signal Bracket

M6X16BHS

6mm x 16mm Button Head Screw

M6X14BHS

6mm x 14mm Button Head Screw

M6X10BHS

6mm x 14mm Button Head Screw

M4X6BHS

4mm x 6mm Button Head Screw

6MMWASHER

6mm Washer

6MMLN

6mm Nylon Lock Nut

BN-SSS-22-18

Butt Connectors

17029

Yoshimura Sticker Sheet

Optional Parts

072BGLTSFK

Yoshimura LED Front Turn Signal Kit

072BGLTSR

Yoshimura LED Rear Turn Signal Kit w/ Relay

070BGUNVTBKT

Universal Turn Signal Bracket Kit

** Not shown on diagram.

*** The Yoshimura Universal Turn Signal Bracket Kit is to be used with aftermarket stud-mounted turn signals and is sold separately.

Assembly Diagram

6. Using masking tape and marker, mark and

mask fender as shown. Cut and trim using a

rotary tool and file edges smooth removing any

burrs.

7. Cut the stock license plate light connector wires

on the stock fender assembly side. Be sure to

cut at least a 6” section of wire from the

connector.

8. Trim keyhole cover as shown. File edges

smooth.

1. Remove rider seat.

2. Remove the four bolts securing seat latch

bracket and set aside seat bracket to access

rear fender nuts.

3. Locate and disconnect brake/tail light, license

plate light, and rear turn signal connectors.

4. While securely supporting the stock fender

assembly, remove the four fender nuts and

carefully remove the stock fender assembly

making sure not to damage connectors.

5. Disassemble the stock fender assembly.

- Remove seat keyhole cover.

- Remove the brake/tail light assembly.

- Remove the upper fender cover.

- Remove left and right turn signals.

- Separate plastic fender from metal fender

support bracket base.

Removal

4. Install the stock turn signals onto (No. 4,5)

13960-TSB00-L/R, left and right turn signal

brackets using the stock hardware.

5. Re-install trimmed plastic fender onto metal

fender support bracket using the stock screws

and install assembled fender eliminator bracket

on top of plastic fender. Secure (No. 1)

13960-FEBKT, fender eliminator bracket using

(No. 8) M6X10BHS, 6mm screws from

underneath.

6. Re-install upper fender cover using opposite

steps of removal.

7. Re-install brake/tail light using opposite steps of

removal.

8. Install (No. 4,5) 13960-TSB00-L/R, left and right

turn signal brackets on the sides of the fender

support bracket using (No. 8) M6X10BHS, 6mm

screws.

9. Route wires through stock location and re-install

trimmed keyhole cover on the backside of the

fender assembly.

10. Re-install fender assembly using the four

fender nuts. Torque to factory specification.

11. Re-connect license plate light, brake/tail light,

and turn signal connectors.

12. Re-install seat latch bracket and rider seat.

13. Check for proper function of license plate light,

turn signals, brake light, and that all brackets

and components are secure prior to riding.

Installation

1. Install (No. 2) 070BG-LH-K1, license plate light

onto (No. 1) 13960-FEBKT, fender eliminator

bracket using (No. 9) M4X6BHS, 4mm button

head screws.

2. Using the BN-SSS-22-18, butt connectors

provided in the kit, connect the Yoshimura

license plate light wires to the stock license

plate light wires as follows:

Blue -to- Red Wire

Black Wire -to- Black Wire

a) Strip the stock fender light wire ends

1/4” - 1/2” and insert into BN-SSS-22-18,

butt connectors provided in the kit.

b) Center the spliced wire ends in the

middle and using a heatgun or lighter,

apply heat evenly on the outer edges of

the butt connector to shrink and hold

wires in place.

c) Making sure that the stripped ends are

centered, heat the center of the butt

connector evenly until the solder begins

to liquify.

d) Allow to cool completely and tug both

ends of the wires to verify that connection

is secured.

Scan for link to butt connector instruction video.

3. Secure (No. 3) 070BG-LPF, license plate frame

to (No. 1) 13960-FEBKT, fender eliminator

bracket using the hardware shown below.

Andere Yoshimura Motorradzubehör Handbücher

Yoshimura

Yoshimura RS-3 Bedienungsanleitung

Yoshimura

Yoshimura 19140NS720 Bedienungsanleitung

Yoshimura

Yoshimura 224500D320 Bedienungsanleitung

Yoshimura

Yoshimura Street 216600C250 Bedienungsanleitung

Yoshimura

Yoshimura 070BG141200 Bedienungsanleitung

Yoshimura

Yoshimura RACE SERIES Bedienungsanleitung

Yoshimura

Yoshimura 070BG133001 Bedienungsanleitung

Yoshimura

Yoshimura Street Series Bedienungsanleitung

Yoshimura

Yoshimura 070BG125511 Bedienungsanleitung

Yoshimura

Yoshimura 15002B0520 Bedienungsanleitung

Yoshimura

Yoshimura 070BG123100 Bedienungsanleitung

Yoshimura

Yoshimura 133200J220 Bedienungsanleitung

Yoshimura

Yoshimura Enduro Series Bedienungsanleitung

Yoshimura

Yoshimura 070BG131000 Bedienungsanleitung

Yoshimura

Yoshimura Enduro Series Bedienungsanleitung

Yoshimura

Yoshimura RS-12 Bedienungsanleitung

Yoshimura

Yoshimura 225850S321 Bedienungsanleitung

Yoshimura

Yoshimura 570-400-0300 Bedienungsanleitung

Yoshimura

Yoshimura Signature Series Bedienungsanleitung

Yoshimura

Yoshimura 070BG131001 Bedienungsanleitung

Yoshimura

Yoshimura RACE 11621C0520 Bedienungsanleitung

Yoshimura

Yoshimura RACE Series Bedienungsanleitung

Yoshimura

Yoshimura X-TREAD 559-592-V000 Bedienungsanleitung

Yoshimura

Yoshimura 19701BD520 Bedienungsanleitung

Beliebte Motorradzubehör Handbücher anderer Marken

SRC

SRC B-TRK502-01-01-SL Bedienungsanleitung

3M Speedglas 9100 MP Bedienungsanleitung

hepco & becker

hepco & becker 6307520 00 01 Bedienungsanleitung

HOMCOM

HOMCOM AA0-077 Bedienungsanleitung

hepco & becker

hepco & becker 6307558 00 01 Bedienungsanleitung

Wunderkind Custom

Wunderkind Custom 106503-F15 Benutzerhandbuch

Dräger

Dräger HPS 3500 Bedienungsanleitung

M-WAVE

M-WAVE SKI Bedienungsanleitung

Kuryakyn

Kuryakyn 6212 Bedienungsanleitung

hepco & becker

hepco & becker 6507504 00 01 Bedienungsanleitung

Tool it

Tool it PROMAX LCD 9.13G Bedienungsanleitung

Custom Dynamics

Custom Dynamics TruWrapz Bedienungsanleitung

Roof

Roof RO200 CARBON Bedienungsanleitung

Kabuto

Kabuto Japan IBUKI Bedienungsanleitung

PUIG

PUIG 5051 Bedienungsanleitung

rizoma

rizoma ZTH050 Bedienungsanleitung

Joubert

Joubert 10001711 Bedienungsanleitung

Sperian

Sperian Optrel p420 Bedienungsanleitung