Zanussi Electrolux FAE 1026 V Bedienungsanleitung

WASHING MACHINE

FAE 1026 V

INSTRUCTION BOOKLET

35.292.988/0

35.292.988…FAE1026V.qxd 30/06/2005 19:43 Página 1

Dear customer,

Please read these operating instructions carefully

and pay particular attention to the safety notes

indicated in the first pages. We recommend that you

keep this instruction booklet for future reference and

pass it on to any future owners.

Transport damages

When unpacking the appliance, check that it is not

damaged. If in doubt, do not use it and contact the

Service Centre.

The symbols you will see on some paragraphs of this booklet have the following meaning:

The warning triangle and/or the key words (Warning!, Caution!) emphasize information that is particularly

important for your safety or correct functioning of the appliance.

The information marked with this symbol provides additional instructions and practical tips on the use of

the appliance.

Tips and information about economical and ecological use of the machine are marked with this symbol.

Our contribution to the protection of the

environment: we use recycled paper.

35.292.988…FAE1026V.qxd 30/06/2005 19:43 Página 2

Maintenance 22-23

Bodywork 22

Detergent dispenser drawer 22

Cleaning of the drainage area 22

Water inlet filter 23

Emergency emptying out 23

Frost precautions 23

Something not working? 24-26

Warnings 4-5

Disposal 5

Tips for environmental protection 5

Technical specifications 6

Installation 7-8

Unpacking 7

Hydraulic connection 7

Levelling 8

Electrical connection 8

Your new washing machine 9

Description of the appliance 9

Detergent dispenser drawer 9

Use 10

Control panel 10

Controls 10-12

Washing hints 13

Sorting the laundry 13

Temperatures 13

Before loading the laundry 13

Maximum loads 13

Laundry weights 13

Removing stains 13

Detergents and additives 14

Quantity of detergent to be used 14

International wash code symbols 15

Operating sequence 16-18

Washing programmes 19-21

Contents

35.292.988…FAE1026V.qxd 30/06/2005 19:43 Página 3

Installation

• All internal packing must be removed before using

the appliance. Serious damage may be caused to

the machine or adjacent furniture if the protective

transit devices are not removed or are not

completely removed. Refer to the relevant

paragraph in the instruction book.

• Any electrical work required to install this appliance

must be carried out by a qualified electrician.

• Any plumbing work required to install this

appliance must be carried out by a qualified

plumber.

• After having installed the machine, check that it is

not standing on its electrical supply cable.

• If the appliance is placed on a carpeted floor,

ensure that air can circulate freely between the feet

and the floor.

• The power supply cable only can be replaced by a

person of the Technical Service.

Use

• This appliance is designed for domestic use. It

must not be used for purposes other than those for

which it was designed.

• Only wash fabrics which are designed to be

machine washed. Follow the instructions on each

garment label.

• Do not overload the appliance. Follow the

instructions in the instruction book.

• Make sure that all pockets are empty. Objects such

as coins, safety pins, pins and screws can cause

extensive damage.

• Do not machine wash garments saturated with

petroleum, methylated spirits, trichlorethylene, etc.

If such fluids have been used to remove stains

prior to washing, wait until they have completely

evaporated from the fabric before placing garments

in the appliance.

• Place small items such as socks, belts, etc. in a

cloth bag or pillowcase to prevent them getting

trapped between the drum and the tub.

• Use only the recommended quantities of fabric

softener. An excessive amount could damage the

laundry.

Warnings

• Leave the porthole door slightly ajar when the

appliance is not in use. This preserves the door

seal and prevents the formation of musty smells.

• Always check that water has emptied out before

opening the door. If not, drain the water following

the instructions in the instruction book.

• Always unplug the appliance and shut the water

tap after use.

General safety

• Repairs to the machine must be carried out only by

qualified personnel. Repairs carried out by

inexperienced persons could cause serious

danger. Contact your local Service Centre.

• Never pull the power supply cable to remove the

plug from the socket; always take hold of the plug

itself.

• During high temperature wash programmes the

door glass may get hot. Do not touch it!

The following warnings are provided in the interests of overall safety. You must read them carefully before

installing or using the appliance.

35.292.988…FAE1026V.qxd 30/06/2005 19:43 Página 4

Disposal

Tips for environmental protection

Packaging materials

The materials marked with the symbol are

recyclable.

>PE<=polyethylene

>PS<=polystyrene

>PP<=polypropylene

This means that they can be recycled by disposing of

them properly in appropriate collection containers.

Machine

The symbol on the product or on its packaging

indicates that this product may not be treated as

household waste. Instead it shall be handed over to

the applicable collection point for the recycling of

electrical and electronic equipment. By ensuring this

product is disposed of correctly, you will help prevent

potential negative consequences for the environment

and human health, which could otherwise be caused

by inappropriate waste handling of this product. For

more detailed information about recycling of this

product, please contact your local city office, your

household waste disposal service or the shop where

you purchased the product.

To save water, energy and to help protect the

environment, we recommend that you follow these

tips:

• Normally soiled laundry may be washed without

prewashing in order to save detergent, water and

time (the environment is protected too!).

• The machine works more economically if it is fully

loaded.

• With adequate pre-treatment, stains and limited

soiling can be removed; the laundry can then be

washed at a lower temperature.

• Measure out detergent according to the water

hardness, the degree of soiling and the quantity of

laundry being washed.

Child safety

• Children are often not aware of how dangerous

electrical appliances can be. When the machine is

working, children should be carefully supervised

and not be allowed to play with the appliance.

• The packaging components (e.g. plastic film,

polystyrene) can be dangerous to children - danger

of suffocation! Keep them out of children’s reach.

• Keep all detergents in a safe place out of children’s

reach.

• Make sure that children or pets do not climb into

the drum.

• When the appliance is to be scrapped, cut off the

electrical supply cable and destroy the plug with

the remaining cable. Disable the door catch in

order to prevent children from becoming trapped

inside while playing.

35.292.988…FAE1026V.qxd 30/06/2005 19:43 Página 5

DIMENSIONS Height 85 cm

Width 60 cm

Depth 60 cm

MAXIMUM RECOMMEND LOAD Cotton, linen 6 kg

Synthetics 2,5 kg

Delicates 2,5 kg

Woollens 2 kg

SPIN SPEED 1000 r.p.m. max.

POWER SUPPLY VOLTAGE/FREQUENCY 230 V/50 Hz

TOTAL POWER ABSORBED 2100 W

MINIMUM FUSE PROTECTION 10 A

WATER PRESSURE Minimum 50 kPa

Maximum 800 kPa

This appliance complies with the following EEC Directives:

73/23/EEC of 19/02/73 relating to low voltage

89/336/EEC of 03/05/89 relating to electromagnetic compatibility.

Technical specifications

It is dangerous to alter the specifications or attempt to modify this product in any way.

Care must be taken to ensure that the appliance does not stand on the electrical supply cable.

Any electrical work required to install this appliance should be carried out by a qualified electrician or

competent person.

Any plumbing work required to install this appliance should be carried out by a qualified plumber or

competent person.

The power supply cable only can be replaced by a person of our Service Force Centre.

Intallation instructions

35.292.988…FAE1026V.qxd 30/06/2005 19:43 Página 6

Installation

Transit security bars

Before starting the machine up, the transport

security bars must be removed as follows:

You are advised to keep all the transport security

bars in case the appliance has to be transported

again.

1. Unscrew and remove

the three rear screws

by means of a key.

2. Lean the appliance

back on the rear and

fit one of the

polystyrene angles

between the appliance

and the floor.

Make sure the hoses

are not squashed.

3. Carefully remove the

plastic bags on the left

and the right, pulling

them to the centre of

the appliance

4. Place the machine in an upright position and

remove the three plastic bolts.

5. Plug the 3 holes with the plastic plugs which you

can find in the envelope containing the instruction

booklet.

Hydraulic connection

There should be a COLD WATER tap near the

washing machine with a screwing on connection

pipe of 3/4 gas for the water supply, a sink, a wash

basin or a drainage system in the wall.

Previously check if:

— it is not a hot water tap.

— the running water is clean. If not, run off a

reasonable amount of water to flush out any

debris that may have collected in the pipes.

Have the permanent drainage system in the wall

checked by a plumber.

A) Carefully screw the

pipe to the tap taking

care not to damage the

screwdrive and fix the

nut well on to the end in

order to avoid leaking.

B) If necessary turn the

hose adequately by

unscrewing the nut at the

rear of the appliance.

C) Now tighten the nut

anew to avoid leaks.

(Open the tap and asure

that it does not leak and

close it again.)

D) Place the discharging

hose in a washbasin or

sink with the aid of the

bent piece delivered

separately. The bent

piece has to be entered

into the tube’s mouth in

order to assure the

support. Aforesaid piece

allows the hose to be

fixed to the wall by means

of an opening on the

upper part and that way

the hose does not move

and its falling is avoided.

P0287

P0018

AL009

P0001

P0002

P0021

P0022

P1088

35.292.988…FAE1026V.qxd 30/06/2005 19:43 Página 7

1,5 m. Max.

60 cm. Min.

90 cm. Max.

IMPORTANT: The distance from the floor to the

highest part of the hose should be between 60 to

90 cm. (It is advised to be between 60 and 70 cm).

The hose must not be bent nor twisted to avoid

clogging. Should a prolongation of the discharging

hose be unavoidable this must never surpass 1.5 m

and must be of the same diameter as the original

hose.

Make sure the hoses are not too tense.

Levelling

Level the appliance by loosening or tightening the

feet. Once in the right position fix the feet by

pushing the nuts against the base of the case.

Accurate levelling will prevent vibration, noise and

displacement of the appliance during operation.

Some vibration is inevitable, especially if placed on

a wooden floor. Wooden floors are particularly

susceptible to vibrations. For advice, consult a

builder. If posible always place the appliance on a

solid floor.

Electrical connections

Before plugging the appliance make sure that:

1º. the mains of your installation is the same as on

the rating plate of your appliance (the plate is

sticked to the rear of the appliance).

2º. The meter, the fuses, the wiring and the socket

outlet can support the max. power absorbed stated

on the rating plate.

3º. The socket base and the plug must fit in

adequately without any reducing interposition,

multiple outlets or adapters. If necessary replace

the socket outlet by an adequate one.

The applicable rules for electrical security

require an adequate earthing. The plug of the

appliance is provided with such a device.

Make sure your socket outlet is provided with

an adequate earthing too.

The manufacturer declines any liability in case

of accidents or incicents should these safety

measures not be observed.

The power supply cable only can be replaced by

a person of our Service Force Centre.

P0254

35.292.988…FAE1026V.qxd 30/06/2005 19:43 Página 8

This new machine meets all modern requirements for effective treatment of laundry with low water, energy and

detergent consumption.

•The balance control device ensures the machine is stable during the spin.

1 Detergent dispenser drawer

2 Programme chart

3 Control panel

4 Door handle

5 Drainage area door

6 Adjustable feet

Detergent dispenser drawer

Prewash

Main wash

Fabric softener, starch

Your new washing machine

Description of the appliance

R0001 3D

35.292.988…FAE1026V.qxd 30/06/2005 19:43 Página 9

Use

1. Detergent dispenser drawer

Programme option buttons

Depending on the programme, different option

buttons can be combined.

When these buttons are pressed, the corresponding

lights come on. When they are pressed again, the

lights go off.

If an incompatible option with the selected

programme has been chosen, the corresponding

light flashes for about 2 seconds.

The option buttons:

PRE-WASH or QUICK WASH;

EASY IRON and HALF LOAD

must be selected after the required programme has

been chosen, by turning the programme selector

(see section 9) and before starting the machine, by

pressing button START / PAUSE.

PRE-WASH or QUICK WASH

By pressing this button you have the possibility of

choosing between the following options:

•PRE-WASH option: Adds a pre-wash phase

at the start of the cycle with water heating to 30° C.

In COTTON and SYNTHETIC cycles, performs a

short spin before passing to the washing phase.

This option cannot be selected for WOOL.

•QUICK WASH option: Using this option, you

can get good washing results in a short period of

time, since with option, the COTTON,

SYNTHETICS, and DELICATES programmes are

modified in order to obtain short washing times

(recommended for small or lightly-soiled loads).

This modification consists of reducing the number of

rinse cycles (one less) and also increases the water

level used in the remaining two rinse cycles.

If both lights ( PRE-WASH and QUICK

WASH) are not illuminated the programme will run

without either PRE-WASH or QUICK

WASH).

3. EASY IRON button

This option is available for COTTON, LINEN and

SYNTHETIC programmes. By selecting this button

the machine will inserts a impulse spin and an

anticrease phase after final spin in COTTON

programs. In SYNTHETIC programs, by selecting

this button the machine will inserts a cool-down after

washing phase and an anticrease phase after final

spin.

In case you want to avoid wrinkles in your laundry

after washing,the EASY IRON option must be

selected.

4. HALF LOAD button

Select this button to reduce water consumption on

the rinse cycle when washing a smaller load of

cottons or linens (maximum load size = 2.25 kg).

The machine will perform 2 rinses instead of 3.

5. START / PAUSE button

After selecting the required programme, by the

programme selector (see section 9), press this

button to start the machine; the corresponding light

stops flashing and will keep lighting until the

programme finishes.

To interrupt the running programme, depress

START / PAUSE button: the corresponding

light starts to flash.

To restart the programme from the point at which it

was interrupted, press START / PAUSE button

again.

Control panel

35.292.988…FAE1026V.qxd 30/06/2005 19:43 Página 10

Inhaltsverzeichnis

Andere Zanussi Electrolux Waschmaschine Handbücher

Zanussi Electrolux

Zanussi Electrolux ZWF1421W Bedienungsanleitung

Zanussi Electrolux

Zanussi Electrolux U31302 ZWF 16581 Bedienungsanleitung

Zanussi Electrolux

Zanussi Electrolux ZWF 1651W Bedienungsanleitung

Zanussi Electrolux

Zanussi Electrolux ZWT 8121 Bedienungsanleitung

Zanussi Electrolux

Zanussi Electrolux ZWF 1012 W Bedienungsanleitung

Zanussi Electrolux

Zanussi Electrolux ZWF1421W Bedienungsanleitung

Zanussi Electrolux

Zanussi Electrolux FA5423 Bedienungsanleitung

Zanussi Electrolux

Zanussi Electrolux ZWF 1011 W Bedienungsanleitung

Zanussi Electrolux

Zanussi Electrolux ZWT6021 Bedienungsanleitung

Zanussi Electrolux

Zanussi Electrolux F855 Bedienungsanleitung

Zanussi Electrolux

Zanussi Electrolux ZWA 5120 Bedienungsanleitung

Zanussi Electrolux

Zanussi Electrolux ZWV 1651S Bedienungsanleitung

Zanussi Electrolux

Zanussi Electrolux ZWF 14109 Bedienungsanleitung

Zanussi Electrolux

Zanussi Electrolux FXC 1206 Bedienungsanleitung

Zanussi Electrolux

Zanussi Electrolux ZWA 385 Bedienungsanleitung

Zanussi Electrolux

Zanussi Electrolux F1045 W Bedienungsanleitung

Zanussi Electrolux

Zanussi Electrolux ELECTROLUX ZWT 10120 Bedienungsanleitung

Zanussi Electrolux

Zanussi Electrolux FBU85 Bedienungsanleitung

Zanussi Electrolux

Zanussi Electrolux F1003W Bedienungsanleitung

Zanussi Electrolux

Zanussi Electrolux ZWC 1300W Bedienungsanleitung

Zanussi Electrolux

Zanussi Electrolux ZWF 1630 W Bedienungsanleitung

Zanussi Electrolux

Zanussi Electrolux F 1415 Bedienungsanleitung

Zanussi Electrolux

Zanussi Electrolux IZ12 Bedienungsanleitung

Zanussi Electrolux

Zanussi Electrolux FD 1026 Bedienungsanleitung

Beliebte Waschmaschine Handbücher anderer Marken

Tricity Bendix

Tricity Bendix AW 1000 W Produkthandbuch

Panasonic

Panasonic NA-F60L5WRB Bedienungsanleitung

GE WSLP1500 Handbuch

Electrolux

Electrolux EWF1284EDW Bedienungsanleitung

Bosch

Bosch WAN2829BSN Bedienungsanleitung

LG TV2516DV3B Bedienungsanleitung

LG TH2517DSAV Bedienungsanleitung

VESTEL

VESTEL CMH-XL 7510 TE Bedienungsanleitung

AEG

AEG 74335 Bedienungsanleitung

Johnson

Johnson JWF721A Bedienungsanleitung

Beko

Beko WTE7604XLW0 Bedienungsanleitung

Danby

Danby DTT100A1WDB Montageanleitung

Amica

Amica WA 14 Ex Bedienungsanleitung

Daewoo

Daewoo DWD-F1222 Bedienungsanleitung

Bosch

Bosch WAS28461AU Bedienungsanleitung

Miele

Miele PW 6080 Vario Bedienungsanleitung

Finlux

Finlux FLX108CF220 Bedienungsanleitung

Whirlpool

Whirlpool 3LBR5132AN0 Bedienungsanleitung