Zcom XV-5850 Bedienungsanleitung
802.11a Wireless LAN Access Point XV-5850
User’s Manual
Version 1.1 -July. 2007
CONTENTS
Introduction ............................................................……...............……........2
Hardware Installation ............................................…….......…….................3
WAB102 AP Default Setting……….……………………………………….4
Web Management Settings ………………………………………………..5
Start - Up & Log in ………………………………………………………….5
Main Page …………………………………………………………………...5
Setup …………...…………………………………………………………....6
Password…………….…..…………………………………………………...7
WEP Security ……...………………………………………………………...8
Access Control…………………………………………………………….…9
Advance Setup…………...…………………………………………………10
Factory Default…..…………………………………………………………12
Firmware Upgrade …………………………………………………………12
Status….………….…………………………………………………………13
Troubleshooting ……………………………………………………………14
Technical Specifications .……………………………………………………16
Introduction
Thank you for purchasing your WAB102 802.11a Wireless AP.
This manual will assist you with the installation procedure.
The package you have received should contain the following items:
•WAB102 802.11a Wireless AP……………….……………………………..x1
•User’s Manual…………………………………………………………………x1
•Power Adapter…………………………………………………………………x1
If any of the above items are not included or damaged, please contact your local vendor fo
r
support.
Safety Notification
Your Wireless AP should be placed in a safe and secure location. To ensure proper operation,
please keep the unit away from water and other damaging elements.
Please read the user manual thoroughly before you install the device.
The device should only be repaired by authorized and qualified personnel.
Please do not try to open or repair the device yourself.
Do not place the device in a damp or humid location, i.e. a bathroom.
The device should be placed in a sheltered and non-slip location within a temperature
range of +5 to +40 Celsius degree.
Please do not expose the device to direct sunlight or other heat sources. The housing and
electronic components may be damaged by direct sunlight or heat sources.
Hardware Installation
Front Panel
The front panel provides LED’s for device status. Refer to the following table
for the meaning of each feature.
Rear Panel
LED STATUS Description
Power Off No Power
On Power on
Status Blink 1. Power up 2. firmware upgrade
Off no Ethernet link detected
Green On 100Mbps Fast Ethernet link detected. No activity.
Green
Blink
Ethernet Indicates data traffic on the 100 Mbps LAN
Amber On 10 Mbps Ethernet link detected but no activity
Amber
Blink
Indicates data traffic on the 10 Mbps LAN
Indicates the device is linking or active data
through wireless links
11a Blink
The rear panel features 1 LAN port and Factory Reset button. Refer to the
following table for the meaning of each feature.
WAB102 AP Default Settings
The default settings are shown following.
admin
User Name
default
Password
SystemName 00 60 B3 xx xx xx where xx
xx xx are the last six digits of
the AP’s MAC address
192.168.1.20
AP IP Address
AP Subnet Mask 255.255.255.0
Wireless
ESSID for both 11a&b
11a RF Channel Best
11b RF Channel best
RF Roaming Enabled
Encryption Disabled
MAKE CORRECT NETWORK SETTINGS OF YOUR COMPUTER
To change the configuration, use Internet Explorer (IE) or Netscape Communicator to connect
the WEB management 192.168.1.20. Administrator’s Password default is default.
Main Page
Here allow user to configure basic network settings.
AP Setup
Setup
The Setup page allow user to do basic setting. Enter your wireless network’s SSID, select the
channel at which the network broadcasts its wireless signal, and enter a unique access point
name for the Access Point. Press Apply to save the settings.
Access Point Name: You may assign any name to the Access Point. Unique, memorable names
are helpful, especially if you are employing multiple access points on the same network.
IP Address: This IP address must be unique to your network. (The default IP address of
192.168.1.20)
Subnet Mask:The Access Point’s Subnet Mask must be the same as your Ethernet network.
Default Gateway: Specifics the default gateway for the AP.
DHCP Client: If DHCP is enabled, the IP Address field displays the IP Address that is
dynamically assigned to the AP by the network DHCP server and the IP Mask field
displays the IP Mask utilized by the network DHCP server. Default: Disable
SSID: The SSID is the name shared among all points in a wireless network. The SSID must be
identical for all points in the wireless network. It is case sensitive and must not exceed 32
characters, which may be any keyboard character. Make sure this setting is the same for all
points in your wireless network.
Channel: Select the appropriate channel from the list provided to correspond with your
network settings.
Turbo Mode: When you enable the Turbo Mode, the maximum data rate can up to 72 mbps.
Date Rate: The basic transfer rates should be set depending on the speed of your wireless
network Specifies rate of data transmission. Select the desired rate from the drop-down menu.
The best selection will adapt the rate to the best available.
Outdoor Channels: Enable the AP to interface with STAs using those specific frequencies
which are allowed for outdoor use.
Click the Reboot button for changes to take effect. After you click Reboot button, the web
server will lose connectivity with the AP Web Server as the AP reboots. To reestablish the
connection with the AP Web Server, please wait until the AP has completed rebooting and
navigate to the Web Server to resume communication.
Password
Here allow you to change the Access Point’s password. Changing the password for the Access
Point is as easy as typing the password into the New Password field. Then, type it again into
the Retype new password field to confirm. Click the Apply button to save the setting.
Web Security
To prevent unauthorized wireless stations from accessing data transmitted over the network,
the WAB102 Web Security Configuration window offers highly data encryption, known as
WEP, making your data transmission over air more secure and allows you to specify
Encryption Key(s) if you enable encryption for the AP.
Authentication Type: Open System: The Authentication Type default is set to Open System.
It is recommended that you use the default setting. Shared Key: Shared Key is when both the
sender and the recipient share a secret key. All points on your network must use the same
authentication type.
WEP: The WEP Encryption method is Disable by default. To enable WEP, click the
Enable radio button. From the pull-down menu at the top of the screen, select 64-bit, 128-
b
it, or
152 bit encryption. The Encryption key is in Hexadecimal format. Hexadecimal characters on
your keyboard are the letters “A-F” and the numbers “ 0- 9” Click the Apply button to save the
setting.
Click the Reboot button for changes to take effect. After you click Reboot button, the web
server will lose connectivity with the AP Web Server as the AP reboots.
Access Control
The Access Control tab, allows you to block or allow certain computers by their MAC Address.
To enable filtering of computers by their MAC Addresses, click the Allow MAC address(es) in
list radio button. Enter MAC Address and click Add button. Click Delete button if you wish to
remove the MAC address from the list. To disable this feature, click the radio button by
Disable.
Inhaltsverzeichnis
Andere Zcom Drahtloser Zugangspunkt Handbücher
Zcom
Zcom SP250 Bedienungsanleitung
Zcom
Zcom XG-1020 Bedienungsanleitung
Zcom
Zcom AC-1025D Bedienungsanleitung
Zcom
Zcom AS220V2 Bedienungsanleitung
Zcom
Zcom SP420 Series Bedienungsanleitung
Zcom
Zcom SP230 Series Bedienungsanleitung
Zcom
Zcom SP230 Series Bedienungsanleitung
Zcom
Zcom AS420 Bedienungsanleitung
Zcom
Zcom SP220V2 Series Bedienungsanleitung
Zcom
Zcom ZAC-1023-5 Bedienungsanleitung
Zcom
Zcom ZAC-1023-2 Bedienungsanleitung
Zcom
Zcom AS220V2 Bedienungsanleitung
Zcom
Zcom ZAC Series Bedienungsanleitung
Zcom
Zcom XG-3120 Bedienungsanleitung
Zcom
Zcom XG-580 PLUS Bedienungsanleitung
Zcom
Zcom AC-1028 Bedienungsanleitung
Zcom
Zcom SP230 Series Bedienungsanleitung
Zcom
Zcom ZCN-1523H-2-8 Bedienungsanleitung
Zcom
Zcom AS220V2 Bedienungsanleitung
Zcom
Zcom ZN-7100-DE500-G V4 Bedienungsanleitung
Beliebte Drahtloser Zugangspunkt Handbücher anderer Marken
D-Link
D-Link DWL-2100AP - AirPlus Xtreme G Bedienungsanleitung
Ubiquiti
Ubiquiti NanoStation NSM2 Bedienungsanleitung
Cisco
Cisco Aironet 1550 Series Bedienungsanleitung
Aruba
Aruba IAP-335 Bedienungsanleitung
Advantek Networks
Advantek Networks AWN-AP-54MR Bedienungsanleitung
IP-COM
IP-COM AP355 Bedienungsanleitung
Buffalo
Buffalo AirStation WLA-L11G Bedienungsanleitung
EnGenius
EnGenius EnStationACv2 Bedienungsanleitung
D-Link
D-Link DAP-3662 Bedienungsanleitung
xG Technology
xG Technology xMax CN1300 Bedienungsanleitung
Widelink
Widelink ezWave WAP-1100 Series Bedienungsanleitung
Edimax
Edimax CAP1200 Bedienungsanleitung
