Zennio ACTinBOX MAX6 Bedienungsanleitung

ACTinBOX MAX6

6 Outputs Actuator

ZN1IO-AB60

Program version: 3.0

Manual edition: a

PRODUCT MANUAL

ZENNiO AVANCE Y TECNOLOGÍA vwww.zennio.com

INDEX

1. Introduction ..............................................................................................................................................3

1.1. ACTinBOX MAX6.............................................................................................................................. 3

1.2. Installation......................................................................................................................................4

2. Configuration.............................................................................................................................................5

2.1. Individual outputs ........................................................................................................................... 5

2.2. Shutter channels.............................................................................................................................6

2.3. Relay control using IR remote..........................................................................................................7

3. ETSParameterization.................................................................................................................................9

3.1. Defaultconfiguration ...................................................................................................................... 9

3.2. Outputs......................................................................................................................................... 10

3.2.1. Individual outputs.................................................................................................................. 11

3.2.2. Shutter channel..................................................................................................................... 18

3.3. Logical functions............................................................................................................................ 29

Annex I. Slats precise control........................................................................................................................ 30

Annex II. Communication objects.................................................................................................................. 34

ZENNiO AVANCE Y TECNOLOGÍA vwww.zennio.com

1. INTRODUCTION

1.1. ACTINBOX MAX6

ACTinBOX MAX6 is a KNX actuator that combines in a same device the following features:

6 multifunction binary outputs (relay outputs), with 10A each, configured as:

Up to 3 shutter channels (with or without slats).

Up to 6 individual outputs.

10 multi operational logical functions module, which may be enabled or disabled

independently by means of a communication object.

Manually operating over the actuator outputs, by means of the Zennio infrared remote

control.

The outputs and the logical functions module work independently and can interact the others as if

they were two autonomous devices connected to the KNX bus.

Figure 1.1. ACTinBOX MAX6 Actuator

ZENNiO AVANCE Y TECNOLOGÍA vwww.zennio.com

1.2. INSTALLATION

ACTinBOX MAX6 connects to the KNX bus through the included KNX connector.

Once the device is provided with power supply from the KNX bus, both the physical address and the

associated application program can be downloaded.

This actuator does not need any additional external power supply since it is powered through the

KNX bus.

Figure 1.2. ACTinBOX MAX6. Elements scheme

It is described below the functionality of the main elements of the actuator:

Programming button (2): a short press on this button set the actuator in programming

mode, and the associated LED (3) lights red. (Note: If this button is held while plugging the

device into de KNX bus, ACTinBOX MAX6 goes into secure mode. The LED blinks red every

0.5 seconds).

Outputs (1): the terminal blocks with screws (included in the original package) must be

plugged here to allow connecting the different systems to be controlled by the actuator. The

terminal blocks wiring may be carried out before inserting them in the corresponding points.

To obtain more detailed information about the technical features of ACTinBOX MAX6, as well as

security and installation information, please read the actuator Datasheet, included in the original

package of the device and also available at: http://www.zennio.com.

Outputs

2.- Programming button

3.- Programming LED

4.- KNX connector

ZENNiO AVANCE Y TECNOLOGÍA vwww.zennio.com

2. CONFIGURATION

2.1. INDIVIDUAL OUTPUTS

ACTinBOX MAX6 has 6 relay outputs that allow the control of different charges

autonomously. Each output can be enabled or disabled independently.

Every individual output can be configured as normally open (the output is ON when its relay

closes) or normally closed (the output is ON when its relay opens).

Besides the type, ACTinBOX MAX6 allows the configuration of the following functionalities of the

individual outputs:

Timers. This section is meant to control the outputs by means of a timer, setting times for

the ON and OFF of the output.

Scenes. Allows running and/or saving a specific action over the output/s where this

function is enabled. The status of the outputs will vary depending on the action set by the

parameterized scene.

Alarm. Allows changing the output status where this function is enabled. It can be

configured the status on which the output will be set both for the alarm activation and for the

alarm deactivation.

Note: The alarm has priority over the rest of functionalities.

Start-up configuration Default or custom.

All these configuration options are explained in detail in the section 3. ETS Parameterization.

ZENNiO AVANCE Y TECNOLOGÍA vwww.zennio.com

2.2. SHUTTER CHANNELS

ACTinBOX MAX6 allows installing up to 3 different shutter drive control (or similar) on its

channels.

These channels allow controlling the shutter movements in a domotic installation.

Basic control: lower/raise the shutter

Precise control: precise controlling of the shutter and the slats (for blinds with slats)

Each channel (associated to a letter from A to C) consists of two consecutive individual outputs; i.e.,

Channel A includes the individual outputs 1 and 2; the channel B, 3 and 4 and the channel C, the

outputs 5 and 6. The first output of the channel sends the order to raise the shutter, whereas the

second one sends the order to lower the shutter. Therefore, the motor cables of the shutters, in

charge of carrying out these actions, should be properly connected to each output of the channel to

perform the required action.

The Table 1.1 shows the action carried out by the outputs of each channel:

Channel Outputs Action

A 1 Raise

2 Lower

B 3 Raise

4 Lower

C 5 Raise

6 Lower

Table 1.1. Shutter channels: actions of the outputs

Each channel can be configured as Shutter (No Slats) or as Blind (with Slats).

Besides the type of shutter, ACTinBOX MAX6 allows the configuration of the following

functionalities of the shutter channels:

Times. Allows configuring the main times associated to the movement of a shutter: time

up and time down, and also the definition of a security time to pause the movement when the

direction changes, and an additional time when the shutter gets its limit (top or bottom). For

blinds with slats, it is also possible to configure the secondary time, referred to the slats length

and the slats step time.

ZENNiO AVANCE Y TECNOLOGÍA vwww.zennio.com

Status objects. Reports on the actual position of the shutter.

Precise control. Allows moving the shutter to any position (in percentage: 0-100%,

defined by parameter) on its length. Moreover, for blinds with slats, it is also possible to

establish a desired position for the slats (value between 0% and 100%).

Scenes. Allows running and/or saving a specific action over the channel/s where this

function is enabled.

Alarms. Two alarms available for each shutter channel. They execute the action defined

by parameter when receiving a specific external event.

Reversed moving. It makes possible to control shutters the other way around from usual.

Direct positioning. Function to move a shutter to a prefixed specific position via 1 bit

communication object.

Start-up configuration. Default or custom.

All these configuration options are explained in detail in the section 3. ETS Parameterization.

2.3. RELAY CONTROL USING IR REMOTE

ACTinBOX MAX6 actuator incorporates in its design an infrared receiver, located next to the

programming LED. This functionality allows testing the actuator outputs, during the installation, from

the Zennio infrared remote control (the same used to control the touch panel InZennio Z38i. See

Figure 2.1).

Note: To control the outputs from the IR remote, it is necessary to have the programming LED lit

(lighting red).

The outputs control is carried out as follows:

Push the right button: close the corresponding output relay

Push the left button: open the corresponding output relay

In the Figure 2.1 it is shown a representation of the buttons of the IR remote that must be pressed,

depending on the output to be remote controlled.

ZENNiO AVANCE Y TECNOLOGÍA vwww.zennio.com

Figure 2.1. Pressing zones in the IR remote

The relay control using IR remote is just an output test of the actuator. None of its parameterized

functions (such as scenes, timers, etc.) are taken into account at the moment to open and close the

relays remotely.

ZENNiO AVANCE Y TECNOLOGÍA vwww.zennio.com

3. ETS PARAMETERIZATION

For starting to parameterize the ACTinBOX MAX6 actuator it is necessary, once the ETS

program has been opened, importing the data base of the product (version 3.0 of the application

program).

Next, the device is added to the project where desired. Click the right mouse button on the device

and select "Edit parameters" for starting with the configuration.

In the following sections there is a detailed explanation about each of the different functionalities of

ACTinBOX MAX6 in ETS.

3.1. DEFAULT CONFIGURATION

This section shows the default configuration from which the device parameterization starts.

When entering for the first time to the parameters edition of ACTinBOX MAX6, the following window

will be shown:

Figure 3.1. Configuration screen by default

As seen in figure 3.1, the outputs and the logical functions are disabled by default, so there will be

no communication objects available until the user enables the different functionalities of the

actuator.

If the parameter "Sending of Indication objects on bus voltage recovery" is enabled, two new 1-bit

communication objects will appear ("Reset 0" and "Reset 1"), which allow sending to the KNX bus

the values "0" and "1" after a bus power failure, in order to recover the communication with the rest

of the devices in the installation. This sending may be immediate or after a configured delay (in

seconds).

ZENNiO AVANCE Y TECNOLOGÍA vwww.zennio.com

3.2. OUTPUTS

When selecting “Yes” in the Outputs parameter, the access to the outputs configuration will

appear in the menu on the left side. It looks as follows:

Figure 3.2. Outputs configuration

The outputs are grouped (in pairs) by channels, up to 3, named from A to C, disabled by default.

When selecting one of them, it is shown a drop-down box to configure the outputs as individual

outputs or shutter channels.

Figure 3.3. Possible configurations of the Channels

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Zennio Controller Handbücher

Zennio

Zennio MAXinBOX 8 Plus Leitfaden

Zennio

Zennio MINiBOX 45v2 Bedienungsanleitung

Zennio

Zennio HeatingBOX 230V 4X Leitfaden

Zennio

Zennio ALLinBOX 1612 v2 Bedienungsanleitung

Zennio

Zennio HeatingBOX 230V 4X Leitfaden

Zennio

Zennio MAXinBOX 66 Bedienungsanleitung

Zennio

Zennio IRSC Plus Bedienungsanleitung

Zennio

Zennio MAXinBOX 8 v3 Leitfaden

Zennio

Zennio MAXinBOX 66 Leitfaden

Zennio

Zennio ZoningBOX 6 Leitfaden

Zennio

Zennio LUMENTO X3 Leitfaden

Zennio

Zennio MAXinBOX 24 v2 Leitfaden

Zennio

Zennio MAXinBOX66 Leitfaden

Zennio

Zennio MAXinBOX 66 Bedienungsanleitung

Zennio

Zennio MAXinBOX 8 Plus Leitfaden

Zennio

Zennio ZoningBOX 6 Bedienungsanleitung

Zennio

Zennio FANinBOX 230V 1CH Leitfaden

Zennio

Zennio ZCL-8HT230 Bedienungsanleitung

Zennio

Zennio MAXinBOX 16 Plus Leitfaden

Zennio

Zennio IRSC Zone Bedienungsanleitung

Zennio

Zennio Roll-ZAS Bedienungsanleitung

Zennio

Zennio MAXinBOX 24 ZIO-MB24 Bedienungsanleitung

Zennio

Zennio MAXinBOX 8 Leitfaden

Zennio

Zennio MAXinBOX SHUTTER 4CH Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1769-L31 Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Samson

Samson Type 5824 Service-Handbuch

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Fishman

Fishman TriplePlay Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung