Zennio MAXinBOX 8 v3 Leitfaden

MAXinBOX 8 v3

Multifunction actuator with 8 outputs (16A)

ZIOMB8V3 TECHNICAL DOCUMENTATION

FEATURES

•2 different configurable blocks: shutter channels (up to 4), individual

outputs (up to 8) and 2-pipe fan coil control (up to 2)

•Outputs suitable for capacitive loads, maximum 140 µF.

•Manual output operation with push button and LED Status indicator.

•20 logic functions.

•Output timing.

•Total data saving on KNX bus failure.

•Integrated KNX BCU.

•Dimensions 67 x 90 x 79mm (4.5 DIN units).

•DIN rail mounting (EN 50022), with fixing clamp.

•Possibility of connecting different phases in adjacent outputs.

•Conformity with the CE directives (CE-mark on the right side).

1. Upper outputs

2. Lower outputs

3. Programming/test LED

4. KNX Connector

5. Fixing clamp

6. Programming/test button

7. Output control button

8. Output status LED indicator

Figure 1: MAXinBOX 8 v3

Programming/Test button: short press to set programming mode. If this button is held while plugging the device into the KNX bus, it enters the safe

mode. If this button is held for more than 3 seconds, the device enters the test mode.

Programming/Test LED: programming mode indicator (red). When the device enters the safe mode, it blinks (red) every half second. The manual mode

is indicated by the green color. During the start-up (reset or after KNX bus failure)and if the device is notin safe mode, it startsa blue blinking sequence.

GENERAL SPECIFICATIONS

CONCEPT

DESCRIPTION

Type of device

Electric operation control device

KNX supply

Voltage (typical)

29VDC SELV

Voltage range

21..31VDC

Maximum

consumption

Voltage

29VDC (typical)

116

24VDC¹

240

Connection type

Typical TP1 bus connector for 0.80mm Ø rigid cable

External power supply

Not required

Operation temperature

0°C .. +55°C

Storage temperature

-20°C .. +55°C

Operation humidity

5 .. 95% (No condens.)

Storage humidity

5 .. 95% (No condens.)

Complementary characteristics

Class B

Protection class

Operation type

Continuous operation

Device action type

Type 1

Electrical stress period

Long

Degree of protection

IP20, clean environment

Installation

Independent device to be mounted inside electrical panels with DIN rail (EN

50022)

Minimum clearances

Not required

Response on KNX bus failure

Data saving according to parameterization

Response on KNX bus restart

Data recovery according to parameterization

Operation indicator

The programming LED indicates programming mode (red) and test mode

(green). Each output LED indicates its status

Weight

188g

PCB CTI index

175V

Housing material

PC FR V0 halogen free

¹ Maximum consumption in the worst case scenario (KNX Fan-In model)

SAFETY INSTRUCTIONS

•Installation should only be performed by qualified professionals according to the laws and regulations applicable in each country.

•Do not connect the mains voltage nor any other external voltage to any point of the KNX bus; it would represent a risk for the entire

KNX system. The facility must have enough insulation between the mains (or auxiliary) voltage and the KNX bus or the wires of other

accessories, in case of being installed.

•Once the device is installed (in the panel or box), it must not be accessible from outside.

•Keep the device away from water and do not cover it with clothes, paper or any other material while in use.

•The WEEE logo means that this device contains electronic parts and it must be properly disposed of by following the instructions at

http://zennio.com/weee-regulation.

OUTPUTS SPECIFICATIONS AND CONNECTIONS

CONCEPT

DESCRIPTION

Number of outputs

Output type / Disconnection type

Potential-free outputs through bistable relays with tungsten pre-contact /

Micro-disconnection

Rated current per output

AC 16(6)A @ 250VAC (4000VA)

DC 7A @ 30VDC (210W)

Maximum load per output

Resistive

4000W

Inductive

1500VA

Maximum inrush current

800A/200μs

165A/20ms

Connections in adjacent outputs

Possibility of connecting different phases. It is not allowed to connect power

supplies of different order, SELV with NO SELV, in the same block

Total maximum current in device

80A

Short-circuit protection

Overload protection

Connection method

Screw terminal block

Cable cross-section

1.5-4mm² (IEC) / 26-10AWG (UL)

Outputs per common

Maximum response time

10ms

Mechanical lifetime (min. cycles)

3 000 000

⚠In order to ensure the expected status

of the relays, please check that the

device is connected to the KNX bus

before energizing the power circuit.

WIRINGDIAGRAMS

Figure 2: Wiring example (from left to right): 2 loads, 2 loads

connected to different phases, shutter and fan coil

Attaching MAXinBOX 8 v3 to DIN rail:

Removing MAXinBOX 8 v3 from DIN rail:

Figure 3: Mounting MAXinBOX 8 v3 on DIN rail

Dieses Handbuch passt für folgende Modelle

Andere Zennio Controller Handbücher

Zennio

Zennio MAXinBOX FC 0-10V VALVE Bedienungsanleitung

Zennio

Zennio ZN1CL-IRSC Bedienungsanleitung

Zennio

Zennio HeatingBOX 230V 4X Leitfaden

Zennio

Zennio Roll-ZAS Bedienungsanleitung

Zennio

Zennio MAXinBOX 16 Plus Leitfaden

Zennio

Zennio MAXinBOX 66 v2 Leitfaden

Zennio

Zennio MAXinBOX 66 Bedienungsanleitung

Zennio

Zennio MAXinBOX 16 Leitfaden

Zennio

Zennio MAXinBOX SHUTTER 4CH Bedienungsanleitung

Zennio

Zennio ZCL-FC010F Leitfaden

Zennio

Zennio AudioInRoom ZMU-AUIR Bedienungsanleitung

Zennio

Zennio AudioInRoom Bedienungsanleitung

Zennio

Zennio MINiBOX 0-10V X3 Bedienungsanleitung

Zennio

Zennio ZoningBOX 6 Leitfaden

Zennio

Zennio MAXinBOX 8 Leitfaden

Zennio

Zennio MAXinBOX66 Leitfaden

Zennio

Zennio ALLinBOX 1612 Leitfaden

Zennio

Zennio IRSC Zone Bedienungsanleitung

Zennio

Zennio MAXinBOX FC 0-10V VALVE Bedienungsanleitung

Zennio

Zennio ZIO-IB24 Bedienungsanleitung

Zennio

Zennio ZoningBOX 6 Bedienungsanleitung

Zennio

Zennio ALLinBOX 1612 v2 Bedienungsanleitung

Zennio

Zennio FANinBOX 230V 1CH Leitfaden

Zennio

Zennio ZCL-8HT230 Leitfaden

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1769-L31 Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Samson

Samson Type 5824 Service-Handbuch

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Fishman

Fishman TriplePlay Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung