Zennio EyeZen TP vT Bedienungsanleitung
EyeZen TP vT
https://www.zennio.com Technical Support: https://support.zennio.com
2
CONTENTS
Contents........................................................................................................................................ 2
1 Introduction .......................................................................................................................... 3
1.1 EyeZen TP vT.................................................................................................................. 3
1.2 Installation..................................................................................................................... 4
1.3 Start-Up and Power Loss............................................................................................... 5
2 Configuration......................................................................................................................... 6
2.1 General.......................................................................................................................... 6
2.2 Presence Detector......................................................................................................... 8
2.3 Logic Functions............................................................................................................ 10
ANNEX I. Communication Objects............................................................................................... 11
EyeZen TP vT
https://www.zennio.com Technical Support: https://support.zennio.com
3
1INTRODUCTION
1.1 EYEZEN TP VT
EyeZen TP vT from Zennio is a device that aims at, among other functions, the detection
of presence, the measurement and control of the room luminosity and the detection of
occupancy within the room where it has been installed. It has been designed for ceiling
or false ceiling mounting by means of the bundled accessories.
The most outstanding features of EyeZen TP vT are:
Sensor with configurable sensitivity.
LED to indicate motion.
Two types of lenses: black and white.
Presence detection:
➢6 presence detection channels.
➢Luminosity-dependent presence detection (optional).
➢Periodic and delayed sendings (binary, scene, HVAC, percentage).
Occupancy detection:
➢1x occupancy detection channel.
➢Master / slave configuration.
➢Trigger upon door opening or closing.
➢Periodic and delayed sendings (binary, scene, HVAC, percentage).
Luminosity measurement:
➢Configurable correction factor and offset.
➢Periodic sending or upon value change.
2 constant light control channels with configurable setpoints.
Day / night configuration.
10 customisable, multi-operation logic functions.
Heartbeat or periodical “still alive” notification.
EyeZen TP vT
https://www.zennio.com Technical Support: https://support.zennio.com
4
1.2 INSTALLATION
EyeZen TP vT connects to the KNX bus through the on-board KNX connector.
Once the device is provided with power from the KNX bus, both the individual address
and the associated application program may be downloaded.
This device does not need any additional external power since it is entirely powered
through the KNX bus.
Figure 1. EyeZen TP vT. Elements
The main elements of the device are described next.
Programming button (3): a short press on this button sets the device into the
programming mode, making the associated LED (4) light in red.
Note: if this button is held while plugging the device into the KNX bus, the device
will enter the safe mode. In such case, the LED will blink in red every 0.5
seconds.
Detection notification LED (1): emits a red light flash when the sensor
observes motion.
To get detailed information about the technical features of this device, as well as on the
installation process and on security procedures, please refer to the corresponding
Datasheet, bundled with the original packaging of the device and also available at
www.zennio.com.
1. Detection LED indicator.
2. Retaining spring.
3. Test/Prog. button.
4. Test/Prog. LED.
5. KNX connector.
1
5
2
3
4
EyeZen TP vT
https://www.zennio.com Technical Support: https://support.zennio.com
5
1.3 START-UP AND POWER LOSS
During the start-up of the device, the detection notification LED flashes red for one
minute before the motion sensor is ready.
Depending on the configuration, some specific actions will also be performed during the
start-up. For example, the integrator can set whether the detection channels should start
up enabled or disabled.
EyeZen TP vT
https://www.zennio.com Technical Support: https://support.zennio.com
6
2CONFIGURATION
2.1 GENERAL
After importing the corresponding database in ETS and adding the device into the
topology of the desired project, the configuration process begins by entering the
parameters window of the device.
ETS PARAMETERISATION
From General screen it is possible to activate/deactivate all the required functionality.
Figure 2. General
Presence Detection [enabled]
1
: enables the “Presence Detector” tab in the
tree on the left. For more information, see section 2.2.
Logic Functions [enabled/disabled] enables or disables the “Logic Functions”
tab in the tree on the left. For more information, see section 2.3.
Heartbeat (Periodic Alive Notification) [enabled/disabled]: incorporates a
one-bit object to the project (“[Heartbeat] Object to Send ‘1’”) that will be sent
periodically with a value of “1” to notify that the device is still working (still alive).
Figure 3. Heartbeat
1
The default values of each parameter will be highlighted in blue in this document, as follows:
[default/rest of options].
EyeZen TP vT
https://www.zennio.com Technical Support: https://support.zennio.com
8
2.2 PRESENCE DETECTOR
EyeZen TP vT incorporates six independent presence detection channels, two more for
constant light control and one for occupancy detection.
Presence detection consists in sending objects to the bus whenever the
device observes a moving body (or no longer observes it) in the environment
of the room where it has been installed.
Constant light control consists in sending KNX orders to the dimmer device
that controls the in-room luminaries so the ambient light level remains constant
even if other light sources are present.
Occupancy detection is an algorithm that allows determining whether a
particular space is under occupation no matter if the occupant moves or not
(i.e., no matter if the device is detecting presence in the room or not).
It also allows setting different luminosity setpoints or object types for daytime and night
time as well as activating or deactivating the motion indicator LEDs.
EyeZen TP vT can also set custom sensitivity of the motion sensor and measure the
luminosity of the room by making certain adjustments. This measurement will be made
according to the type of lens selected.
Please refer to the specific manual “Presence Detector” available in EyeZen TP vT
product section at the Zennio website (www.zennio.com) for detailed information about
the functionality and the configuration of the related parameters.
ETS PARAMETERISATION
In Presence Detector screen, additional to the parameters of this functionality, lens type
parameter is included.
EyeZen TP vT
https://www.zennio.com Technical Support: https://support.zennio.com
10
2.3 LOGIC FUNCTIONS
This module makes it possible to perform numeric and binary operations to incoming
values received from the KNX bus, and to send the results through other communication
objects specifically enabled for this purpose.
EyeZen TP vT can implement up to 10 different and independent functions, each of
them entirely customisable and consisting of up to 4 consecutive operations.
The execution of each function can depend on a configurable condition, which will be
evaluated every time the function is triggered through specific, parameterisable
communication objects. The result after executing the operations of the function can also
be evaluated according to certain conditions and afterwards sent (or not) to the KNX
bus, which can be done every time the function is executed, periodically or only when
the result differs from the last one.
Please refer to the “Logic Functions” user manual available under the EyeZen TP vT
product section at the Zennio homepage (www.zennio.com) for detailed information
about the functionality and the configuration of the related parameters.
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere Zennio Sicherheitssensor Handbücher
Zennio
Zennio WinDoor RF Bedienungsanleitung
Zennio
Zennio EyeZen TP Bedienungsanleitung
Zennio
Zennio ZN1IO-DETEC Bedienungsanleitung
Zennio
Zennio EyeZen TP v2 Bedienungsanleitung
Zennio
Zennio Presentia W0 Bedienungsanleitung
Zennio
Zennio Presentia C v2 Bedienungsanleitung
Zennio
Zennio Presentia C v2 Bedienungsanleitung
Zennio
Zennio Presentia W0 Bedienungsanleitung
Zennio
Zennio EyeZen RF ZPDEZRF868 Bedienungsanleitung
Zennio
Zennio WinDoor RF Leitfaden
