Zennio Presentia W0 Bedienungsanleitung

Presentia W0

Presence Detector with Luminosity Sensor

for Wall Mounting

ZPDW0

USER MANUAL

Application program version: [1.0]

User manual edition: [1.0]_a

www.zennio.com

Presentia W0

http://www.zennio.com Technical Support: http://support.zennio.com

CONTENTS

Contents........................................................................................................................................ 2

1 Introduction .......................................................................................................................... 3

1.1 Presentia W0................................................................................................................. 3

1.2 Installation..................................................................................................................... 4

1.3 Start-Up and Power Loss............................................................................................... 6

2 Configuration......................................................................................................................... 7

2.1 General.......................................................................................................................... 7

2.1.1 Configuration..................................................................................................... 7

2.2 Presence Detector......................................................................................................... 9

2.3 Logic Functions............................................................................................................ 10

ANNEX I. Communication Objects............................................................................................... 11

Presentia W0

http://www.zennio.com Technical Support: http://support.zennio.com

1INTRODUCTION

1.1 PRESENTIA W0

Presentia W0 from Zennio is a device that aims at, among other functions, the

detection of presence, the measurement and control of the room luminosity and the

detection of occupancy within the room where it has been installed. It has been

designed for wall mounting by means of the bundled accessories.

The most outstanding features of Presentia W0 are:

2 available colours, white and black.

2 sensors with configurable sensitivities.

1 LED to indicate motion.

Presence detection:

➢6 presence detection channels.

➢Luminosity-dependent presence detection (optional).

➢Periodic and delayed sendings (binary, scene, HVAC, percentage).

Occupancy detection:

➢1x occupancy detection channel.

➢Master / slave configuration.

➢Trigger upon door opening or closing.

➢Periodic and delayed sendings (binary, scene, HVAC, percentage).

Luminosity measurement:

➢Periodic sending or upon value change.

➢Sending of luminosity-dependent notifications.

Day / night configuration.

10 customisable, multi-operation logic functions.

Heartbeat or periodic “still alive” notification.

Presentia W0

http://www.zennio.com Technical Support: http://support.zennio.com

1.2 INSTALLATION

Presentia W0 connects to the KNX bus through the on-board KNX connector.

Once the device is provided with power from the KNX bus, both the individual address

and the associated application program may be downloaded.

This device does not need any additional external power since it is entirely powered

through the KNX bus.

Figure 1. Presentia W0. Elements

The main elements of the device are described next.

Programming button (5): a short press on this button sets the device into

the programming mode, making the associated LED (4) light in red.

Note: if this button is held while plugging the device into the KNX bus, the

device will enter the safe mode. In such case, the LED will blink in red every

0.5 seconds.

Detection notification LED (2): emits a light flash whenever the sensor

associated to that zone observes motion.

Note: for an optimal operation of the presence and luminosity sensors it is

recommended that this detection notification LED only be activated during the

installation process.

55,5

40 32

55,5

40 32

1. Frame.

2. Detection notification LED.

3. Fixing clip.

4. Programming LED.

5. Programming button.

6. KNX connector.

7. Levelling plates (1 y 1,5mm)

Presentia W0

http://www.zennio.com Technical Support: http://support.zennio.com

To get detailed information about the technical features of this device, as well as on the

installation process and on security procedures, please refer to the corresponding

Datasheet, bundled with the original packaging of the device and also available at

www.zennio.com.

Presentia W0

http://www.zennio.com Technical Support: http://support.zennio.com

1.3 START-UP AND POWER LOSS

During the start-up of the device, the detection notification LED flashes red for one

minute before the motion sensor is operational.

Depending on the configuration, some specific actions will also be performed during

the start-up. For example, the integrator can set whether the detection channels should

start up enabled or disabled.

Presentia W0

http://www.zennio.com Technical Support: http://support.zennio.com

2CONFIGURATION

After importing the corresponding database in ETS and adding the device into the

topology of the desired project, the configuration process begins by entering the

parameters window of the device

2.1 GENERAL

This window is subdivided into several other sections, which contain different general

parameters.

2.1.1 CONFIGURATION

ETS PARAMETERISATION

From “General”tab all the required functionality can be activated/deactivated.

Figure 2. General

Lens Color [White / Black]

: selects the lens colour depending on Presentia

W0 type (white or black), allowing a correct measurement of luminosity and

detections through the sensors.

Presence Detection [enabled/disabled]: enables the “Presence Detector” tab

in the tree on the left. For more information, see section 2.2.

Logic Functions [enabled/disabled] enables or disables the “Logic

Functions” tab in the tree on the left. For more information, see section 2.3.

The default values of each parameter will be highlighted in blue in this document, as follows:

[default/rest of options].

Presentia W0

http://www.zennio.com Technical Support: http://support.zennio.com

Heartbeat (Periodic Alive Notification) [enabled/disabled]: incorporates a

one-bit object to the project (“[Heartbeat] Object to Send ‘1’”) that will be

sent periodically with a value of “1” to notify that the device is still working (still

alive).

Figure 3. Heartbeat

Note: the first sending after download or bus failure takes place with a delay

of up to 255 seconds, to prevent bus overload. The following sendings

match the period set.

Ambient Luminosity Sensor [enabled/disabled]: enables or disables the

ambient luminosity sensor. When enabled, a new tab is added in the tree on

the left. For more information, see section 2.1.1.1.

2.1.1.1 AMBIENT LUMINOSITY SENSOR

Presentia W0 incorporates a luminosity sensor to receive and monitor ambient

luminosity measurement.

Please refer to the specific manual “Luminosity and Proximity Sensor” (available in

the Flat Display product section at the Zennio homepage, www.zennio.com) for

detailed information about the functionality and the configuration of the related

parameters.

Note: Proximity functionality, described in the "Luminosity and Proximity Sensor"

manual, is not included in Presentia W0.

Presentia W0

http://www.zennio.com Technical Support: http://support.zennio.com

2.2 PRESENCE DETECTOR

Presentia W0 incorporates six independent presence detection channels and one for

occupancy detection.

Presence detection consists in sending objects to the bus whenever the

device observes a moving body (or no longer observes it) in the environment

of the room where it has been installed.

Occupancy detection is an algorithm that allows determining, through a

multiple sensor configuration, whether a particular space is under occupation

no matter if the occupant moves or not (i.e., no matter if the device is

detecting presence in the room or not).

It also allows setting different luminosity setpoints or object types for day and night

time as well as activating or deactivating the motion indicator LEDs.

Presentia W0 can also set custom sensitivity of the motion sensor and measure the

luminosity level of the room. This measurement will be made according to the colour

of lens selected.

Please refer to the specific manual “Presence Detector” available in Presentia W0

product section at the Zennio website (www.zennio.com) for detailed information about

the functionality and the configuration of the related parameters.

Please note:

The constant light regulation functionality is not included (the working plane

on which the device is installed is not suitable for this functionality).

The unit of measurement for the luminosity level is percentage.

Presentia W0

http://www.zennio.com Technical Support: http://support.zennio.com

2.3 LOGIC FUNCTIONS

This module makes it possible to perform numeric and binary operations to incoming

values received from the KNX bus, and to send the results through other

communication objects specifically enabled for this purpose.

Presentia W0 can implement up to 10 different and independent functions, each of

them entirely customisable and consisting of up to 4 consecutive operations.

The execution of each function can depend on a configurable condition, which will be

evaluated every time the function is triggered through specific, parameterisable

communication objects. The result after executing the operations of the function can

also be evaluated according to certain conditions and afterwards sent (or not) to the

KNX bus, which can be done every time the function is executed, periodically or only

when the result differs from the last one.

Please refer to the “Logic Functions” user manual available under the Presentia W0

product section at the Zennio homepage (www.zennio.com) for detailed information

about the functionality and the configuration of the related parameters.

Andere Handbücher für Presentia W0

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Zennio Sicherheitssensor Handbücher

Zennio

Zennio WinDoor RF Bedienungsanleitung

Zennio

Zennio WinDoor RF Leitfaden

Zennio

Zennio Presentia C v2 Bedienungsanleitung

Zennio

Zennio Presentia W0 Bedienungsanleitung

Zennio

Zennio EyeZen TP Bedienungsanleitung

Zennio

Zennio EyeZen TP v2 Bedienungsanleitung

Zennio

Zennio EyeZen RF ZPDEZRF868 Bedienungsanleitung

Zennio

Zennio EyeZen TP vT Bedienungsanleitung

Zennio

Zennio Presentia C v2 Bedienungsanleitung

Zennio

Zennio ZN1IO-DETEC Bedienungsanleitung

Beliebte Sicherheitssensor Handbücher anderer Marken

THORLABS

THORLABS PDA10JT Bedienungsanleitung

Waeco

Waeco UV-DETECT Bedienungsanleitung

Intermatic

Intermatic IOS-DSIMF Bedienungsanleitung

urmet domus

urmet domus 1083 Bedienungsanleitung

Siemens

Siemens AZL66 Series Bedienungsanleitung

BTI

BTI Profiline Multi Finder Bedienungsanleitung

Challenger

Challenger SL01 Bedienungsanleitung

DMP Electronics

DMP Electronics 1122INT Bedienungsanleitung

Rielta

Rielta Ladoga MK-RK Bedienungsanleitung

Mirion Technologies

Mirion Technologies ACCURAD PRD Bedienungsanleitung

Bosch

Bosch DS835 Bedienungsanleitung

DBI SALA

DBI SALA EZ Stop Bedienerhandbuch

Lamptime

Lamptime ST05C Bedienungsanleitung

Ubiquiti

Ubiquiti MFI-MSC Bedienungsanleitung

Subsite

Subsite 910R Montageanleitung

Satel

Satel OPAL Pro Bedienungsanleitung

Aleph

Aleph XC-1XTEU Bedienungsanleitung

Pima

Pima LARIS QUAD Bedienungsanleitung