Zephyr ALA-M90BBX Produkthandbuch

www.zephyronline.com

Duo Wall

ADU-M90BSX

Layers Wall

ALA-M90BBX

ALA-M90BWX

ALA-E42BBX

ALA-E42BWX

RANGE HOOD - Installation and use instructions

ENGLISH........................................2

FRANÇAIS...................................30

- 15 -

INSTALLING THE DUCTWORK:

INTERNAL BLOWER

NOTE: To reduce the risk of fire, use only

metal ductwork.

1. Decide where the ductwork will run

between the hood and the outside.

2. A straight, short duct run using a minimum

6” round duct will allow the hood to perform

most efficiently.

3. Long duct runs, elbows, and transitions will

reduce the performance of the hood. Use

as few of them as possible.

4. Install a roof or wall cap. Connect round

metal ductwork to cap and work back

towardshoodlocation.Useducttapetoseal

the joints between ductwork sections

(Fig.7). FIG. 7

ROOF CAP

DUCT COVER

HOOD

24” MINIMUM

ABOVE COOKING

SURFACE

WALL

CAP

6” ROUND DUCT

INSTALLING THE INTERNAL

BLOWER

NOTE: The following instructions are for

installingtheinternalblower only.

Installthisrangehoodonlywithinternalblower

model CBI-290A or CBI-600A.

1. Remove the electrical system box from

chimney frame by removing duct tape.

2. Remove the 6” metallic flange provided on

the blower’s air outlet (the flange may

already be pre-installed) (Fig.8).

3. Remove the front plate from the metal

blower housing by unscrewing (4) 3.9x9.5

mm screws (Fig.9).

4. Attach electrical system box to front plate

using (2) 3.9 x 9.5 mm screws from

FIG. 8

FIG. 9

FIG. 10

(2) MOUNTING

SCREWS

3.9 x 9.5 mm

ELECTRICAL

SYSTEM BOX

METAL

BLOWER

HOUSING

- 16 -

FIG. 11

FIG. 13

FIG. 12

(4) MOUNTING SCREWS

(Supplied with the motor)

(4) MOUNTING SCREWS

(3.9 x 6 mm Flat Head)

hardware bag (Fig.10).

5. Remove the blower plate unscrewing the

(4) 3.9x9.5 mm screws (Fig.11).

6. Install internal blower into blower plate and

secure using (4) screws (supplied with the

internal blower) - See Fig.12.

7. Install blower using (4) 3,9 x 6mm mounting

screws (Fig.13).

- 17 -

FIG.14

INTERNAL BLOWER WIRING

Note: This range hood must be properly grounded. The unit should be installed by a

qualified electrician in accordance with all applicable national and local electrical codes.

1. Make connections (A, B,C) (Fig.14).

2. Secure capacitor box screwing the (2) 3.9x9.5 mm screws (Fig.14D).

3. Remove the wiring box cover. Remove a knockout from the wiring box (Fig.14A).

4. Secure the conduit to the wiring box through a conduit connector.

5. Make electrical connections. Connect white to white, black to black and green to ground.

6. Replace wiring box cover and screws. Make sure that wires are not pinched between cover

and box.

WIRING BOX

COVER

GROUND

CONNECT:

WHITE-TO-WHITE,

BLACK-TO-BLACK,

GREEN-TO-GROUND.

- 18 -

8. Install the front plate and electrical system

box using (4) 3.9x6 mm screws (Fig.15).

FIG. 15

FIG. 16

9. Place the 6” metallic flange provided on the

blower’s air outlet (Fig.16).

(4) MOUNTING SCREWS

(3.9 x 6 mm Flat Head)

- 19 -

REMOTE BLOWERS (EXTERNAL AND IN-LINE)

CAUTION: To reduce risk of fire and electric shock, install this range hood only with External

Blower Model CBE-1000, and In-Line Blower Model PBN-1000A. Other blowers cannot be

substituited.

INSTALLING THE DUCTWORK: REMOTE BLOWER

NOTE: To reduce the risk of fire, use only metal ductwork.

1. Choose the location where the External Blower or In-Line Blower will be mounted. See

illustrations below for mounting location suggestions and restrictions.

2. A straight, short duct run using a minimum 8” round duct will allow the hood to perform

most efficiently.

3. Long duct runs, elbows and transitions will reduce the performance of the hood. Use as

few of them as possible. Larger ducting may be required for best performance with long

duct runs.

4. After the External or In-Line Blower has been installed, connect round metal ductwork

and work back towards the hood location. Use duct tape to seal joints between ductwork

sections.

Roof Pitch w/

Flashing & Cap

in-line

blower

(blower

housing) (blower

housing)

external blower

Attic or crawl space

- 20 -

INSTALLING THE REMOTE

BLOWER

NOTE: The following instructions are for

preparing the hood for use with external or

in-line blower models CBE-1000 or PBN-

1000A. For blower installation details refer

to manual included with the blower.

1. Remove the electrical system box from

chimney frame by removing duct tape.

2. Remove side screw (Fig.17) and mount

electricalsystem boxby means(2) 3,9x9,5

mm screws; re-fix the side screw.

3. Remove the blower plate unscrewing the

(4) 3.9x6 mm screws (Fig.18).

4. Remove (2) screws (Fig.19A), position the

external blower plate and remote blower

box over blower housing and fix using (4)

3.9x6 mm screws (Fig.19B).

5. Install 8” round blower collar to top of

blower housing screwing the (4) 3.9x6 mm

screws (Fig.20)

FIG. 18

FIG. 19 FIG. 20

FIG. 17

(4)

MOUNTING

SCREWS

(3.9x6mm

Flat Head)

(4)

MOUNTING

SCREWS

(3.9 x 6 mm

Flat Head)

ELECTRICAL

SYSTEM BOX

(2) SCREWS

3.9 x 9.5 mm

SIDE SCREW

- 21 -

REMOTE

BLOWER

BOX

FIG.21

REMOTE BLOWER WIRING

1. Remove the cover from the wiring box marked “120 Vac input”.

2. Remove one knockout from the (2) wiring boxes (box marked “120 Vac input” and box

marked “motor connection”).

3. Run 4-wire plus ground power cable from the remote blower to the remote blower wiring

box marked “motor connection” (Fig.21B).

4. Feed6” of cablethrough the knockoutopening and securethe cable tothe wiring boxwith

an appropriate connector.

5. Make electrical connections at the hood (box marked 120 Vac input). Connect white-to-

white, black-to-black, green-to-ground (Fig.21A).

6. Make electrical connections (remote blower box marked “motor connection”). Connect

white-to-white, black-to-black, blue-to-blue, red-to-red, green-to-ground (Fig.21B).

7. Mount the wiring box covers and screws. Make sure wires are not pinched between the

cover and box.

External blower connection:

1. Make electrical connections at the remote blower (see instructions provided with the

remote blower).

REMOTE BLOWERHOOD WIRE

HARNESS

WHITE(COMMON)

BLACK(HIGH)

BLUE(MED)

RED(LOW)

GREEN(GROUND)

(2)

MOUNTING

SCREWS

3.9 x 9,5 mm

BOX MARKED

“120 VAC INPUT”

ACONNECT:

WHITE-TO-WHITE,

BLACK-TO-BLACK,

BLUE-TO-BLUE

RED-TO-RED

GREEN-TO-GROUND.

GROUND

CONNECT:

WHITE-TO-WHITE,

BLACK-TO-BLACK,

GREEN-TO-GROUND.

- 22 -

INSTALL THE HOOD

Remove the plastic protective film from all

exteriorsurfaces,ductcoversandfilters,prior

tofinalinstallation

1. Construct wood wall framing that is flush with

interior surface of wall studs (Fig.22/23).

Make sure:

a) the framing is centered over installation

location.

b) the height of the framing will allow the hood to

be secured to the framing within the

dimensions shown.

2. Determine desired height over cook top

and mark hood bottom line. Install drywall

anchors and 4,8x38mm screws per

dimensions shown in Fig. 22/23.

3. Hang the hood onto the screws.

4. Tighten mounting screws. Add additional

screws through hood body as needed for

additional support.

Notes:

a. Minimum hood distance above cook top

must not be less than 24”. A maximum of

36” above cook top is highly

recommended for best capture of cooking

impurities. Distances over 36” are at the

installer and the users discretion; and if

ceiling height and flue lenght permit.

FRAMING BEHIND WOOD

CROSS SUPPORT

WOOD CROSS

SUPPORT BEHIND

DRYWALL DRYWALL

8-1/4”

16-7/16” FROM

BOTTOM OF HOOD

HOOD

BOTTOM

FIG.22

FRAMING BEHIND WOOD

CROSS SUPPORT

WOOD CROSS

SUPPORT BEHIND

DRYWALL DRYWALL

FIG.23

Model Layers

8-1/4”

15-11/16” FROM

BOTTOM OF HOOD

HOOD

BOTTOM

Model Duo

- 23 -

MOUNTING SCREWS

(4.8 x 38mm)

(2) MOUNTING SCREWS

(3.9 x 6 mm Flat Head)

INSTALL DUCT COVER

MOUNTING BRACKET

DUCTED AND NON-DUCTED

1.Assembletheductcovermountingbracket,

adjusting outside width as shown. (Fig.24)

2.Carefully center the mounting bracket

directly over the range hood location.

3.Secure the bracket assembly to the ceiling

using(2)4.8x38mmmountingscrewsand

drywall anchors (Fig.25). Make sure the

bracket is pushed into the corner, tight

againstthewallifnecessary, andcentered

over the hood.

DRYWALL

ANCHORS

FIG.24

FIG.25

3/4

”

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Zephyr Dunstabzugshaube Handbücher

Zephyr

Zephyr Verona Island ZVN-M90AG Installationsanleitung

Zephyr

Zephyr ATI-M90ASX Bedienungsanleitung

Zephyr

Zephyr Pisa ZPI-E24AG290 Installationsanleitung

Zephyr

Zephyr Twister Installationsanleitung

Zephyr

Zephyr ZTR-M90S Installationsanleitung

Zephyr

Zephyr ZNA-M90BS Installationsanleitung

Zephyr

Zephyr SAVONA ZSA-M90AS Installationsanleitung

Zephyr

Zephyr Venezia ZVE-E30AS Bedienungsanleitung

Zephyr

Zephyr Genova Series Bedienungsanleitung

Zephyr

Zephyr Venezia Installationsanleitung

Zephyr

Zephyr ZMO-E30BS Installationsanleitung

Zephyr

Zephyr Willow AK8800AS Installationsanleitung

Zephyr

Zephyr Breeze II AK1200x Installationsanleitung

Zephyr

Zephyr ZRG-E30AS Installationsanleitung

Zephyr

Zephyr Monsoon I Installationsanleitung

Zephyr

Zephyr Optica Island EOT-E42ASX Installationsanleitung

Zephyr

Zephyr Verona Island ZVN-M90AG Installationsanleitung

Zephyr

Zephyr ZSL-E48BS Installationsanleitung

Zephyr

Zephyr Roma Groove Installationsanleitung

Zephyr

Zephyr Typhoon AK2100BS Installationsanleitung

Zephyr

Zephyr Typhoon AK2100CS Installationsanleitung

Zephyr

Zephyr Z1C-00SU Bedienungsanleitung

Zephyr

Zephyr Lux ALU-E43CSX Installationsanleitung

Zephyr

Zephyr AK9440AS Installationsanleitung

Beliebte Dunstabzugshaube Handbücher anderer Marken

emmeti

emmeti RECUPA MED A-140 Leitfaden

Nibe

Nibe F135 Bedienungsanleitung

Kuppersberg

Kuppersberg INTRO 60 Montage- und Wartungsanleitung

Hisense

Hisense MH6INBG Bedienungsanleitung

Miele

Miele DA 1255 Bedienungsanleitung

Broan

Broan 46000 Bedienungsanleitung

GE Profile PV977 Originalbetriebsanleitung

FALMEC

FALMEC FFRIA24W5FS Bedienungsanleitung

Whirlpool

Whirlpool RH2600XL-1 SERIES Bedienungsanleitung

Küppersbusch

Küppersbusch DX ISLA Bedienungsanleitung

ETNA

ETNA AV360RVS Bedienungsanleitung

JUNO

JUNO JDF603E6 Bedienungsanleitung

Miele

Miele DA 6708 D Bedienungsanleitung

Tricity Bendix

Tricity Bendix LE 150 Handbuch

AEG

AEG X68163BV1 Bedienungsanleitung

AEG

AEG 125 D Bedienungsanleitung

Smeg

Smeg KSEV97X Bedienungsanleitung

Nibe

Nibe S Series Benutzerhandbuch