Zip HydroTap G4 Konfigurationshandbuch
801525 v3.05 09.20 HT C Com Install Instructions Page 1 of 16
Affix Model Number Label
Here
801525
Chilled Commercial
Zip HydroTap G4
Installation and Operating Instructions
®
Page 2 of 16 801525 v3.05 09.20 HT C Com Install Instructions
Tap options
The Zip HydroTap G4 appliance series offers a range of interchangeable taps to suit the customer’s needs
These three taps are directly compatible with the G4
Command Centre.
Arc / Cube Tap
Classic Tap
Elite Tap
801525 v3.05 09.20 HT C Com Install Instructions Page 3 of 16
HydroTap Specifications
Installation Checklist .................................................................................................................... 4
General Product Features............................................................................................................ 5
Important Safety Instructions ....................................................................................................... 6
Warnings and Regulatory Information.......................................................................................... 7
Major Components and Accessories ........................................................................................... 8
Technical Specification ................................................................................................................ 8
Before Installation and Site Requirements................................................................................... 9
Installation Instructions
STEP 1 -
Measure and cut all the tap holes before fitting the taps
(Refer to the Tap installation instruction book 803341)
STEP 2
- Check for adequate ventilation
Section 2 - Ventilation
2.1 - Details....................................................................................................................... 10-11
STEP 3
- Install the Command Centre
Section 3 - Command Centre Installation
3.1 - Fit the mains water supply hose ............................................................................... 12
3.2 - Model C 125 and C 175............................................................................................ 12
STEP 4
- Commission the HydroTap
Section 4 - Commissioning
4.1 - Language.................................................................................................................. 13
4.2 - Filter flush ................................................................................................................. 13
4.3 - Command Centre Flush............................................................................................ 14
Troubleshooting ........................................................................................................................... 15
End of Life Disposal ..................................................................................................................... 15
Contact Details............................................................................................................................. 16
Index
Page 4 of 16 801525 v3.05 09.20 HT C Com Install Instructions
Before Installation:
A. Read the instructions and check if there is adequate space to mount all of the components.
B. Note: Not all fittings are supplied with the appliance kit. Isolation valves are not supplied.
C. Check the mains water pressure is between 150 - 700kPa
D. Check the water quality to determine if extra filtration will be required.
E. Check the appliance rating plate and ensure correct power is available for the appliance.
F. Check the under counter cupboard supporting the appliance is adequate for
the total weight of the appliance, when full of water.
Before Commissioning:
1. Check the unit has been installed correctly.
2. Check all plumbing fittings have been tightened.
3. Ensure the outlet pipe is positioned to drain correctly.
4. Ensure there is adequate ventilation.
5. Check all tubes from the Command Centre to the tap, have a constant rise and there are no
sags or kinks in the hoses.
6. Check all electrical connections are correct and there are no loose wires.
Commission: (See section 4)
7. Flush the supply line before connecting.
8. Connect and turn on the water to check for leaks.
9. Flush the filter.
10. Where applicable, programme the unit to suit the customer’s requirements.
Installation checklist
801525 v3.05 09.20 HT C Com Install Instructions Page 5 of 16
Thank you for purchasing a Zip Chilled HydroTap. Please read and follow these instructions carefully to ensure
safe operation and trouble free service. If service is required, please call your Zip Service Provider.
What is the Zip HydroTap ?
The Chilled Zip HydroTaps are electronically controlled to supply filtered and Chilled drinking water for
kitchens and tea rooms. The Chilled HydroTap units are under bench drinking water appliances with a
dispensing tap mounted on a sink or bench, which may be used for commercial applications. These units
utilise a conventional refrigerant compressor to chill the water which is factory set to 5-9°C. These units are
NOT designed to be used for sanitary fixtures.
The water filter is a disposable item which will require periodic replacement and is covered by a limited OEM
warranty.
It is important that the Installation be done safely, correctly and completely, in order to utilise all the benefits
the HydroTap can provide. Each unit can be ordered with the Tap Head Assembly for disabled use. The
disabled levers are supplied with Braille caps for the visually impaired.
General Product Features
HydroTap C125
HydroTap C175
Page 6 of 16 801525 v3.05 09.20 HT C Com Install Instructions
Important Safety Instructions
This manual contains important safety and installation instructions for the Zip HydroTap G4.
Safety
This appliance is not intended for use by persons (including children) with reduced physical,
sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision
or instruction concerning use of the appliance by a person responsible for their safety. Children should be
supervised to ensure that they do not play with the appliance.
For products sold in Europe, this appliance can be used by children aged from 8 years and above and
persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they
have been given supervision or instruction concerning use of the appliance in a safe way and understand
the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be
made by children without supervision.
Qualifications
If the power cable is damaged it must be repaired only by a qualified technician. To avoid hazards, all
installation procedures must be carried out by a suitably qualified tradesperson. The power cable and power
outlet must be in a safe visible position for connection.
Lifting
Take care when lifting the Zip HydroTap unit. Some units may exceed safe lifting limits. If you feel this is
beyond your personal capabilities, please seek assistance with the lift. The weights of the units are marked
on the packaging. Do not lift the unit by the front cover or any connections at the top rear of the unit. Refer to
page 7 for the weight of your product.
Airflow
The ambient temperatures this unit should operate within are 5ºC - 35ºC. Proper air circulation must be
provided. The system will operate satisfactorily only if the recommended air gaps are provided. If a vent kit is
supplied it must be fitted. See technical specifications for correct installation to prevent overheating.
Positioning
It is important to ensure the Command Centre is positioned in an accessible area close to the floor level. The
unit must have its base mounted in a horizontal position with all inlets and outlets facing up. The Tap must be
located above the Command Centre.
!
801525 v3.05 09.20 HT C Com Install Instructions Page 7 of 16
WARNINGS
1. The Zip HydroTap unit must be earthed. The resistance of the earth connection
from each exposed metal part must be less than 1 ohm.
2. All Installation and service work must be completed by trained and suitably
qualified Tradespeople. Faulty operation due to unqualified persons working on
this product, or any other Zip product may void warranty coverage.
3. Plumbing and electrical connections must be made in accordance with local
regulations and relevant standards. In Australia and New Zealand: Plumbing
standard AS/NZS 3500 & Electrical Wiring Rules AS/NZS 3000.
4. This HydroTap product is rated for 230V 50Hz AC operation.
5. This unit must be installed with adequate clearances of 50mm on all sides, and
200mm above, to allow for air circulation. Additional means of ventilation is
critical if the vent kit, as supplied, cannot be fitted.
6. Flush water supply lines before any plumbing connections are made, to prevent
sediment from affecting operation.
7. The Command Centre must not be located near, or cleaned with water jets.
8. This product is designed for indoor use and must not be installed outdoors or
exposed to the elements of nature.
9. For safe operation, the HydroTap is designed to be installed, commissioned and
used within 48 hours. Should the HydroTap not be required for an extended
period of time (72 hours or more), do not fill and commission the HydroTap until
ready for first use.
10. For water taste and quality reasons, following any non-use period of more
than 72 hours, Zip recommends to perform a system flush. Failure to flush the
system may affect water quality.
11. Due to the process of continuous improvement, Zip Water reserves the right to
change details mentioned in this manual, without notice.
WARNINGS
!
Page 8 of 16 801525 v3.05 09.20 HT C Com Install Instructions
Technical Specifications
Commercial Models:
C = Chilled filtered
D = Disabled lever controls, (Order as an option)
Model
Glasses of
Chilled Water
per Hour
C 175
Note: the standard Glass measurement =200ml
** Add an extra 3 kg when full of water
Capacity
Chilled
(glasses)
Boost
(10A)
GPOs
Required
Power
Rating
(kW)
Unit Dimensions
W x D x H (mm)
with air duct
**Dry
Weight
(Kg)
Tank Material
Chilled Only
C125 125 no 1x10A 0.175 336 x 476 x 335 20 Stainless
C175 175 no 1x10A 0.300 336 x 476 x 335 20 Stainless
Major Components and Accessories
Parts supplied Description
HydroTap
with hoses
(Classic tap shown)
1 off
HydroTap
Command Centre with
water filter
1 off
Mains water
connection hose
Vent Kit
1 x Inlet vent
1 x Outlet vent
9 x Screws
1 x Air Duct
1 x Mounting plate
1 x Installation
Instructions (this book)
1 x User guide
Accessories Description
Font Kit for
Arc & Cube Models
Font Kit for Classic &
Elite Models
Replacement Filter
Disabled Lever Kit
User
Guide
Install
Instruct
801525 v3.05 09.20 HT C Com Install Instructions Page 9 of 16
Before installing ensure that the following have been provided at the installation
site:
•
Review all the technical specifications.
•
Ensure the underbench can support the product weight when full of water,
(allow an extra 3 kg when full. )
•
Sufficient space in the cupboard to install all of the Command Centres in accordance with these
Installation Instructions. Refer to technical specification for dimensions. Refer to section 3 & 4, for
Installation instructions.
•
The chilled HydroTap models require a 220-240 V AC, 10A GPO
NOTE: Check all cable and hose lengths against inlet /outlet positions before
proceeding (See section 5 for general layout).
•
A potable water supply connection with isolating valve inside the cupboard within reach of the braided
hoses and positioned so that the connection point and the stop cock will not be obstructed when the
Command Centres are installed.
•
A cold water supply with a minimum working pressure of 150kPa and a maximum working pressure of
700kPa connected via an isolation valve.
•
The appliance must be placed with its base in a horizontal position.
IMPORTANT!
Do not proceed with the Installation if these requirements are not met.
Before Installation and Site Requirements
Special Tools Required:
In addition to normal tools, the following will be required:
For the standard taps:
•
35mm diameter sheet metal hole punch for sink tops. (Not supplied)
•
35mm diameter hole saw for timber bench tops. (Not supplied)
•
Nut runner tube spanner (supplied) for fixing tap assembly.
•
Jig saw for ventilation cut outs
When installing a font kit, the following will be required:
•
140mm diameter sheet metal or hole saw to suit surface being cut.
Section 1
Tap Installation
Refer to the Tap installation instruction book 803341.
!
Page 10 of 16 801525 v3.05 09.20 HT C Com Install Instructions
Section 2
Ventilation
2.1 All Models
IMPORTANT: Proper air circulation must be provided. Allow a clearance envelope of 50mm either
side, and 200mm above the Command Centre. The system will operate correctly only if the recom-
mended clearances are provided.
It is recommended to install vent duct and louvre panels for under floor and /or door vent systems.
**Note: Inlet and outlet vents should be separated by a minimum of 100mm, to avoid hot air recirculation.
When installing air flow ducts, the following tools will be required:
•
Jigsaw and 12mm drill.
•
Keyhole or Wall Board saw.
Recommended Installation showing the correct air flow
**MIN. 100mm
Warm Air OUT
via kickboard louvre
MIN. 50mm
Cool Air IN via
cabinet floor,
front vent grille
!
Andere Handbücher für HydroTap G4
23
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere Zip Wassersystem Handbücher
Zip
Zip HydroTap G4 Bedienungsanleitung
Zip
Zip Chilltap CH103 Bedienungsanleitung
Zip
Zip HydroTap G4 Bedienungsanleitung
Zip
Zip HydroTap G4 Bedienungsanleitung
Zip
Zip HydroTap G5 Touch-Free Wave Bedienungsanleitung
Zip
Zip HydroTap G4 Bedienungsanleitung
Zip
Zip HydroTap G4 Bedienungsanleitung
Zip
Zip HydroTap G5 Touch-Free Wave Bedienungsanleitung
Zip
Zip HydroTap G4 Bedienungsanleitung
Zip
Zip HydroTap G4 802701 Bedienungsanleitung
Zip
Zip HydroTap G4 Bedienungsanleitung
Zip
Zip HydroTap CS Commercial Bedienungsanleitung
Zip
Zip Elite HydroTap G4 range Bedienungsanleitung
Zip
Zip HydroTap G5 BCS Bedienungsanleitung
Zip
Zip HydroTap G4 Bedienungsanleitung
Zip
Zip Chilltap CH103 Bedienungsanleitung
Zip
Zip HydroTap BCS Series Bedienungsanleitung
Zip
Zip HydroTap G4 Celsius Series Bedienungsanleitung
Zip
Zip HydroTap G4 Bedienungsanleitung
Zip
Zip HydroTap G4 IS Industrial Series Bedienungsanleitung
Beliebte Wassersystem Handbücher anderer Marken
Spirotech
Spirotech SPIROVENT SUPERIOR S250 Bedienungsanleitung
Culligan
Culligan Aqua-Cleer Aqua-Cleer Advanced Drinking Water... Bedienungsanleitung
A.O. Smith
A.O. Smith Dura-Max AJH - 1000A - P Bedienungsanleitung
Microline
Microline T.F.C.-4 Handbuch
Eureka Forbes
Eureka Forbes Aquaguard Select Bedienungsanleitung
Cetetherm
Cetetherm AquaEfficiency Bedienungsanleitung
