ZKTeco ProBio Bedienungsanleitung

ProBio(QR)

Version: 1.0

Date: May 2021

QUICK START GUIDE

Safety Precautions

Before installation, please read the following precautions carefully

risks and dangers to this product, users and surroundings.

to prevent

Do not expose to direct sunlight, water, dust and soot.

Do not place magnetic object near the product. Magnetic objects

such as Magnet, , , Monitor or Speaker may damage the device.

any

CRT TV

Do not place the device next to any heating equipment.

Prevent water, drinks or chemicals leaking into the device.

This product is not intended for use by children unless they are supervised.

Do not drop or damage the device.

Do not disassemble, repair or modify the device.

Do not use the device for any purpose other than those specified.

Remove dusts or dirts regularly. While cleaning, wipe dust off with a

smooth cloth or towel instead of water.

Contact your supplier in case of any problem!

User Registration

1.15m

0.5m

1.15m

0.5m

1.15m

0.5m

For user heights between 1.5m to 1.8m, it is recommended

to install the device at 1.15m height above ground (can be

modiﬁed according to the user’s average height).

2) Registration

a. During registration, it is required to adjust your upper body to ﬁt your eyes into the green

frame on the screen.

b. During veriﬁcation, it is required to show your face in the center of the screen and ﬁt your face

into the green frame in the screen.

1) Recommended Standing Position

Recommended Procedures (as shown in

the left image): During registration and

veriﬁcation procedures, the position of device

should not be changed to

veriﬁcation preciseness. If it is necessary to

move the device, its vertical height should

not be changed.

ensure high

Device Overview

2.8" Touch Screen

Doorbell

Camera

Card Reading Area

& QR Code Scanner

USB Port

Reset Button

Tamper Switch

Terminal Block

Speaker

85mm (3.35")

190.8mm (7.51")

103mm (4.05")

Device Installation

Installation on the wall

1.15m

FixingHole

Mounting PositioningSticker

(only for your reference)

Instructionon using Mounting Positioning Sticker:

WiringHole

FixingHole FixingHole

1.15mrecommended height from the ground

forfacial terminal and 1.4m for ﬁnger vein

terminal,it can be adjusted according to

thestaﬀ height.

Beforefastening the device, please stick this

MountingPositioning Sticker onto where you want to

installthe device, and then drill holes and lay cables

accordingto the symbols on the sticker.

MPS201508

①

②

③

④

Attach the mounting template sticker to the wall, and drill holes according to the mounting

paper.

Fix the back plate on the wall using the wall mounting screws.

Attach the device to the back plate.

Fasten the device to the back plate with a security screw.

Baseline 129 mm (5.08")

61mm (2.4")

Power Connection

Without UPS

With (Optional)UPS

GND

12V DC

GND

12V DC

PowerIn

Lock

Alarm

Button

Sensor

Bell

Out

Ethernet

Power

Out

RedLED

Beep

Green

GND

WD1

WD0

GND

+12V

GND

Wiegand

485B

485A

RJ45-1

RJ45-2

RJ45-3

RJ45-6

IWD1

IWD0

RS485

Wiegand

+12V

BELL-

BELL+

SEN

AUX

GND

BUT

N1O

COM1

N1C

AL-

AL+

{

RLED

BEEP

GLED

TXD

RXD

GND

RS232

Auxiliary

LED

PowerIn

Lock

Alarm

Button

Sensor

Bell

Out

Ethernet

Power

Out

RedLED

Beep

Green

GND

WD1

WD0

GND

+12V

GND

Wiegand

485B

485A

RJ45-1

RJ45-2

RJ45-3

RJ45-6

IWD1

IWD0

RS485

Wiegand

+12V

BELL-

BELL+

SEN

AUX

GND

BUT

N1O

COM1

N1C

AL-

AL+

{

RLED

BEEP

GLED

TXD

RXD

GND

RS232

Auxiliary

LED

12V DC

Recommended AC Adapter

Recommended AC Adapter 12V A3:,

To share the power with other devices, use an with higher current ratings.AC Adapter

Ethernet Connection

RJ 45

LAN Connection

RJ45-1 Yellow

RJ45-2

Red

RJ45-3

RJ45-6 Black

Green

WIRE

DESCRIPTION

ZKBioSecurity

PowerIn

Lock

Alarm

Button

Sensor

Bell

Out

Ethernet

Power

Out

RedLED

Beep

Green

GND

WD1

WD0

GND

+12V

GND

Wiegand

485B

485A

RJ45-1

RJ45-2

RJ45-3

RJ45-6

IWD1

IWD0

RS485

Wiegand

+12V

BELL-

BELL+

SEN

AUX

GND

BUT

N1O

COM1

N1C

AL-

AL+

{

RLED

BEEP

GLED

TXD

RXD

GND

RS232

Auxiliary

LED

Connect the device and the software over an Ethernet cable. An example is shown below:

: 192.168.1.201Default IP Address

Subnet Mask: 255.255.255.0

: 192.168.1.61

: 255.255.255.0

IP Address

Subnet Mask

Click , enter the IP address and click .[Comm.] > [Ethernet] > [IP Address] [OK]

Note:

In LAN, the IP Addresses of the Server (PC) and the device must be in the same network

segment when connecting to the ZKBioSecurity software.

RS485 Connection

Rs485 Slave Reader

Do not use

BEEP Purple

GLED Gray

IWD1 Green

RLED Blue

+2V1Red

GND Black

IWD0 White

DESCRIPTION WIRE

485B Yellow

485A Blue

GND Black

TXD Purple

GND Black

WD0 Green

WD1 White

RXD Gray

DESCRIPTION WIRE

PowerIn

Lock

Alarm

Button

Sensor

Bell

Out

Ethernet

Power

Out

RedLED

Beep

Green

GND

WD1

WD0

GND

+12V

GND

Wiegand

485B

485A

RJ45-1

RJ45-2

RJ45-3

RJ45-6

IWD1

IWD0

RS485

Wiegand

+12V

BELL-

BELL+

SEN

AUX

GND

BUT

N1O

COM1

N1C

AL-

AL+

{

RLED

BEEP

GLED

TXD

RXD

GND

Rs232

Auxiliary

LED

Rs485 Slave Reader Connection

DIP Settings

123456

1. There are six DIP switches on the back of RS485 slave reader, switches 1 to 4 are for RS485

address, switch 5 is reserved, and switch 6 is for reducing noise on a long RS485 cable.

2. If the RS485 slave reader is powered from the terminal, the length of wire should be less

than 100 meters or 330 ft.

3. If the cable length is more than 200 meters or 600 ft., the number 6 switch should be

turned ON as shown below.

Distance: More than 200 metersDistance: 200 metersLess

Lock Relay Connection

Device Not Sharing Power with the Lock

Normally Closed Lock

GND

Sensor

12V DC

COM1

12V DC

GND GND

AUX

GND

BELL-

Yellow

BELL+

SEN

GND Red

BUT

NO1 White

COM1 Black

NC1 Gray

Black

AL+ Red

Brown

Purple

Green

Orange

Blue

DESCRIPTION WIRE

Do not use

PowerIn

Lock

Alarm

Button

Sensor

Bell

Out

Ethernet

Power

Out

RedLED

Beep

Green

GND

WD1

WD0

GND

+12V

GND

Wiegand

485B

485A

RJ45-1

RJ45-2

RJ45-3

RJ45-6

IWD1

IWD0

RS485

Wiegand

+12V

BELL-

BELL+

SEN

AUX

GND

BUT

N1O

COM1

N1C

AL-

AL+

{

RLED

BEEP

GLED

TXD

RXD

GND

RS232

Auxiliary

LED

GND

FR107

Diode

NC1

Do not reverse the polarities.

The system supports both and . The

(Normally Opened when powered) is connected with ' ' and ' ' terminals, and the

(Normally Closed when powered) is connected with ' ' and ' ' terminals. The power can be

shared with the lock or can be used separately for the lock, as shown in the example with NC

Lock below:

Normally Opened Lock Normally Closed Lock NO Lock

NO COM NC Lock

NC COM

AL-

Lock Relay Connection

Device Sharing Power with the Lock

AUX

GND

BELL-

Yellow

BELL+

SEN

GND Red

BUT

NO1 White

COM1 Black

NC1 Gray

Black

AL+

AL-

Red

Brown

Purple

Green

Orange

Blue

DESCRIPTION WIRE

Do not use

PowerIn

Lock

Alarm

Button

Sensor

Bell

Out

Ethernet

Power

Out

RedLED

Beep

Green

GND

WD1

WD0

GND

+12V

GND

Wiegand

485B

485A

RJ45-1

RJ45-2

RJ45-3

RJ45-6

IWD1

IWD0

RS485

Wiegand

+12V

BELL-

BELL+

SEN

AUX

GND

BUT

N1O

COM1

N1C

AL-

AL+

{

RLED

BEEP

GLED

TXD

RXD

GND

RS232

Auxiliary

LED

BEEP Purple

GLED Gray

IWD1 Green

RLED Blue

+2V1Red

GND Black

IWD0 White

DESCRIPTION WIRE

COM1

FR107

Diode

GND

12V DC

Sensor

GND

NC1

Normally Closed Lock

!Do not reverse the polarities.

Andere Handbücher für ProBio

Inhaltsverzeichnis

Andere ZKTeco Sicherheitssystem Handbücher

ZKTeco

ZKTeco FR1200 Bedienungsanleitung

ZKTeco

ZKTeco FMD Pro 2.0 Bedienungsanleitung

ZKTeco

ZKTeco FaceDepot-7BL Bedienungsanleitung

ZKTeco

ZKTeco ZKX6550 Bedienungsanleitung

ZKTeco

ZKTeco G4 Pro Series Bedienungsanleitung

ZKTeco

ZKTeco ZKRF10M Bedienungsanleitung

ZKTeco

ZKTeco SF1008+ Bedienungsanleitung

ZKTeco

ZKTeco X7 Bedienungsanleitung

ZKTeco

ZKTeco ProFace X Bedienungsanleitung

ZKTeco

ZKTeco FaceKiosk-H13 Bedienungsanleitung

ZKTeco

ZKTeco SpeedFace Series Bedienungsanleitung

ZKTeco

ZKTeco OP-400 Bedienungsanleitung

ZKTeco

ZKTeco RF100 Bedienungsanleitung

ZKTeco

ZKTeco DM10 Bedienungsanleitung

Beliebte Sicherheitssystem Handbücher anderer Marken

Inner Range

Inner Range Concept 2000 Bedienungsanleitung

Climax

Climax Mobile Lite R32 Montageanleitung

CADDX

CADDX NX-6 Bedienungsanleitung

FBII

FBII XL-31 Series Bedienungsanleitung

Johnson Controls

Johnson Controls PENN Connected PC10 Bedienungsanleitung

Aeotec

Aeotec Siren Gen5 Bedienungsanleitung

Blaupunkt

Blaupunkt SA 2700 Bedienungsanleitung

IDEAL

IDEAL Accenta Betriebsanleitung

AJAX

AJAX DoubleButton Bedienungsanleitung

Swann

Swann SW-P-MC2 Bedienungsanleitung

Ecolink

Ecolink Siren+Chime Bedienungsanleitung

Digital Monitoring Products

Digital Monitoring Products XR150 Bedienungsanleitung

EDM

EDM Solution 6+6 Wireless-AE Bedienungsanleitung

Highway Safety Group

Highway Safety Group EA401 Bedienungsanleitung

Siren

Siren LED GSM Bedienungsanleitung

Detection Systems

Detection Systems 7090i Montageanleitung

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Bedienungsanleitung

Siemens

Siemens FDM273 Bedienungsanleitung