ZKTeco Mars-S1000 Bedienungsanleitung

Installation Guide

Mars-S1000/Mars Pro-S1000

Version: 1.0

Due to regular upgrades of systems and products, ZKTeco could not guarantee exact consistency between the

actual product and the written information in this manual.

It is recommended that the swing barrier turnstile must be installed on a horizontal solid platform

with a height of 50mm to 100mm.

After installation, check if the connection is done correctly at the connecting points of the ground

wire, at the connector assemblies and wiring points of the circuits, as well as at each movable part

of the swing barrier turnstile. Any loose nuts, screws and other fasteners should be tightened in

time to avoid any failures caused by long-time operations.

1 Installation Requirements

3. Make sure the ground wire of the system is reliably connected to avoid personal injuries or other

accidents.

2. It is also recommended that the swing barrier turnstile should not be used in the corrosive

environment.

The installation position of the swing barrier turnstile depends on its size. A distance of 100mm between

the swing barrier turnstile and the wall needs to be reserved for ease of opening the top cover of the

machine to perform maintenance and adjustment. The reference ﬁgure is shown below:

2 Installation Position

1947

1022

245

875

650

50 50

650

100 100

120.00

120.00 120.00

1355.00

1023.05

3 Preparation

To install the Mars-S1000/Mars Pro-S1000 you must have:

A Screwdriver: To remove or install the screw on the device.

A Pencil: To mark the device size and the screw hole.

A Electric Drill: Drill holes according to the marked screw holes.

A Wrench: Secure the M12 expansion screw on the device.

4 Installation

1. Place the turnstile to the installation site.

4 Installation

Remove the screws ﬁxing the top lid, and remove the top lid.

②

①

Remove the side lid that hang on the device.

Mark the ﬂoor following the periphery of the legs.

853.00 60.00

1282

1182

913

60.00

650

Take the turnstile aside and use the electric drill according to the drawn screw holes.

6. Clean up the soil and dust after the drilling is completed, place the turnstile to the installation site

again.

Insert the M12 expansion screw and tighten it with a wrench.

8. Connect the online cables and perform the power-on test. If the test is OK, install the side lid and

top lid of the device.

9. It is recommended that a warning line be marked on the ground after installing the device, so as to

prompt the pedestrian to stand behind the warning line when veriﬁcation.

1033

650

1022

245

875

100.00

120.00 120.00

M12Expansion

Screw

Tether Cable

Power Line

Ethernet

φ25mm PVC pipe

10. If you need to assemble the swing arm by yourself, please refer to the diagram below for

installation.

Note: The swing arm is already installed in the factory.

①

②

ZKTeco Industrial Park, No. 32, Industrial Road,

Tangxia Town, Dongguan, China.

Phone : +86 769 - 82109991

Fax : +86 755 - 89602394

www.zkteco.com

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere ZKTeco Drehkreuz Handbücher

ZKTeco

ZKTeco TS2000 Pro Series Bedienungsanleitung

ZKTeco

ZKTeco TS1000D Bedienungsanleitung

ZKTeco

ZKTeco SBT1000S Bedienungsanleitung

ZKTeco

ZKTeco FHT2300 Bedienungsanleitung

ZKTeco

ZKTeco TS1000 Pro Series Bedienungsanleitung

ZKTeco

ZKTeco SBT2000S Bedienungsanleitung

ZKTeco

ZKTeco FBL6000 Pro Series Bedienungsanleitung

ZKTeco

ZKTeco SBT2000S Bedienungsanleitung

ZKTeco

ZKTeco TS5000A Series Bedienungsanleitung

ZKTeco

ZKTeco TS1000 Pro Series Bedienungsanleitung

ZKTeco

ZKTeco TS1200 Series Bedienungsanleitung

ZKTeco

ZKTeco SBTL8000 Series Bedienungsanleitung

ZKTeco

ZKTeco TS5000A Series Bedienungsanleitung

ZKTeco

ZKTeco FBL6000 Pro Series Bedienungsanleitung

ZKTeco

ZKTeco Mars-B1000 Bedienungsanleitung

ZKTeco

ZKTeco TS1000 Series Bedienungsanleitung

ZKTeco

ZKTeco TS3000 Series Bedienungsanleitung

ZKTeco

ZKTeco TS1000 Pro Series Bedienungsanleitung

ZKTeco

ZKTeco TS2200 Series Bedienungsanleitung

ZKTeco

ZKTeco FHT2300 Bedienungsanleitung

ZKTeco

ZKTeco TS2000PRO Series Bedienungsanleitung

ZKTeco

ZKTeco mTS1000 Series Bedienungsanleitung

ZKTeco

ZKTeco TS1000 Pro Series Bedienungsanleitung

ZKTeco

ZKTeco Mars-S1011 Bedienungsanleitung

Beliebte Drehkreuz Handbücher anderer Marken

Oxgard

Oxgard CUBE C-10 Bedienungsanleitung

LBA GROUP

LBA GROUP LBAT10 Bedienungsanleitung

Magnetic

Magnetic mTripod Bedienungsanleitung

Kaba

Kaba Argus HSG-E02 Bedienungsanleitung

Automatic Systems

Automatic Systems TR491 Bedienungsanleitung

Turnstiles

Turnstiles HZ-SWGS01 Bedienungsanleitung

DSI

DSI DST-80 Bedienungsanleitung

OZAK

OZAK VP-125 Handbuch

Automatic Systems

Automatic Systems SMARTLANE SL 90X Bedienungsanleitung

Alvarado

Alvarado MT Montage- und Bedienungsanleitung

JKDC SECURITY

JKDC SECURITY JKDC-100C Bedienungsanleitung

Alvarado

Alvarado SU5000 Bedienungsanleitung

Magnetic Autocontrol

Magnetic Autocontrol MPT 33 Bedienungsanleitung

Oxgard

Oxgard Praktika T-04K Kurzanleitung

digicon

digicon CATRAX Plus Bedienungsanleitung

Oxgard

Oxgard CUBE C-04-s Bedienungsanleitung

BOON EDAM

BOON EDAM Turnlock 100 Leitfaden

Wano

Wano Tripod BO-DSN10 Bedienungsanleitung