ZKTeco SBT1000S Bedienungsanleitung

Swing Barrier Turnstile User Manual

Applicable Models: SBT1000S

Version: 1.2Date: May. 2018

Contents

Chapter 1 Product Introduction.............................................................................................................................................................. 1

1.1 Model number and access control....................................................................................................................................... 1

1.2 Chassis and dimensions............................................................................................................................................................... 1

1.3 Mechanical system .......................................................................................................................................................................... 1

1.4 Electronic control system............................................................................................................................................................ 1

1.5 The working principle of swing barrier turnstile system........................................................................................ 2

1.6 Product related parameters....................................................................................................................................................... 2

Chapter 2 The Installation of the Product......................................................................................................................................... 3

2.1 Installation notes............................................................................................................................................................................... 3

2.2 Installation position of the swing barrier turnstile...................................................................................................... 3

2.3 Cables installation and fixation................................................................................................................................................ 3

Chapter 3 Menu Operation......................................................................................................................................................................... 5

3.1 Function introduction................................................................................................................................................................... 5

3.2 Menu introduction........................................................................................................................................................................... 5

3.3 Wiring diagram and function ................................................................................................................................................... 7

Chapter 4 Product Maintenance............................................................................................................................................................. 8

4.1 Chassis maintenance...................................................................................................................................................................... 8

4.2 Movement maintenance............................................................................................................................................................. 8

4.3 Power maintenance........................................................................................................................................................................ 8

Chapter 5 Troubleshooting ........................................................................................................................................................................ 9

Chapter 1 Product Introduction

1.1 Model number and access control

Access

Model NO C3-200 with two

KR800 reader inBIO260 with two FR1500/ID reader

SBT1000S √

SBT1011S √

SBT1022S √

1.2 Chassis and dimensions

SBT1000S series, with stainless steel housing, provide simple and beautiful design with anti-corrosion.

It is provide orderly and civilized passage to people while eliminating illegal personnel access. In case

of emergency, it ensures timely evacuation channel smoothly and convenient personnel.

SBT1000S’s appearance and dimensions are as shown in Figure 1-2A:

Figure1-2A

1.3 Mechanical system

The mechanical system of a swing barrier turnstile includes the chassis and the core component. The

chassis is a carrier where the reader, the sensor, and the lock are installed. The core component

mainly consists of the motor, the frame and the swing arm.

1.4 Electronic control system

The electronic control system of a swing barrier turnstile is mainly composed of the reader, the

control panel, the access controller, the sensor and the transformer.

Reader: The reader reads the data in the card and sends it to the controller.

Control panel: The control panel is the system’s control center that receives signals from the access

controller, performs logical judgment and processing of these signals, and sends executive

commands to the electric motor.

IR sensor: anti-pinch function.

1.5 The working principle of swing barrier turnstile system

1) After powered on, the system performs self-check. If no failure is detected, the machine starts to

operate normally. If a failure is detected, the system displays related messages on the LCD

display screen so that the user can have a quick knowledge of and solve the problem.

2) When the reader detects a valid card, the buzzer will give a nice audible prompt to the

pedestrian, indicating that the card is being read successfully. And then, the reader sends signals

to the access controller to request permission to pass through the passage. If the signal is legal,

the access controller will send the open signal to the master control panel.

3) After receiving the signal from the access controller, the control panel sends valid control signals

to the electric motor and opens the barrier.

1.6 Product related parameters

Dimension(mm) SBT1000S: L=200, W=185, H=1100

Input voltage AC100-120V/200-

240V,50-60Hz Output voltage DC 24V

Input control signal Switching signal Relative humidity 20%-93%

temperature -28℃-60℃Pass speed Maximum: 30/minute

Infrared sensor 1 Working

environment Indoor/Outdoor（If shelter）

Air switch

Access controller

IR Sensor

24V power supply

Motor

Encoder

Control board

Clutch

Reader

Chapter 2 The Installation of the Product

2.1 Installation notes

1) It is recommended that the swing barrier turnstile be installed on a horizontal solid platform

with 50mm to 100mm in height.

2) It is recommended that the swing barrier turnstile should not be used in corrosive environment.

3) Make sure the protective earth wire of the system is reliably connected to avoid personal injuries

or other accidents.

4) After installation, check whether connection is reliable at the connecting points of the

protective earth wire, at the connector assemblies and wiring points of the circuits, as well as at

each movable part of the swing barrier turnstile. Any loose nuts, screws and other fasteners

should be tightened in time to avoid swing barrier turnstile failures caused by long-time

operations.

2.2 Installation position of the swing barrier turnstile

The installation position depends on the size of the swing barrier.If the swing barrier turnstile is

installed near a wall, a distance of 100mm between the swing barrier turnstile and the wall needs to

be reserved for ease of installing the device. The SBT1000S swing barrier turnstile may form a

channel, or form two channels with a SBT1000S swing barrier turnstile,as shown in figure 2-2A;

Figure2-2A SBT1000S Single channel and dual channel

2.3 Cables installation and fixation

For the outlets of the concealed cables, please refer to the drawing showing the mounting holes.

The input voltage for this swing barrier turnstile is AC100-120V/200-240V. The PVC conduits are

buried 100mm under the ground, with the height of the exposed part about exceeding 100mm. In

addition, the conduit outlet is bent back to prevent ingress of water into the conduit.

SBT1000S installation holes and cabling positions as shown in Figure 2-3A.

Figure 2-3A

Mark out the screw hole centers of the stand, and the edge of the chassis base on the ground

according to the sizes as shown on the figure 2-3A. Use a hammer drill to perforate M12 screw holes

and then install the screws. Place the swing barrier turnstile according to the sizes and positions as

shown in the figure before installation and fixation. Connect to the power and test. If the test is OK,

tighten the screws. It is recommended that a warning line be marked out on the ground after the

machine is installed, so as to prompt the pedestrian to stand behind the warning line when swiping

the card. As shown in Figure 2-3B.

Figure 2-3B

Chapter 3 Menu Operation

3.1 Function introduction

There are 4 keys on the control panel, including "UP", "DOWN", "ENT" and "ESC".

UP: to move up menu item or increase the value.

DOWN: to move down menu item or increase the value.

ENT: to enter setting menu item or confirm the current modified value.

ESC: to return the previous menu or cancel the current operation.

Operation and instruction of menu

Press the ENT button, enter the password input interface, the default password is: UP, UP, DOWN,

DOWN, DOWN, DOWN. If any step fails, please press the ESC button to get back. After entering the

menu press UP or DOWN to choose a menu item and then press ENT to enter the interface and

adjust function or value.

3.2 Menu introduction

1. Correct barrier position

1) Zero position

2) Left opening position

3) Right opening position

Press “ENT” key to modify. Press “UP/DOWN” to select correction type. Press “ESC” to exit. Default

value is Zero position.

2. Open duration time

After the gate is open, it will automatically close if no one passes.

Press ''ENT'' key to modify. Press “UP/DOWN” to select open duration time, press ''ESC'' to exit.

Adjustable range from 5 to 60, default value is 10 seconds.

3. Speed of gate

1) low speed

2) medium speed

3) high speed

Press ''ENT'' key to modify, press “UP/DOWN” to select speed, press ''ESC'' to exit.

Setting succeeds, device running 10 times will change effect, default value is medium speed.

4. Opening mode setting

1) Bi-direction swiping card

2) Left direction swiping card

3) Right direction swiping card

4) Bi-directional prohibition

Press ''ENT'' key to modify, press “UP/DOWN” to select opening mode, press ''ESC'' to exit.

The default value is Bi-direction swiping card.

5. Min speed compensation

Adjustable range from 0 to 20.

Press ''ENT'' key to modify, press “UP/DOWN” to select compensation, press ''ESC'' to exit.

The default value is 0.

6. Delay closing gate time

Adjustable range from 2 to 10.

After pedestrian passes through the last infrared sensor, the gates will keep opening the time

what you set, then close immediately.

Press ''ENT'' key to modify, press “UP/DOWN” to select delay closing gate time, press ''ESC'' to exit,

default value is 5 seconds.

7. Brake starting angle

Adjustable range from 3 to 10 degrees.

Press ''ENT'' key to modify, press “UP/DOWN” to select brake angle, press ''ESC'' to exit.

The default value is 3 degrees.

8. Unlock brake method.

About the method of unlocking, it uses delay release. The time of the delay is affected by the

times of lock. The first lock takes 2s, second lock takes 2s, third lock takes 4s, and then it's all 4s. In

this process, if the swing arm is back where it should have been before, it will reset the time.

9. Firefighting signal setting

1) Open

2) Close

Press ''ENT'' key to modify, press “UP/DOWN” to select fighting signal, press ''ESC'' to exit.

The default value is open; it is required firefighting device connection with fire port.

10. System working mode

1) Work mode

2) Auto test

3) System initialization

Press ''ENT'' key to modify, press “UP/DOWN” to select system working mode, press ''ESC'' to exit,

default value is work mode.

11. Volume setting

1) Adjustable range from 1 to 16, default value is 5.

2) Close sound

Press ''ENT'' key to modify, press “UP/DOWN” to select volume level, press ''ESC'' to exit.

The default value is 5.

12. IR anti-pinch setting

When the gate closes, if the infrared sensors is triggered, the swing arm stops moving.

13. Version

V2.1.2

3.3 Wiring diagram and function

Check circuit according to the following wiring diagram:

Functions of terminals at each zone:

Power input 24V: The voltage is changed by a transformer to 24V and supplied to the control panel.

Firefighting port: During emergencies ensuring users fast unencumbered exit to safety.

Right open (DOWN button), left open (UP button): Controls the barrier to open to left or right

side.

Access control power supply: Supplies power for the access board.

RS485 communication port: Receiving external signals.

Electromagnetic clutch: It is connected to the electromagnet inside the core component to

prevent collision and pinch.

Connecting cable of the motor: It is connected to the motor and supplies power to the motor.

LED light: Connect to the light belt on the top of the device.

IR Sensor: It is connected to the infrared sensor to achieve anti-pinch function.

Encoder: It is connected to the encoder to determine the position of the barrier.

UP DOWN ENT ESC

Reader

Reader 2

485 Reader

GND

Lock1

Lock2

485A EGND 458B

IR7

IR8

IR6

IR5

IR3

IR4

IR2

IR1

2VN

V5V

ZUO YOU GND 12V

IN SW IN SW IN SW

C-

-H

24VOUT GND

Encoder

lectromagne

ticclutch

NDVC

VCC GND VCC GND

DVC

VCC GND

AP-R：IR3

IR3 on the top

SPK

24V

Firefighting port

SBT1000S series

Wiring diagram

Firefightingboa

LED light

KR800

Infrared sensor

Motor

Chapter 4 Product Maintenance

4.1 Chassis maintenance

The chassis is made up of 304 stainless steels. There may be rust stains on its surface after using for a

long time. Regularly sand the surface along the grain softly and carefully, Coat the surface with

anti-rust oil, do not cover the infrared sensor.

4.2 Movement maintenance

Cut off power supply before maintenance. Open the door, clean surface dust, apply butter to the

transmission mechanism. Check and tighten others connection parts.

4.3 Power maintenance

Cut off power supply before maintenance. Check whether the plug is loose, if loose need to tightly it,

do not replace the connection position at random, check whether the external power supply is

exposed, timely wrapped, whether there is any leakage, timely treatment. Check the technical

parameters of interface is normal, the aging of electronic components to be replaced.

(Attention: Above swing barrier maintenance must be maintained by professional personnel.

Especially the movement and the electric control part, first cut off the power supply, ensure the

operation safety.)

Andere Handbücher für SBT1000S

Inhaltsverzeichnis

Andere ZKTeco Drehkreuz Handbücher

ZKTeco

ZKTeco SBT2000S Bedienungsanleitung

ZKTeco

ZKTeco TS1000 Pro Series Bedienungsanleitung

ZKTeco

ZKTeco SBTL8000 Series Bedienungsanleitung

ZKTeco

ZKTeco Mars-S1000 Bedienungsanleitung

ZKTeco

ZKTeco TS1000 Pro Series Bedienungsanleitung

ZKTeco

ZKTeco Mars-F1000 Bedienungsanleitung

ZKTeco

ZKTeco SBT2000S Bedienungsanleitung

ZKTeco

ZKTeco Mars-B1000 Bedienungsanleitung

ZKTeco

ZKTeco Mars-F1000 Bedienungsanleitung

ZKTeco

ZKTeco TS3000 Series Bedienungsanleitung

ZKTeco

ZKTeco SBTL7000 Series Bedienungsanleitung

ZKTeco

ZKTeco TS1000 Series Bedienungsanleitung

ZKTeco

ZKTeco TS1000 Pro Series Bedienungsanleitung

ZKTeco

ZKTeco TS5000A Series Bedienungsanleitung

ZKTeco

ZKTeco TS2000 Series Bedienungsanleitung

ZKTeco

ZKTeco TS5000A Series Bedienungsanleitung

ZKTeco

ZKTeco TS1000D Bedienungsanleitung

ZKTeco

ZKTeco TS2000 Pro Series Bedienungsanleitung

ZKTeco

ZKTeco SBT1000S Bedienungsanleitung

ZKTeco

ZKTeco Mars-S1011 Bedienungsanleitung

ZKTeco

ZKTeco Mars Pro-S1000 Bedienungsanleitung

ZKTeco

ZKTeco TS2000PRO Series Bedienungsanleitung

ZKTeco

ZKTeco FHT2300 Bedienungsanleitung

ZKTeco

ZKTeco FBL6000 Pro Series Bedienungsanleitung

Beliebte Drehkreuz Handbücher anderer Marken

Oxgard

Oxgard CUBE C-10 Bedienungsanleitung

LBA GROUP

LBA GROUP LBAT10 Bedienungsanleitung

Magnetic

Magnetic mTripod Bedienungsanleitung

Kaba

Kaba Argus HSG-E02 Bedienungsanleitung

Automatic Systems

Automatic Systems TR491 Bedienungsanleitung

Turnstiles

Turnstiles HZ-SWGS01 Bedienungsanleitung

DSI

DSI DST-80 Bedienungsanleitung

OZAK

OZAK VP-125 Handbuch

Automatic Systems

Automatic Systems SMARTLANE SL 90X Bedienungsanleitung

Alvarado

Alvarado MT Montage- und Bedienungsanleitung

JKDC SECURITY

JKDC SECURITY JKDC-100C Bedienungsanleitung

Alvarado

Alvarado SU5000 Bedienungsanleitung

Magnetic Autocontrol

Magnetic Autocontrol MPT 33 Bedienungsanleitung

Oxgard

Oxgard Praktika T-04K Kurzanleitung

digicon

digicon CATRAX Plus Bedienungsanleitung

Oxgard

Oxgard CUBE C-04-s Bedienungsanleitung

BOON EDAM

BOON EDAM Turnlock 100 Leitfaden

Wano

Wano Tripod BO-DSN10 Bedienungsanleitung