Zonestar Z8PM4 Pro Bedienungsanleitung

Model: Z8PM3(4)Pro

User Guide

!! ATTENTION !!

Please put the printer away from the reach of kids.

Must be guided by adults when children are installed or used.

Take care when installation, to avoid electrical shock hazards.

Please keep well-ventilated condition! May produce toxic gases when

printer working.

Caution: Hot!

Hotend has high temperature even the printer stop working.

Caution: Hot!

Hotbed has high temperature even the printer stop working.

Please strictly follow the standard operation when installation.

Please make sure you have set the AC power select switch to the

correct position before power on.

The newest documents download link:

https://github.com/ZONESTAR3D/Z8P

Parts List

No.

Name

Check

No.

Name

Check

Base Module

□

Contol Panel

□

Extruders

(3 sets for M3 and 4 sets for M4)

□

Scews, lead screws fix blocks,

ENDSTOPs, Fittings,

PTFE Tubes, belt, cable tie, etc.

□

Z-axis Motor Modules (2 sets)

□

Filament Roll Bracket

□

Lead screw & Profiles

□

USB cable

□

Print head with bracket

M3 or M4 hotend

□

Tools

□

Z carrier left

□

SD card, Card Reader, Gift filament

□

Z carrier right

□

Power cord

□

1 32 5 6 7

9 131211

Parts

2x Z aluminum profiles, there are 4 taping hole on the end

There are 2 hole on the bottom side

These two holes on the bottom

when install

1x top aluminum profile, there are many hole on the front

1x X Profile, 2020-420mm, There are two big hole on the back

2x lead screws insert into the Z profie (They are put inside the Z aluminum profiles)

20* M4x18

8* M4x25

Z ENDSTOP

X Belt idler

PTFE Tube X Timing Belt

Z lead screw

fix blocks

Install Z axis Parts

M4x25 *4

M4x18 *4

2040V profiles

Install Z profiles to base

Z ENDSTOPs

Install Zmotor module to the Z profiles

Install Z ENDSTOPs module to the out side of the Z profiles

About 18mm

NOTE:

There are two hole

on the profile, let the

side with holes on the

bottom.

M4x18 *2

Install Z axis Parts

Install Z Carrier Install lead screws

Through the

copper nut

Fixed on the Coupling

of Z axis motor

Install Top profile

M4x25 *4

Top profile

Note:

Adjust the eccentric

cloumns let the carrier

hold the rail well and

move smoothly.

Install X axis Parts

M4x18 *4

X Profile

Install the X belt idler to the Z right

carrier, move it from right to left

Install the X profile to

the Z carrier

Install X belt idler and X profile

Install X axis Parts

Slide in the hotend from

the right to left

Layout the hotend cable

Keep the same heigth

Before fixed the X profile

Install X profile

Install print head (hotend assembly)

Move X belt idler to the right

after fixed the belt

Install X belt

Move X belt idler to the left

before fix the belt

Tigthen the X belt

Install the X belt

X Timing Belt

Hotend

(the hotend be hide in this picture)

Adjust the eccentric

cloumns, let the X

carrier hold the rail well

and move

smoothly

Install the other parts

Install the LCD screen on the right/bottom of printer

Z8-M3 is 3 sets and Z8-

M4 is 4 sets

Install the filament roll bracket to the top of the frame

Connect the extrusion feeder with the print head

by filament guide (PTFE tube)

NOTE: One of the channels is connected and

others closed by hotend clean tool when the

machine left factory. If you don't have

experience in using 3D printers, start with

single color.

Install Extrusion feeders to the top of the frame

M4x18 *6(8)

x 3 or 4

NOTE: Try to rotate the extruders a little when install

to keep a little clearance between the adjusting

screw and the indenter.

M4x18 *2

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Zonestar 3D-Drucker Handbücher

Zonestar

Zonestar P802QS Bedienungsanleitung

Zonestar

Zonestar P802QS Bedienungsanleitung

Zonestar

Zonestar P802QS Bedienungsanleitung

Zonestar

Zonestar Z5 Series Bedienungsanleitung

Zonestar

Zonestar P802-STS Bedienungsanleitung

Zonestar

Zonestar Z8X Bedienungsanleitung

Zonestar

Zonestar Z9 Series Bedienungsanleitung

Zonestar

Zonestar Z6 Bedienungsanleitung

Zonestar

Zonestar P802CR2 Bedienungsanleitung

Beliebte 3D-Drucker Handbücher anderer Marken

Ultimaker

Ultimaker S5 Material Station Bedienungsanleitung

EcubMaker

EcubMaker TOYDIY Bedienungsanleitung

AnyCubic

AnyCubic Kossel Plus Bedienungsanleitung

ReDeTec

ReDeTec ProtoCycler Bedienungsanleitung

Kywoo3D

Kywoo3D Tycoon IDEX Bedienungsanleitung

CraftBot

CraftBot PLUS PRO Bedienungsanleitung

3DGence

3DGence INDUSTRY F340 Bedienungsanleitung

HP Jet Fusion 4200 Betriebsanleitung

Rokit

Rokit AEP Series Bedienungsanleitung

AnkerMake

AnkerMake M5 Bedienungsanleitung

DIYElectronics

DIYElectronics PRUSA I3 Montageanleitung

Ackuretta

Ackuretta FreeShape 120 Bedienungsanleitung

LONGER

LONGER LK5Pro Bedienungsanleitung

Stratasys

Stratasys J850 Bedienungsanleitung

MakerBot

MakerBot Replicator Bedienungsanleitung

Stratasys

Stratasys FDM Vantage Series Bedienungsanleitung

ZYYX

ZYYX Pro II Bedienungsanleitung

FLASHFORGE 3D PRINTER

FLASHFORGE 3D PRINTER Creator Benutzerhandbuch