Zte MF920 Bedienungsanleitung
4G/Wi-Fi hotspot “Beeline”
Internet at home and outdoor
Appearance and review of 4G/Wi-Fi hotspot
controls
Appearance
1. Micro U B connector for connection to computer or charger.
2. LED indicators.
3. Power button. Hold button to turn on/off the device.
4. WP button (Wi-Fi protected setup) and on/off Wi-Fi. Hold button for 5 seconds to activate
WP . hort press to turn on/off Wi-Fi function.
5. U IM card slot.Reset button to reset factory defaults.
LED indicators status description
Indicat
or Name tatus Description
Battery
Blinking red Critical battery level. Please, connect
charger.
olid red Low battery.
Blinking
green Charging battery.
olid green Middle battery level or battery is fully
charged.
Off
Device is turned off, in stand by mode
and not charging, or battery is
removed.
Network signal
olid red Error. No network or U IM card not
inserted.
olid green Registered in 2G/3G network.
Blinking gree
n
Registered in 2G/3G network and
connected to Internet. Data transfer is
active.
olid blue Registered in 4G network.
Blinking blue
Registered in 4G network and
connected to Internet. Data transfer is
active.
M
olid blue Unread M .
Blinking blue New M and shines for 10 seconds,
or Full M .
Off No unread M and no new M , or in
power saving mode.
Wi-Fi network olid blue Wi-Fi active.
Blinking blue WP active.
How to use device
To install the router, follow step-by-step instruction to make sure that you have done all correctly.
Getting started
tep 1. Installation of U IM card
1. Remove flip on side of the device.
2. Insert U IM card into the router in right direction. Make sure that U IM card is tightly inserted.
Attention: Correct work of router and software is guaranteed only with "Beeline" U IM.
3. To reset MF 920 to factory defaults press button as per picture below.
Note: You can write or remember network ID and password of Wi-Fi network. It will be need it if you
plan to connect to router via Wi-Fi.
tep 2. Power on
Hold power button on body of device and do not release, before LED indicators will be turned on.
tep3. Connection router with other devices
Connection via U B cable
Connect U B cable to router, then connect U B jack to any free U B port of PC.
Connection via Wi-Fi
1. Make sure that your router is turned on.
2. tart searching wireless networks on device, which you want connect to router.
Note: you must set automatically obtain IP address in device settings, which you are going to connect
with router.
3. In wireless networks list choose needed network name ( ID).Router have following name
format: Beeline_XXXX, where XXXX –number, which is unique for each router. Also you can find name
of network under back cover of your router in the top.
4. Password input will be required. You can find password under back cover of your router after
network name ( ID).
5. After successful connection with router you can open your WEB browser and enter to address
bar: http://m.home or http://192.168.8.1 to access to WEB UI of your router.
tep 4. Installing the application
If you connect your device with router via U B, installation of the "4G/Wi-Fi hotspot “Beeline”" application
starts automatically after a time. Wait installation program starts and follow its prompts. During installation
do not disconnect the router from PC.
PC’s with Microsoft® Windows® O
Installation of the 4G/Wi-Fi hotspot "Beeline" application starts automatically after a time. Wait installation
program starts and follow its prompts. During installation do not disconnect the router from PC. If automatic
installation fails to start, install it manually:
1. Open Computer. To make it, double click the icon Computer on the desktop. If there is no
icon Computer on the desktop, press simultaneously Windows key and E key on your keyboard
and select Beeline disc in the opened window.
2. In the Computer window open Beeline disc. On some PC due to security settings no disk
name can be seen. If no Beeline disk is found in Computer, open newly appeared external disk (e.g.
CD ROM (E:)).
3. In the appeared window find AutoRun.exe and run it.
4. Then follow the installation program prompts and do not disconnect the ruter from PC.
PC’s with Apple Mac O X
1. Open the disk Beeline, which appears on the desktop.
2. If there is no any Beeline disk on the desktop, then press keyboard keys simultaneously
and on the left side of the opened Devices window select Beeline disk.
3. In the opened window look for 4G-Wi-Fi router "Beeline" installation file and execute it.
4G/Wi-Fi hotspot “Beeline”
Internet at home and outdoor
Appearance and review of 4G/Wi-Fi hotspot
controls
Appearance
1. Micro U B connector for connection to computer or charger.
2. LED indicators.
3. Power button. Hold button to turn on/off the device.
4. WP button (Wi-Fi protected setup) and on/off Wi-Fi. Hold button for 5 seconds to activate
WP . hort press to turn on/off Wi-Fi function.
5. U IM card slot.Reset button to reset factory defaults.
LED indicators status description
Indicat
or Name tatus Description
Battery
Blinking red Critical battery level. Please, connect
charger.
olid red Low battery.
Blinking
green Charging battery.
olid green Middle battery level or battery is fully
charged.
Off
Device is turned off, in stand by mode
and not charging, or battery is
removed.
Network signal
olid red Error. No network or U IM card not
inserted.
olid green Registered in 2G/3G network.
Blinking gree
n
Registered in 2G/3G network and
connected to Internet. Data transfer is
active.
olid blue Registered in 4G network.
Blinking blue
Registered in 4G network and
connected to Internet. Data transfer is
active.
M olid blue Unread M .
Blinking blue New M and shines for 10 seconds,
or Full M .
Off No unread M and no new M , or in
power saving mode.
Wi-Fi network olid blue Wi-Fi active.
Blinking blue WP active.
How to use device
To install the router, follow step-by-step instruction to make sure that you have done all correctly.
Getting started
tep 1. Installation of U IM card
1. Remove flip on side of the device.
2. Insert U IM card into the router in right direction. Make sure that U IM card is tightly inserted.
Attention: Correct work of router and software is guaranteed only with "Beeline" U IM.
3. To reset MF 920 to factory defaults press button as per picture below.
Note: You can write or remember network ID and password of Wi-Fi network. It will be need it if you
plan to connect to router via Wi-Fi.
tep 2. Power on
Hold power button on body of device and do not release, before LED indicators will be turned on.
tep3. Connection router with other devices
Connection via U B cable
Connect U B cable to router, then connect U B jack to any free U B port of PC.
Connection via Wi-Fi
1. Make sure that your router is turned on.
2. tart searching wireless networks on device, which you want connect to router.
Note: you must set automatically obtain IP address in device settings, which you are going to connect
with router.
3. In wireless networks list choose needed network name ( ID).Router have following name
format: Beeline_XXXX, where XXXX –number, which is unique for each router. Also you can find name
of network under back cover of your router in the top.
4. Password input will be required. You can find password under back cover of your router after
network name ( ID).
5. After successful connection with router you can open your WEB browser and enter to address
bar: http://m.home or http://192.168.8.1 to access to WEB UI of your router.
tep 4. Installing the application
If you connect your device with router via U B, installation of the "4G/Wi-Fi hotspot “Beeline”" application
starts automatically after a time. Wait installation program starts and follow its prompts. During installation
do not disconnect the router from PC.
PC’s with Microsoft® Windows® O
Installation of the 4G/Wi-Fi hotspot "Beeline" application starts automatically after a time. Wait installation
program starts and follow its prompts. During installation do not disconnect the router from PC. If automatic
installation fails to start, install it manually:
1. Open Computer. To make it, double click the icon Computer on the desktop. If there is no
icon Computer on the desktop, press simultaneously Windows key and E key on your keyboard
and select Beeline disc in the opened window.
2. In the Computer window open Beeline disc. On some PC due to security settings no disk
name can be seen. If no Beeline disk is found in Computer, open newly appeared external disk (e.g.
CD ROM (E:)).
3. In the appeared window find AutoRun.exe and run it.
4. Then follow the installation program prompts and do not disconnect the ruter from PC.
PC’s with Apple Mac O X
1. Open the disk Beeline, which appears on the desktop.
2. If there is no any Beeline disk on the desktop, then press keyboard keys simultaneously
and on the left side of the opened Devices window select Beeline disk.
3. In the opened window look for 4G-Wi-Fi router "Beeline" installation file and execute it.
4. After that follow installation program prompts and do not disconnect the router from Mac.
WEB UI for 4G/Wi-Fi hotspot “Beeline”
Open WEB UI for 4G/Wi-Fi hotspot “Beeline”. To do it, find icon on Desktop (for Windows O ) and
double click on it, in Mac O - find icon in Dock station.
Attention: if there is no icon on Desktop by some reasons, you can open WEB UI using your Internet
browser. Input in your browser IP address: 192.168.8.1 or WEB address: http://m.home.
Authorization. To access 4G/Wi-Fi hotspot settings you need to enter a password on the login page.
Default password - admin. Enter your password and click "Login”.
Main page. Contain links to all sections, and also information about current router status, network
information etc. Using main page functions, you can establish Internet connection, check your current
balance and move to any section of WEB UI for 4G/Wi-Fi hotspot “Beeline”.
# Name Description
1tatus bar,
language bar
tatus bar displays current U IM
card status, current network type
and signal strength.
Language bar allows you to quickly
switch WEB UI language.
2 Wi-Fi Info
On click will open Wi-Fi settings
section, which allows you configure
Wi-Fi, check current list of
connected devices via Wi-Fi.
3 Connect tile
Allows you to establish connection
with Internet, also will display
current connections status and data
transfer rate. If connection to
Internet is not established, click on
this tile to establish connection. If
connection already established, on
click this connection will be closed.
4 Messages tile
On click will open Messages section,
for reading, sending and deleting
M . Also tile displays the last
incoming message, on click will
open directly this message text.
5 ettings tile On click will open ettings section
for modify current device settings.
6Personal
account
On click will open the
portalhttp://my.beeline.ru/ ,allows
you to manage services online.
7 Account status
On click will open the
portalhttps://balance.beeline.ru/ ,allow
ing to display the online account
balance.
8Manage
ervices tile
On click will open Manage ervices
section for sending U D
commands, for checking current
balance, phone number etc.
9 Help tile On click will open Help section with
information about device.
10 Check balance
tile
Allows you to check your current
balance.
Internal pages. All internal pages made using one template. Each page contain information and control
elements according with section name.
# Name Descrption
1 ection header
Displays current section
title. On click will open
main menu, which allows
you to move between
main sections of WEB UI.
2 Home button
On click will open main
page of WEB UI from any
section or subsection.
3tatus bar, language
bar
tatus bar displays current
U IM card status, current
network type and signal
strength.
Language bar allows you
to quickly switch WEB UI
language.
4 ection menu tile
Displays current section
menu. Allows you to
switch between
subsections of current
section.
5 ubsection header
Displays current
subsection title. If you see
nearby with subsection
name icon of drop down
menu , on click will
open 3rd level menu of
subsection. Use this menu
to switch between
functions of current
subsection.
6 ubsection content Display current
subsections content.
7 Connection status tile On click allows you to
connect/disconnect your
Inhaltsverzeichnis
Andere Zte Netzwerk-Router Handbücher
Zte
Zte ZXR10 ZSR Bedienungsanleitung
Zte
Zte MC888 Bedienungsanleitung
Zte
Zte ZXR10 ZSR Bedienungsanleitung
Zte
Zte MC801A Bedienungsanleitung
Zte
Zte ZXR10 T8000 Series Handbuch
Zte
Zte WiFi MF20 Bedienungsanleitung
Zte
Zte MC801A1 Bedienungsanleitung
Zte
Zte Avid 4G LTE Bedienungsanleitung
Zte
Zte MC889 Bedienungsanleitung
Zte
Zte ZXR10 2900E Series Installationshandbuch
Zte
Zte GPON ONT ZXHN F600 Bedienungsanleitung
Zte
Zte T3000 Bedienungsanleitung
Zte
Zte MF28B Bedienungsanleitung
Zte
Zte MF93D Bedienungsanleitung
Zte
Zte MF25A Bedienungsanleitung
Zte
Zte WF820 Bedienungsanleitung
Zte
Zte ZXV10 W300 Bedienungsanleitung
Zte
Zte ZXHN H560N Bedienerhandbuch
Zte
Zte mf910l Bedienungsanleitung
Zte
Zte MF65M Bedienungsanleitung
Beliebte Netzwerk-Router Handbücher anderer Marken
NETGEAR
NETGEAR FS526T - Switch Bedienungsanleitung
Korenix
Korenix JetNet 5710G Series Bedienungsanleitung
Automated Logic
Automated Logic ZN551 Betriebsanleitung
Cisco
Cisco ASR 1000 Series Bedienerhandbuch
EnGenius
EnGenius ESR-9710 Bedienungsanleitung
Cisco
Cisco 805 Series Bedienungs- und Sicherheitshinweise