ZyXEL Communications P-794H Bedienungsanleitung

www.zyxel.com

8 wire G.SHDSL CPE with 4 port

LAN

Firmware Version S04.01

Edition 1, 12/2010

P-794H

DEFAULT LOGIN DETAILS

IP Address: http://192.168.1.1

Username admin

Password 1234

ZyXEL Communications Corporation

Device Panels

POWER

LED

DSL

LED 1-4

CO LED

AC POWER

LAN

PORT 1-4

LAN

LED 1-4

CID

PORT

DSL

PORT 1-2

ALARM

LED

GROUNDING

TERMINAL

RESET

SWITCH

Requirements

Make sure you have the following things before you start.

• INTERNET ACCESS: You need an Internet account with an ISP

(Internet Service Provider) and information such as user name,

password, and so on.

•

WEB BROWSER

: Internet Explorer 6.0 and later versions, with

JavaScript enabled, or Mozilla Firefox 3 and later versions or Safari

2.0 and later versions. The browser will be used to access the Internet

and/or access the P-794H’s Web Configurator.

Hardware Connections

1. F.G.: Ground the P-794H by connecting a grounded wire to the F.G.

(Frame Ground) of the P-794H.

2. DSL: If you are using the P-794H with Internet access, use a

telephone wire to connect one of the DSL ports to the telephone wall

jack for Internet access.

If you are using the P-794H for point-to-point connection in CO/CPE

mode, use telephone wires to connect one or both (for maximum

speed) DSL ports to the other DSL port(s) of another P-794H.

Refer to page 9and the Tutorials chapter in User’s Guide for more

information about the P-794H operating in CO/CPE mode.

3. LAN: Use an Ethernet cable to connect a computer to one of these

ports for initial configuration. If you are operating in CO mode,

connect the LAN port to a router for Internet access.

4. CID: If you want to configure the P-794H by CLI command, use a

console cable to connect the CID port to your computer’s COM port.

This is for service technicians only.

5. AC Power: Use the power adaptor provided to connect an

appropriate power source to this socket.

Make sure the Reset switch is pointing up before powering

up the P-794H. Do not push the switch down unless you

want to reset the P-794H to the factory default settings.

Look at the LEDs (lights) on the top panel of the P-794H.

• The PWR light is on once the P-794H is turned on.

• The LAN light is on if the corresponding LAN port is properly

connected. If you do not connect a computer correctly to this port,

the LAN light will not turn on.

• The CO light is on when the P-794H is operating in CO mode. The

CO light is off when the P-794H is operating in CPE mode.

• The DSL lights blink slowly when there is no DSL connection and

blink rapidly when it is setting up a connnection. Once the DSL

connection is successful, the DSL lights are on.

The LAN lights blink rapidly when the P-794H is sending or receiving

data. If the ALM light is on, there is a connection problem.Try turning the

P-794H off, check the connections, wait a few seconds and then turn it

back on. If the problem persists, you may have a hardware problem and

you need to contact your vendor.

The Web Configurator

The Web Configurator is a web browser tool that allows you to configure

the P-794H. The computer and the P-794H need to be in the same IP

address range to use this tool.

1. Open your browser and enter http://192.168.1.1 (the P-794H’s

default IP address) as the address.

If you cannot access the Web Configurator, make sure the IP address

and subnet mask of the ZyXEL Device and the computer are in the same

IP address range. See your User's Guide for information on setting up

your computer's IP address.

To login, enter username

admin

and password

1234

(default). Click

If the login screen does not open, make sure you allow web

browser pop-up windows, JavaScript and Java permissions.

Your computer should also be set to get an IP address

automatically from a DHCP server. See your User’s Guide

for more information.

Internet Access Setup

Open your web browser and browse to http://www.zyxel.com. You may

be prompted to enter your username and password.

If the web page opens correctly, your P-794H is ready for you to use. If

the web page does not open, you need to enter your Internet access

configuration using the Web Configurator - see page 6. You should have

the information provided by your ISP.

1. You can manually configure the Internet connection. Log in the Web

Configurator. Click Configuration > WAN Connection. Click Create

a new service.

2. Select the Internet mode and encapsulation (PPPoE routed) used by

your ISP. Then click Configure.

3. Enter a description for the connection. If your IP address is assigned

by your ISP, enter it in the WAN IP addess field. If not, leave it as

0.0.0.0. Type your account username and password. Click

Configure.

If you are using static IP, go to

Configuration > DNS Relay

and enter

the primary DNS servers’ IP addresses. Click

Apply

to finish the setup.

Internet

Account

Point-to-Point Setup

You can setup two P-794Hs for fast point-to-point connection by setting

one P-794H as the CO and the other P-794H as the CPE and connecting

their DSL ports. The two P-794Hs and the computers can be in the same

DHCP domain but must have different IP addresses.

CO Mode

Log into the P-794H you are using as the CO. Click SHDSL > SHDSL

Configuration and select CO in the Unit ID field. Click Apply.

CPE CO

192.168.1.2

192.168.1.1

192.168.1.3

192.168.1.4

CPE Mode

Log into the P-794H you are using as the CPE. Click SHDSL > SHDSL

Configuration and select CPE in the Unit ID field. Make sure the other

settings on this screen are the same as SHDSL settings of CO. Click

Apply.

1. Connect the DSL ports of the CO to the DSL ports of the CPE with the

provided telephone wires. The DSL lights will be blinking. Wait for 1-2

minutes as the P-794Hs establish the connection. The DSL lights will

stop blinking once the connection is successful.

2. To test the connection, you can ping the CPE from the CO or the

other way around. If there is response, the connection is ready. If

there is no response, check your DSL connections and also see if the

SHDSL screen settings of the CPE are the same as the CO’s.

Andere Handbücher für P-794H

Inhaltsverzeichnis

Andere ZyXEL Communications Tor Handbücher

ZyXEL Communications

ZyXEL Communications VMG1312-B Series Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications VSG-1200 V2 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications ZyXEL Prestige 304 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications EMG6726-B10A Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications ZyWALL 70 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications VSG1432 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications VWG1312-B10A Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications MAX208M Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications G-4100 v2 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications p-661hw series Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications P-660HW-Tx v3 Series Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications ZyWall Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications P-2302R-P1C Handbuch

ZyXEL Communications

ZyXEL Communications P-662H-D Series Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications VSG-1200 V2 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications ZyXEL ZyAIR B-220 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications P-660HNT1 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications SBG3500-N000 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications AMG1001-T Series Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications p-2302r series Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications ZyWALL USG 2000 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications P-660HW-Tx v3 Series Handbuch

ZyXEL Communications

ZyXEL Communications P-660HW-Tx v3 Series Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications EMG3525-T50B Bedienungsanleitung

Beliebte Tor Handbücher anderer Marken

LST

LST M500RFE-AS Bedienungsanleitung

Kinnex

Kinnex Media Gateway Bedienungsanleitung

2N Telekomunikace

2N Telekomunikace 2N StarGate Bedienungsanleitung

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries Superlink SC-WBGW256 Bedienungsanleitung

Telsey

Telsey CPVA 500 - SIP Bedienungsanleitung

RTA

RTA 460A-NNA4 Technisches Datenblatt

Shaw

Shaw Gateway HDPVR Bedienungsanleitung

ABB

ABB VSN900 Kurzanleitung

Commander

Commander Pulse Bedienungsanleitung

2N Telekomunikace

2N Telekomunikace ATEUS EasyGate 501309E Bedienungsanleitung

NETGEAR

NETGEAR C6300BD Bedienungsanleitung

Amit

Amit CDW531AM Bedienungsanleitung

HMS

HMS Netbiter EasyConnect EC150 Bedienungsanleitung

Huawei

Huawei EchoLife HG620 Bedienungsanleitung

AT&T

AT&T U-verse 3801 Gebrauchs- und Pflegehandbuch

Logic IO

Logic IO RTCU MX2 turbo Bedienungsanleitung

Suttle

Suttle MediaMAX MXM-521 Bedienungsanleitung

RTA

RTA 460MCBC-N2E Technisches Datenblatt