ZyXEL Communications Omni ADSL LAN Bedienungsanleitung

Installation guide • 3

Руководство по установке • 11

Інструкція з установлення • 19

External ADSL modem for LAN

Внешний ADSL-модем для локальной сети

Зовнішній ADSL-модем для локальної мережі

ENGLISH

Installation guide

No part of this publication may be reproduced in any form or by any means without written permission from

the publisher. This publication is subject to change without notice. ZyXEL Communications Corporation does

not assume any liability arising out of errors that can be found in this guide. Trademarks mentioned in this

manual are used for informational purposes only and are properties of their respective owners. Information on

certificates numbers and terms could be obtained on corporate Internet server at http://www.zyxel–europe.com

Unpacking your modem

Before you install your modem, check the package and compare its contents to the list below to make sure that

no part is lost. The complete package should include:

• ZyXEL OMNI ADSL LAN modem

• Installation Guide

• 220V AC power adapter

• Ethernet cable

• Splitter

• Two phone cables

• CD with support documents

If one or more items from this list are missing, please contact your dealer immediately.

Registrering owner's rights

You can register your modem on the Internet at http://www.zyxel–europe.com

By registering on the Internet, you will get an additional year of warranty as well as other benefits.

ENGLISH

PORT CONNECTION

DSL

Connect the DSL jack on the OMNI ADSL LAN to the ADSL jack on the splitter using

included telephone wire. Connect telephone to the TEL jack on the splitter. Connect wall

jack to the LINE jack on the splitter.

Be careful not to insert an RJ-11 connector into the RJ-45 port.

LAN 10/100M

Use an Ethernet cable to connect this port to a computer (with an Ethernet card)

or a Switch (if your network has more than one computer). The port is auto-negotiating

(can connect at 10 or 100Mbps) and auto-crossover (automatically adjusts to the type

of Ethernet cable you use (straight-through or crossover)).

RESET You only need to use this button if you have forgotten the OMNI ADSL LAN’s password

or IP address. It returns the OMNI ADSL LAN to the factory defaults.

POWER Connect the end of the included power adapter for your region to this power socket.

OMNI ADSL LAN Rear Panel Connections

ENGLISH

LED COLOR STATUS DESCRIPTION

PWR Green On The OMNI ADSL LAN is receiving power

Off The OMNI ADSL LAN is not receiving power

SYS Green

On The OMNI ADSL LAN is functioning properly

Blinking The OMNI ADSL LAN is restarting

Off The OMNI ADSL LAN is not ready or has malfunctioned

Red On The power to the OMNI ADSL LAN is too low

LAN 10M Green

On The OMNI ADSL LAN has a successful 10Mbps Ethernet

connection

Blinking The OMNI ADSL LAN is receiving or sending data

Off No device is connected at 10Mbps

LAN 100M Orange

On The OMNI ADSL LAN has a successful 100Mbps Ethernet

connection

Blinking The OMNI ADSL LAN is receiving or sending data

Off No device is connected at 100Mbps

DSL Green

On The OMNI ADSL LAN is linked successfully to a DSLAM

Blinking The OMNI ADSL LAN is initializing the DSL line

Off The DSL link is down

PPP/ACT Green Blinking The OMNI ADSL LAN is receiving or sending data

Off The OMNI ADSL LAN is ready but not sending or receiving data

Orange On The OMNI ADSL LAN is initiating a PPPoE connection

Press the power switch in. The Power LED turns on. The SYS LED blinks and turns

steady on.The LAN and DSL LEDs turn on, if they are properly connected.

OMNI ADSL LAN Front Panel LED Description

ENGLISH

OMNI ADSL LAN Factory Defaults

LAN IP Address 192.168.1.1 Default Password 1234

Subnet Mask 255.255.255.0 DHCP IP Pool 192.168.1.33 – 192.168.1.64

Internet Account Information

Your ISP (Internet Service Provider) or telephone company should give you most of the following information or

pre-configured the OMNI ADSL LAN with it when you signed up for your Internet access account. You do not

need to know every field.

REQUIRED INFORMATION

Virtual Path Identifier (VPI):

Virtual Channel Identifier (VCI):

Multiplexing (VC-based or LLC-based): ❑VC ❑LLC

Your device’s WAN IP Address (if given):

Encapsulation:

❑RFC 1483

❑ENET ENCAP Ethernet Encapsulation Gateway IP Address:

❑PPPoA User Name: Password:

❑PPPoE (PPPoE) Service Name:

User Name: Password:

Preparing Your Network

All computers must have a 10M or 100M network card and TCP/IP installed. TCP/IP should already be installed

on computers using Windows NT/2000/XP, Macintosh OS 7 and later operating systems. See your User’s Guide

for information on configuring static IP address for your computer.

These procedures are for dynamic IP address assignment.

Setting up Your Windows 95/98/Me Computer

Installing TCP/IP Components

1. Click Start, Settings, Control Panel and double-click the Network icon.

2. The Network window Configuration tab displays a list of installed components.

To install TCP/IP:

a. In the Network window, click Add.

b. Select Protocol and then click Add.

c. Select Microsoft from the list of manufacturers.

d. Select TCP/IP from the list of network protocols and then click OK.

ENGLISH

Configuring TCP/IP

1. In the Network window Configuration tab, select your network adapter’s TCP/IP entry and click Properties.

2. Click the IP Address tab. Click Obtain an IP address automatically.

3. Click the DNS Configuration tab. Select Disable DNS.

4. Click the Gateway tab. Highlight any installed gateways and click Remove until there is none listed.

5. Click OK to save and close the TCP/IP Properties window.

6. Click OK to close the Network window.

7. Turn on your OMNI ADSL LAN and restart your computer when prompted.

Insert the Windows CD if prompted.

Verifying TCP/IP Properties

1. Click Start and then Run. In the Run window, type “winipcfg” and then click OK to open the IP Configuration

window.

2. Select your network adapter. You should see your computer’s IP address, subnet mask and default gateway.

Setting up Your Windows NT/2000/XP Computer

Configuring TCP/IP

1. Click Start, Settings, Network and Dial-up Connections and right-click Local Area Connection or the

connection you want to configure and click Properties. For Windows XP, click start, Control Panel, Network

and Internet Connections and then Network Connections. Right-click the network connection you want to

configure and then click Properties.

2. Select Internet Protocol (TCP/IP) (under the General tab in Win XP) and click Properties.

3. The Internet Protocol TCP/IP Properties window

opens. Click Obtain an IP address automatically.

4. Click Obtain DNS server automatically.

5. Click Advanced, IP Settings tab and remove any

installed gateways, then click OK.

6. Click OK to save and close the Internet Protocol

(TCP/IP) Properties window.

7. Click OK to close the Local Area Connection

Properties window.

8. Turn on your OMNI ADSL LAN and restart your

computer (if prompted).

Verifying TCP/IP Properties

1. Click Start, Programs, Accessories and then

Command Prompt.

2. In the Command Prompt window, type “ipconfig”

and then press ENTER. The window displays

information about your IP address, subnet mask

and default gateway.

ENGLISH

Setting up Your Macintosh Computer

Configuring TCP/IP Properties

1. Click the Apple menu, Control Panel and double-click TCP/IP to open the TCP/IP Control Panel.

2. Select Ethernet from the Connect via list.

3. Select Using DHCP Server from the Configure list.

4. Close the TCP/IP Control Panel.

5. Click Save if prompted, to save changes to your configuration.

6. Turn on your OMNI ADSL LAN and restart your computer (if prompted).

Verifying TCP/IP Properties

Check your TCP/IP properties in the TCP/IP Control Panel.

Accessing the OMNI ADSL LAN

Access the OMNI ADSL LAN using the web configurator or the SMT via a telnet session.

Procedure For Web Configurator Configuration

1. Launch your web browser and enter “192.168.1.1” as the URL.

2. Type “admin” as the user name, “1234” (default) as the password and press ENTER.

3. You should now see the SITE MAP screen. Click the help icon (located in the upper right portion all screens)

for online HTML help.

Procedure For SMT Configuration via Telnet

1. Launch a Telnet program. In Windows, click Start and then Run.

2. Type “Telnet” followed by a space and the IP address of the OMNI ADSL LAN, (192.168.1.1 is the default)

and click OK to display the password screen.

3. Enter “1234”, the default password, to access the SMT main menu. As you type a password, the screen

displays an asterisk “ * ” for each character you type.

ENGLISH

Troubleshooting

PROBLEM CORRECTIVE ACTION

The PWR and/or SYS LEDs

are off.

Make sure the OMNI ADSL LAN’s power adapter is connected to the

OMNI ADSL LAN and plugged into an appropriate power source. Check

that the OMNI ADSL LAN and the power source are both turned on.

Turn the OMNI ADSL LAN off and on. If the error persists, you may have a

hardware problem. In this case, you should contact your vendor.

The LAN LED won’t turn on. Check the cable connection to the OMNI ADSL LAN port.

Make sure your computer network card is working properly.

The DSL LED is off. Check the connection between the OMNI ADSL LAN DSL port and the

wall jack.

I cannot access the SMT menu.

The default SMT password is “1234”. If you have changed the password

and have now forgotten it, you will need to reset the OMNI ADSL LAN or

upload the default configuration file (see User’s Guide).

I cannot access the web

configurator.

Check that your computer IP address and the OMNI ADSL LAN IP address

are on the same subnet.

If you changed the OMNI ADSL LAN default LAN IP address then enter the

new one as the URL.

Make sure you enter the correct user name and password. The default

user name is “admin” and the default password is “1234”. If you forgot

your password, you have to reset the OMNI ADSL LAN. See the User’s

Guide.

I cannot ping any computer on

the LAN.

If the 10/100M LAN LED is off, check the cables between the OMNI ADSL

LAN and your computer or switch.

Check the TCP/IP configuration on your computer. Make sure that the IP

address and the subnet mask of the OMNI ADSL LAN and the computers

are on the same subnet.

I cannot access the Internet.

Make sure the OMNI ADSL LAN is turned on and connected to the

network.

If the OMNI ADSL LAN’s DSL LED is off, check the cable between the

OMNI ADSL LAN and the telephone wall jack.

Make sure you entered your user name correctly. Your user name may

be case-sensitive.

Inhaltsverzeichnis

Sprachen:

Andere ZyXEL Communications Modem Handbücher

ZyXEL Communications

ZyXEL Communications U-90E Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications IES-1248-51 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications WAH1004 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications Prestige 642 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications COMET 336 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications VDSL2 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications ONU-634HA Series Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications ONU-2024 Series Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications NWA-3160 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications Prestige 971M Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications Prestige 623ME-T Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications P841C Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications OMNI.NET LITE Handbuch

ZyXEL Communications

ZyXEL Communications P-660R-T1 Handbuch

ZyXEL Communications

ZyXEL Communications Prestige 630 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications Omni 56K II Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications U-336E Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications NBG-419N Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications P-630-S Series Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications WiMAX XOHM Leitfaden

ZyXEL Communications

ZyXEL Communications OMNI 56K Plus Handbuch

ZyXEL Communications

ZyXEL Communications Prestige 841 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications Omni 56K Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications U-90E Bedienungsanleitung

Beliebte Modem Handbücher anderer Marken

Davicom

Davicom DM562AP Bedienungsanleitung

Zte

Zte WiMAX Bedienungsanleitung

Intelimax

Intelimax MA-2060 Bedienungsanleitung

SMC Networks

SMC Networks D3CM1604V Gebrauchs- und Pflegehandbuch

Telstra

Telstra Wi-Fi 4G Advanced Pro X Bedienungsanleitung

Thrane&Thrane

Thrane&Thrane imarsat EXPLORER 300 Bedienungsanleitung

Samsung

Samsung AceLink SAM-335A Bedienungsanleitung

Enfora

Enfora Enabler-G Kurzanleitung zur Einrichtung

iRZ

iRZ ATM2-232 Bedienungsanleitung

Zhone

Zhone 6310 Bedienungsanleitung

Paradyne

Paradyne Hotwire 7976 Bedienungsanleitung

US Robotics

US Robotics 3453C Bedienungsanleitung

MaxTech

MaxTech Plug & Play Internal Voice/FAX/Data/SVD... Bedienungsanleitung

Zte

Zte MF823 Bedienungsanleitung

Four-Faith

Four-Faith F1403 Bedienungsanleitung

Sierra Wireless

Sierra Wireless AIRLINK MP595W Bedienungsanleitung

Gemtek

Gemtek WiMAX WIXFBR-103 Bedienungsanleitung

Zoom

Zoom 1070 Series Bedienungsanleitung