ZyXEL Communications P964 APR 964 Bedienungsanleitung

P964 APR 964

Cable Router with 11g AP

Quick Installation Guide VER. 1.0

Rear Panel Connections

PORT CONNECTION

CABLE Connect the F-type connector to the CATV outlet using a

coaxial cable.

POWER Connect the external power adaptor to the P964 APR and

plug it into an appropriate power outlet.

TO a COMPUTER TO a HUB

LAN1~LAN4 Straight-through/Crossover

Ethernet cable Straight-through/Crossover

Ethernet cable

WLAN IEEE 802.11g/b -

USB USB cable -

Before You Start

The P964 APR is a broadband cable CPE with dual modem/router operation mode. In

order to use your P964 APR, you need to establish an internet access account with your

local cable operator.

1. A cable Internet service that supports two-way cable modem access.

2. A coaxial cable line which has been prepared for cable modem service by your ISP

or cable operator.

3. The P964 APR’s Media Access Control (MAC) address is labeled on the bar code

sticker. The MAC address consists of 12 characters preceded by the text “HFC

MAC:”.

Use the HFC MAC address for registering with your cable operator.

4. The IP address(es) of the Domain Name System server(s) is supplied by your ISP.

5. The P964 APR is configured as a router with NAT and DHCP enabled and with

following factory default.

LAN IP Address 192.168.1.1

Subnet Mask 255.255.255.0

DHCP IP Pool 192.168.1.33 – 192.168.1.64

Web username webadmin

Web password 1234

Note: The default might be different from different cable operators. Please

consult with your cable Internet service provider for any change.

Preparing Your Network

1. Your computer must have a 10M or 100M NIC (Network Interface Card), USB

interface or IEEE 802.11g/11b compatible client.

2. If using USB connection, you have to install the USB driver. Insert the supporting

CD into the CD-ROM drive before you connect the USB port of P964 APR to the

USB port on your computer and power on your P964 APR at the first time. System

may automatically hint you the installation guide for USB driver and specify the

directory where USB driver is stored according to the step-by-step instruction after

the CD-ROM drive is ready to read. The USB driver supports Windows 98SE, ME,

2000 and XP.

TCP/IP should already be installed on computers and configure your computer as a

DHCP client.

The following procedures are for dynamic IP addresses.

Setting up Your Windows 95/98/Me Computer

Installing TCP/IP Components

1. Click Start, Settings, Control Panel and double-click the Network icon.

2. The Network window Configuration tab displays a list of installed components.

To install TCP/IP:

a. In the Network window, click Add.

b. Select Protocol and then click Add.

c. Select Microsoft from the list of manufacturers.

d. Select TCP/IP from the list of network protocols and then click OK.

Configuring TCP/IP

1. In the Network window Configuration tab, select your network adapter’s TCP/IP

entry and click Properties.

2. Click the IP Address tab. Click Obtain an IP address automatically.

3. Click the DNS Configuration tab. Select Disable DNS.

4. Click the Gateway tab. Highlight any installed gateways and click Remove ..

5. Click OK to save and close the TCP/IP Properties window.

6. Click OK to close the Network window.

7. Turn on your P964 APR and restart your computer when prompted. Insert the

Windows CD if prompted.

Verifying TCP/IP Properties

1. Click Start and then Run. In the Run window, type "winipcfg" and then click OK

to open the IP Configuration window.

2. Select your network adapter. You should see your computer's IP address, subnet

mask and default gateway.

Setting up Your Windows NT/2000/XP Computer

Configuring TCP/IP

1. Click Start, Settings, Network and Dial-up Connections and right-click Local

Area Connection or the connection you want to configure and click Properties.

For Windows XP, click start, Control Panel, Network and Internet Connections

and then Network Connections. Right-click the network connection you want to

configure and then click Properties.

2. Select Internet Protocol (TCP/IP) (under the General tab in Win XP) and click

Properties.

3. The Internet Protocol TCP/IP Properties window opens. Click Obtain an IP

address automatically.

4. Click Obtain DNS server automatically.

5. Click Advanced, IP Settings tab and remove any installed gateways, then click

OK.

6. Click OK to save and close the Internet Protocol (TCP/IP) Properties window.

7. Click OK to close the Local Area Connection Properties window.

8. Turn on your P964 APR and restart your computer (if prompted).

Verifying TCP/IP Properties

1. Click Start, Programs, Accessories and then Command Prompt.

2. In the Command Prompt window, type "ipconfig" and then press ENTER. The

window displays information about your IP address, subnet mask and default

gateway.

Setting up Your Macintosh Computer

Configuring TCP/IP Properties

1. Click the Apple menu, Control Panel and double-click TCP/IP to open the

TCP/IP Control Panel.

2. Select Ethernet from the Connect via list.

3. Select Using DHCP Server from the Configure list.

4. Close the TCP/IP Control Panel.

5. Click Save if prompted, to save changes to your configuration.

6. Turn on your P964 APR and restart your computer (if prompted).

Verifying TCP/IP Properties

Check your TCP/IP properties in the TCP/IP Control Panel.

Initialize Your P964 APR

When you plug the power adapter into a wall outlet, the P964 APR is powered on and

executes an automatic installation procedure as described below:

1. Scans and locks on to the service provider’s downstream frequency.

2. Obtains timing, signal, power level, authentication, addressing and other operational

parameters from the CATV CMTS/headend.

3. Downloads its configuration file and is then operational.

During the initialization stage:

1. The POWER LED should be “ON”. The SYS LED lights up after the system

self-test is completed. It stays “ON” when the initialization procedure is completed.

The SYS LED is always YELLOW while system is ready or rebooting. The

SYS LED will become Orange when the system is loading its configuration.

Don’t power off or reset your P964 APR during the SYS LED is becoming

Orange. You can only do so after the SYS LED returns GREEN. Otherwise,

your P964 APR will not work properly anymore.

2. The CABLE LED will be flashing on a 2 seconds on/off cyclic duration while

scanning the downstream channel and then on a 1 second on/off cyclic duration

when it has locked on to a downstream channel and is communicating with the

headend CMTS. Once the cable connection is completed, it will remain “ON”. It

may need 40 seconds from step 1 to step 2.

3. The DATA LED flashes when the cable downstream or cable upstream is receiving

or transmitting data. It is OFF when the cable connection is idle.

4. Depending on which port is connected successfully, the LAN (1~4) LED , WLAN,

or the USB LED will be “ON” and flashing while sending/receiving data to/from

your computer/laptop.

Troubleshooting

Before performing troubleshooting, make sure both the P964 APR’s power (PWR)

LED and the system status (SYS) LED are on.

PROBLEM CORRECTIVE ACTION

The PWR LED

is off. Make sure that the P964 APR’s power adaptor is connected to the

P964 APR and plugged in to an appropriate power source. Check

that the power source is turned on.

If the error persists, you may have a hardware problem. In this

case, you should contact your cable operator.

The SYS LED is

off. Turn the P964 APR’s power off and then on again.

LAN (1~4) LED

WLAN LED and

USB LED are

OFF.

Check the LAN/WLAN/USB LEDs on the front panel. One of

these LEDs should be on. If they are all off, check the Ethernet

cables between your P964 APR and hub/station, or your

802.11g/11b clients, or the USB cable on your station.

Can not access

the Internet. Make sure that the coaxial cable is connected to the P964 APR

and the Internet.

Check with your service provider to see if your account has been

activated.

Check if your computer’s network configuration is correct. For a

dynamic IP address assignment, you have to activate your

computer’s DHCP client. Meanwhile, you may need to assign a

DNS server address. Refer to cable operator’s configuration

information.

Launch “192.168.1.1:8080” in your web browser. Enter “webadmin” as user name and

“1234” as password to log on for more information.

Inhaltsverzeichnis

Andere ZyXEL Communications Netzwerk-Router Handbücher

ZyXEL Communications

ZyXEL Communications Prestige 128L Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications NXC5200 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications VMG8623 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications P-2812HNU-51c Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications P-662H/HW(-I) Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications XG3700 Series Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications NBG318S Series Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications Prestige 100L Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications 660H/HW(-I) Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications 623ME(-I) Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications Prestige 642M series Beilage

ZyXEL Communications

ZyXEL Communications NBG318S Series Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications Nebula NR7101 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications STB-1001S3 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications VMG8324 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications UAG4100 Handbuch

ZyXEL Communications

ZyXEL Communications PES-100 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications Prestige 941 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications Dimension ES-124P Referenzhandbuch

ZyXEL Communications

ZyXEL Communications VES-1616F-44 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications P8802T Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications IES-5000 Series Handbuch

ZyXEL Communications

ZyXEL Communications Prestige 791R Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications VES-1000 Series Bedienungsanleitung

Beliebte Netzwerk-Router Handbücher anderer Marken

Allnet

Allnet ALL0333AU Bedienungsanleitung

HomeSeer

HomeSeer HT-SEL Bedienungsanleitung

Sercomm

Sercomm Genesis OC3505D Bedienungsanleitung

Billion

Billion BIPAC 5102 Series Bedienungsanleitung

TP-Link

TP-Link TD-8817 Bedienungsanleitung

Motorola

Motorola MR1900 Bedienungsanleitung

Digi

Digi IX14 Bedienungsanleitung

Cisco

Cisco NCS 540 Handbuch

XAVi

XAVi X8821e Bedienungsanleitung

BEC

BEC 6200WZL Bedienungsanleitung

MikroTik

MikroTik hAP ac3 Series Bedienungsanleitung

Korenix

Korenix JetNet 5428G Series Bedienungsanleitung

NETGEAR

NETGEAR FS526T - Switch Bedienungsanleitung

Automated Logic

Automated Logic ZN551 Betriebsanleitung

Cisco

Cisco ASR 1000 Series Bedienerhandbuch

EnGenius

EnGenius ESR-9710 Bedienungsanleitung

Cisco

Cisco 805 Series Bedienungs- und Sicherheitshinweise

LevelOne

LevelOne FBR-1416 Bedienungsanleitung