ZyXEL Communications Prestige 650 Bedienungsanleitung

Prestige 650 Read Me First

PORT CONNECTION

DSL Connect to a telephone jack using a telephone wire.

CONSOLE Connect to a serial port (COM port) on your computer using the RS-232 end (the big end) of the console

cable (optional part). Connect the other end to the Prestige CONSOLE port.

LAN 10/100M Connect to a computer using a crossover Ethernet cable or a hub using a straight-through cable.

POWER Connect to a power source using the power adapter for your region (see your User’s Guide).

IP Address 192.168.1.1 Default Password 1234

Subnet Mask 255.255.255.0 DHCP IP Pool (Router

only)

192.168.1.33 – 192.168.1.64

You need an account with an Internet Service Provider (ISP).

1. Your user (account) name and password.

2. VPI (Virtual Path Identifier) and VCI (Virtual Channel Identifier) numbers.

3. Encapsulation: PPP, RFC 1483, ENET ENCAP or PPPoE.

4. Multiplexing method: LLC-based or VC-based.

5. You may need to know your Service Name if you are using PPPoE.

6. The IP address of the DNS (Domain Name System) server(s) and Gateway (if provided).

All computers must have a 10M or 100M Ethernet adapter card and TCP/IP installed.

TCP/IP should already be installed on computers using Windows NT/2000/XP, Macintosh OS 7 and later operating systems.

These procedures are for dynamic IP addresses.

Setting up Your Windows 95/98/Me Computer

Installing TCP/IP Components

1. Click Start,Settings, Control Panel and double-click the Network icon.

2. The Network window Configuration tab displays a list of installed components.

To install TCP/IP:

a. In the Network window, click Add.

b. Select Protocol and then click Add.

c. Select Microsoft from the list of manufacturers.

d. Select TCP/IP from the list of network protocols and then click OK.

Configuring TCP/IP

1. In the Network window Configuration tab, select your network adapter’s TCP/IP entry and click Properties.

2. Click the IP Address tab. Click Obtain an IP address automatically.

3. Click the DNS Configuration tab. Select Disable DNS.

4. Click the Gateway tab. Highlight any installed gateways and click Remove until there are none listed.

5. Click OK to save and close the TCP/IP Properties window.

6. Click OK to close the Network window.

7. Turn on your Prestige and restart your computer when prompted. Insert the Windows CD if prompted.

Verifying TCP/IP Properties

1. Click Start and then Run. In the Run window, type "winipcfg" and then click OK to open the IP Configuration

window.

2. Select your network adapter. You should see your computer's IP address, subnet mask and default gateway.

Setting up Your Windows NT/2000/XP Computer

Configuring TCP/IP

1. Click Start, Settings, Network and Dial-up Connections and right-click Local Area Connection or the connection you

want to configure and click Properties. For Windows XP, click start, Control Panel, Network and Internet

Connections and then Network Connections. Right-click the network connection you want to configure and then click

Properties.

2. Select Internet Protocol (TCP/IP) (under the General tab in Win XP) and click Properties.

3. The Internet Protocol TCP/IP Properties window opens. Click Obtain an IP address automatically.

4. Click Obtain DNS server automatically.

5. Click Advanced, IP Settings tab and remove any installed gateways, then click OK.

6. Click OK to save and close the Internet Protocol (TCP/IP) Properties window.

7. Click OK to close the Local Area Connection Properties window.

8. Turn on your Prestige and restart your computer (if prompted).

Verifying TCP/IP Properties

1. Click Start, Programs, Accessories and then Command Prompt.

2. In the Command Prompt window, type "ipconfig" and then press ENTER. The window displays information about

your IP address, subnet mask and default gateway.

Setting up Your Macintosh Computer

Configuring TCP/IP Properties

1. Click the Apple menu, Control Panel and double-click TCP/IP to open the TCP/IP Control Panel.

2. Select Ethernet from the Connect via list.

3. Select Using DHCP Server from the Configure list.

4. Close the TCP/IP Control Panel.

5. Click Save if prompted, to save changes to your configuration.

6. Turn on your Prestige and restart your computer (if prompted).

Verifying TCP/IP Properties

Check your TCP/IP properties in the TCP/IP Control Panel.

1. Web configurator

2. SMT (System Management Terminal). Access the SMT via:

• Telnet • Console port using terminal emulation software

Procedure For Web Configurator Configuration

1. Launch your web browser and enter “192.168.1.1” as the URL.

2. Type “admin” as the user name, "1234" (default) as the password and press ENTER.

3. You should now see the SITE MAP screen. Click the help icon (located in the upper right portion all screens) for online

HTML help.

Procedure For SMT Configuration via Telnet

1. Launch a Telnet program. In Windows, click Start and then Run. Type “Telnet” followed by a space and the IP address

of the Prestige, (192.168.1.1 is the default) and click OK to display the password screen.

2. Enter the password (1234 is the default), to access the SMT main menu. As you type a password, the screen displays an

“*”for each character you type.

Procedure For SMT Configuration via Console Port

1. Configure a terminal emulation communications program as follows: VT100 terminal emulation, no parity, 8 data bits, 1

stop bit, data flow set to none, 9600 bps port speed.

2. Press ENTER to display the SMT password screen. The default password is “1234”.

Use the ISP information you gathered to configure SMT menu 4 and access the Internet. Refer to your User’s Guide for

details.

PROBLEM CORRECTIVE ACTION

The PWR and/or SYS LED

are off.

Make sure the Prestige is connected to the correct power adapter, the power adapter is

plugged into an adequate power supply and the Prestige power switch is turned on.

Turn the Prestige off and on. If the error persists, you may have a hardware problem. In this

case, you should contact your vendor.

The LAN LED won’t turn on. Check the cable connection to the Prestige LAN port.

Make sure you are using a crossover Ethernet cable if you are connecting the Prestige

directly to one computer and a straight-through cable if you are connecting your Prestige to

LAN computers via a hub.

Make sure your computer NIC (Network Interface Card) is working properly.

The DSL LED is off. Check the connection between the Prestige DSL port and the wall jack.

Check to see if the Prestige is connected to your computer’s serial port.I cannot access the Prestige

via the console port. Check to see if the communications program is configured correctly. Refer to the defaults in

the Procedure For SMT Configuration via Console Port section.

I cannot access the SMT

menu.

The default SMT password is “1234”. If you have changed the password and have now

forgotten it, you will need to upload the default configuration file (see User’s Guide).

I cannot access the web

configurator.

Check that your computer IP address and the Prestige IP address are on the same subnet.

If you changed the Prestige default LAN IP address then enter the new one as the URL.

Remove any filters you have applied in menu 3.1 (LAN) or in menu 11.5 (WAN) to block web

service.

PROBLEM CORRECTIVE ACTION

Check if you have an SMT console session running.

I cannot ping any computer on

the LAN.(Router only)

If all of the 10/100M LAN LEDs are off, check the cables between the Prestige and your

computer or hub.

Verify that the IP address and the subnet mask of the Prestige and the computers are on the

same subnet.

Check the TCP/IP configuration on your computer. Make sure that the IP address and the

subnet mask of the Prestige and the computers are on the same subnet.

I cannot get a WAN IP

address from the ISP.

The WAN IP is provided after the ISP verifies the MAC address, host name or user ID.

Find out the verification method used by your ISP and configure the corresponding fields.

I cannot access the Prestige

web configurator.

Check if you have applied a filter in menu 3.1 (LAN) or in menu 11.5 (WAN) to block web

service.

Check if you have an SMT console session running.

Check the TCP/IP configuration on your computer. Make sure that the IP address and the

subnet mask of the Prestige and the computers are on the same subnet.

The default password is “1234”. If you have changed the password and have now forgotten

it, you will need to upload the default configuration file (see User’s Guide).

I cannot access the Internet. Make sure the Prestige is turned on and connected to the network.

If the Prestige’s DSL LED is off, check the cable between the Prestige and the telephone wall

jack.

Check whether your cable/xDSL device requires a crossover or straight-through cable.

Make sure you entered your user name correctly. A username may be case-sensitive.

Andere Handbücher für Prestige 650

Inhaltsverzeichnis

Andere ZyXEL Communications Netzwerk-Router Handbücher

ZyXEL Communications

ZyXEL Communications X650 Handbuch

ZyXEL Communications

ZyXEL Communications WSQ50 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications ES-2108 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications LTE3301-PLUS Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications VMG8924-B10A Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications VES-1012 - Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications IES-1000 - ANNEXE 7 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications VMG1312 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications NBG6716 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications VMG Series Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications Prestige 652 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications EXTRASMART ES-1528 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications VES-1000 Series Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications LTE7460-M608 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications ADSL VoIP IAD with 802.11g Wireless 2602HW... Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications GS1510-16 - Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications NBG-419N v2 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications ES-2108 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications Armor Z1 NBG6816 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications G-570U Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications Prestige 100IH Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications P-2802HW(L)-IX Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications Prestige 941 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications Dimension ES-124P Referenzhandbuch

Beliebte Netzwerk-Router Handbücher anderer Marken

Allnet

Allnet ALL0333AU Bedienungsanleitung

HomeSeer

HomeSeer HT-SEL Bedienungsanleitung

Sercomm

Sercomm Genesis OC3505D Bedienungsanleitung

Billion

Billion BIPAC 5102 Series Bedienungsanleitung

TP-Link

TP-Link TD-8817 Bedienungsanleitung

Motorola

Motorola MR1900 Bedienungsanleitung

Digi

Digi IX14 Bedienungsanleitung

Cisco

Cisco NCS 540 Handbuch

XAVi

XAVi X8821e Bedienungsanleitung

BEC

BEC 6200WZL Bedienungsanleitung

MikroTik

MikroTik hAP ac3 Series Bedienungsanleitung

Korenix

Korenix JetNet 5428G Series Bedienungsanleitung

NETGEAR

NETGEAR FS526T - Switch Bedienungsanleitung

Korenix

Korenix JetNet 5710G Series Bedienungsanleitung

Automated Logic

Automated Logic ZN551 Betriebsanleitung

Cisco

Cisco ASR 1000 Series Bedienerhandbuch

EnGenius

EnGenius ESR-9710 Bedienungsanleitung

Cisco

Cisco 805 Series Bedienungs- und Sicherheitshinweise