ZyXEL Communications X6004 Bedienungsanleitung

X6004

IP PBX

Quick Start Guide

Version 1.00

9/2007

Edition 1

DEFAULT LOGIN

LAN IP Address https://192.168.1.12

WAN IP Address https://172.16.1.1

User Name admin

Password 1234

CONTENTS

ENGLISH 2

DEUTSCH 24

ESPAÑOL 48

FRANÇAIS 70

ITALIANO 92

繁體中文 116

简体中文 137

ENGLISH

Introduction

An IP PBX is a telephone exchange device located at your company which sets up and

controls calls. This document covers configuring the X6004 for internal calls and outbound

calls to either the PSTN (Public Switched Telephone Network) or your ITSP (Internet

Telephony Service Provider).

This Quick Start Guide consists of the following sections:

Hardware

- page 3

1Installation

2Extension Slots - install a hard drive and voice interface cards for

connecting analog phones and direct connections to the PSTN or a

traditional PBX.

3Hardware Connections.

Configuration

- page 8

4Web Configurator Login

5Network Setup Wizard

6Setting up Extensions - create an authority group and create

extensions for internal communications. An authority group manages

telephone extensions.

7Create an Outbound Rule - create outbound rules and associate an

authority group to them. These rules specify which outbound trunk should

be used for outgoing calls.

8Outbound Groups (External Links) - configure the external links used

in outbound rules.

9IP Phone Registration and Making Calls - register IP phones and make

telephone calls.

PSTN

Internet

ITSP

ENGLISH

"See the User’s Guide on the included CD for information on all features of

the X6004.

1 Installation

The X6004 can be rack-mounted or installed on a desktop.

"For proper ventilation, allow at least 4 inches (10 cm) of clearance at

the front and 3.4 inches (8 cm) at the back of the IP PBX. Leave space

between X6004s if stacking.

1.1 Desktop Installation

1Set the X6004 on a smooth, level surface.

2If your X6004 comes with unattached rubber feet, attach them to each corner on the

bottom of the X6004.

ENGLISH

1.2 Rack-mounted Installation

1Align one bracket with the holes on one side of the X6004 and secure it with bracket

screws smaller than the rack-mounting screws. Similarly, attach the other bracket.

2After attaching both mounting brackets, position the X6004 in the rack by lining up the

holes in the brackets with the appropriate holes on the rack. Secure the X6004 to the

rack with the rack-mounting screws.

2 Extension Slots

This section shows you how to install a hard drive as well as the FXS and FXO interface

cards in the X6004.

FXO

FXS

PSTN

ENGLISH

FXS Interface Cards - The FXS interface cards connect analog phones to the X6004. The

FXS interface cards provide line voltage.

"NEVER connect your FXS ports to your PSTN line. This may damage your

interface card as well as the X6004.

FXO Interface Cards - The FXO interface cards connect to the PSTN or a traditional

PBX. FXO ports always point in the direction of the telephone company’s services.

2.1 Interface Card and Hard Drive Installation

See the User’s Guide for supported interface cards and hard drive specifications. In this

example, the hard drive and the interface card are referred to as expansion modules.

"Make sure the X6004 is turned off when installing or removing a hard drive

or extension cards.

"Ground yourself (by properly using an anti-static wrist strap for example)

whenever working with the device’s hardware or connections.

1Use a Phillips screwdriver to unscrew the thumbscrews and remove the protective

cover from the slot.

2Store the cover in a safe place in case you want to use it in the future.

ENGLISH

"Only the interface card is shown.

3Insert the expansion module by lining it up with the grooves inside the extension slot

and sliding it in.

4Push the expansion module into the extension slot. The expansion module front should

be flush with the front panel of the X6004.

5Use a Phillips screwdriver to securely tighten the thumbscrews in place.

ENGLISH

3 Hardware Connections.

1Use an Ethernet cable to connect the WAN port to your network. It is recommended to

connect the X6004 to a DMZ interface of your Internet security router.

2Use an Ethernet cable to connect the X6004 LAN port to your LAN.

"Inspect the labels on the FXS and FXO cards before making your analog

phone and PSTN connections. NEVER connect your FXS ports to your

PSTN line. This may damage the interface card as well as the X6004.

3Use telephone cables with RJ-11 connectors to connect analog phones to the FXS

interface card on the X6004.

4Use telephone cables with RJ-11 connectors to connect your existing PSTN (Public

Switched Telephone Network) outlet to the FXO interface card on the X6004.

5Connect one end of the supplied power cable or power adaptor to the power receptacle

on the X6004 and the other end to the appropriate power source.

3.1 LEDs

The PWR LED turns on and stays on when the X6004 is receiving power.

The SYS LED blinks during boot up and stays on when the X6004 is ready.

WAN LAN

FXS

FXO

ITSP

PSTN

FXO

FXS

DMZ

ENGLISH

"Boot up takes several minutes. You must wait until the SYS LED stops

blinking and is shining steadily before proceeding.

The WAN and LAN LEDs turn on when the ports detect an Ethernet connection (green =

10 Mbps, orange = 100 Mbps). They blink when data is being transmitted.

The SYS LED on an extension card turns on when the IP PBX detects that the card is

properly installed.

4 Web Configurator Login

You can use the LAN or the WAN port to connect to the X6004.

"Use Internet Explorer 6.0 or higher and ensure that you allow Javascript

and ActiveX to execute on Internet Explorer. (See the appendices in the

user’s guide for details.)

1Log in to the web configurator using HTTPS. If you are

connecting through the LAN port, go to https://

192.168.1.12 (default LAN IP address) or https://

172.16.1.1 (default WAN IP address).

"Click Yes in any security screens that pop-up during the login process.

ENGLISH

2Enter the default administrator

username (admin) and password

(1234) and click Login.

3You are prompted to change the

administrator username and

password. Change your login

credentials, write down the new

password and put it in a safe place.

Click Apply to proceed to the Network

Setup Wizard.

ENGLISH

5 Network Setup Wizard

The wizard opens automatically the first time you log in.

"When using the wizard, click the Next button to proceed to the next screen

or click the Back button to return to the previous screen.

1Configure the WAN settings for the

X6004 as provided to you by your

ISP or network administrator. The

WAN interface serves as a gateway

to your ITSP and peer IP PBX as well

as a SIP server address for remote

IP phones connecting to the X6004.

This screen changes depending on the

encapsulation.

2Configure the LAN IP address and

subnet mask of the X6004.

Andere Handbücher für X6004

Inhaltsverzeichnis

Sprachen:

Andere ZyXEL Communications Telefonanlage Handbücher

ZyXEL Communications

ZyXEL Communications X2002 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications X2002 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications X6004 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications IP PBX X6004 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications X6004 Bedienungsanleitung

Beliebte Telefonanlage Handbücher anderer Marken

Allo.com

Allo.com Nano 2 Bedienungsanleitung

ZYCOD

ZYCOD ZX50 Bedienungsanleitung

Panasonic

Panasonic KX-TDA100BX Bedienungsanleitung

LV switch

LV switch IPPBX800 Gebrauchsanweisung

Edge-Core

Edge-Core VST3305 Bedienungsanleitung

Panasonic

Panasonic KX-T7625 - Digital Proprietary Speakerphone 24... Bedienungsanleitung

Rauland-Borg

Rauland-Borg Telecenter IV Bedienungsanleitung

Grandstream Networks

Grandstream Networks UCM6208 Bedienungsanleitung

ATCOM

ATCOM IPPBX IP02 Bedienungsanleitung

Panasonic

Panasonic KX-TVS50 - 2 Port Voicemail System Bedienungsanleitung

bintec elmeg

bintec elmeg elmeg hybird 600 Bedienungsanleitung

Panasonic

Panasonic KX-NS300 Bedienungsanleitung

MCK

MCK EXTender PBXgateway Bedienungsanleitung

Panasonic

Panasonic KX-NS300CN Betriebsanleitung

NEC

NEC SL1000 Bedienungsanleitung

Epygi

Epygi Quadro Quadro 2xi Bedienungsanleitung

SMC Networks

SMC Networks TigerVoIP SMCPBX10 Bedienungsanleitung

AGFEO

AGFEO AC 14 analog Bedienungsanleitung