ZyXEL Communications ZyAIR G-5100 Bedienungsanleitung

ZyAIR G-5100

Outdoor 802.11g Business Access Point/Bridge/Repeater

Quick Start Guide

Version 3.50

2/2005

ZyAIR G-5100

Overview

This Quick Start Guide shows how to set up and configure the ZyAIR to allow wireless clients to access your

wired network. See your User’s Guide for background information on all features.

1Unpacking the ZyAIR

2Hardware Connections

3Initial Configuration

4Hardware Installation

5Troubleshooting

1 Unpacking the ZyAIR

Leave the ZyAIR’s shipping box intact and sheltered until arrival at the installation site. If the shipping

container shows signs of damage, immediately notify the transportation company. Upon receipt, inspect

contents to make sure that there are no missing or damaged parts.

Retain all the packing materials (including all internal boxes). In the unlikely event that the equipment must be

returned, use the original packing materials for return shipment. The packing materials are also recommended

for transporting the equipment from location to location.

1.1 Packaging Specifications

ZyAIR G-5100

2 Hardware Connections

Accessories Specification/Description Quantity

Inline Power Injector (PoE) Input 100 ~ 240VAC 50/60Hz, Output 800mA at -48VDC 1

Wall-plug AC Power Cord (1.8m) 1

RS232 Console Cable MIL-C-5015 STP (Shielded Twisted Pair) (2.0m) 1

Uplink Ethernet Cable MIL-C-5015 UTP (Unshielded Twisted Pair) (1.8m) 1

Grounding Cable UL1015 (3.0m) 1

RJ45 Ethernet Cable MIL-C-5015 STP (30.0m) 1

Antennas 5dBi omni-direction rubber antenna 2

Waterproofing Strip 2

Mounting Brackets Wall mount brackets, Mast mount brackets 1 pair, 1 pair

Spanner Installation tool 1

CD-ROM Quick Start Guide and User’s Guide 1

Configure and test the ZyAIR

before installing it in a hard-

to-reach location. Use the

following steps to connect the

ZyAIR.

ZyAIR G-5100

1Use the included spanner

(installation tool) to

connect the ground cable

to the ZyAIR’s frame

ground (as shown).

Connect the other end of

the ground cable to an

appropriate grounding

system.

2Remove the backing from

both sides of the

waterproofing strip.

3Stretch the waterproofing

strip.

4Wrap the waterproofing

strip around the base of

the antenna connector.

5Screw the supplied

antennas clockwise onto

the antenna connectors on

the top and bottom of your

ZyAIR.

Note: Do not over-tighten

the antennas.

ZyAIR G-5100

6Optional: Use the MIL-C-

5015 style RS-232

console cable to connect

the special serial port to a

computer running a

terminal emulation

program.

7Use a power cord to

connect the inline power

injector’s power socket to

an AC power source. The

POWER LED on the front

of the inline power injector

turns on.

8For initial configuration,

use a cross-over Ethernet

cable to connect the inline

power injector’s DATA IN

port to a computer.

Note: After initial

configuration, use a

straight-through

Ethernet cable to

connect the inline

power injector’s

DATA IN port to a

LAN connection

(such as to a switch

or router).

ZyAIR G-5100

3 Initial Configuration

Use Internet Explorer 6.0 and later or Netscape Navigator 7.0 and later versions with JavaScript enabled.

Note: Even though you can connect to the ZyAIR wirelessly, it is recommended that you connect your

computer to the DATA IN port for initial configuration.

9Connect the MIL-C-5015

style Ethernet connector

to the special Ethernet

port on the bottom of the

ZyAIR.

Connect the RJ-45

Ethernet connector (the

other end of the special

Ethernet cable) to the

POWER & DATA OUT

port on the front of the

inline power injector.

Note: The ZyAIR starts. The ACTIVE LED on the front of the inline power injector turns on.

1Launch your web browser. Enter 192.168.1.2 (the

ZyAIR’s default IP address) as the address.

If the login screen does not display, see Section

5.1 on page 14 to set your computer’s IP address.

2Click Login (the default password 1234 is already

entered).

ZyAIR G-5100

5Click WIZARD SETUP in the MAIN MENU screen.

3.1 Wizard Setup

Use the setup wizard to configure your ZyAIR for wireless stations to access your wired LAN.

Note: Click Next in each screen to continue or click Back to return to the previous screen.

3Change the login password by entering a new

password and clicking Apply.

4Click Apply to replace the ZyAIR’s default digital

certificate.

ZyAIR G-5100

Your settings are not saved when you click Back.

1This screen is optional. You can just click Next.

2Use the second wizard screen to set up the wireless LAN.

Note: The wireless stations and ZyAIR must use the same ESSID, channel ID and WEP encryption key

(if WEP is enabled) for wireless communication.

System Name is for identifying the

ZyAIR. You can enter your computer's

"Computer Name".

Domain Name: Enter a domain name if

your ISP requires one for

authentication; otherwise you can leave

it blank or set to whatever may have

displayed automatically.

The ZyAIR has two WLAN adapters.

Select one to configure.

Enter a descriptive name to identify the

ZyAIR in the wireless LAN.

Click Scan to have the ZyAIR

automatically select a channel and

display it in the Channel ID field.

Select 64-bit or 128-bit to encrypt data

frames before transmitting them over

the wireless network.

Select Disable to turn off WEP data

encryption.

Select ASCII or HEX WEP key input

method and then follow the on-screen

instructions to set up the WEP keys.

Click Next to continue.

ZyAIR G-5100

3Fill in the fields in the last wizard configuration screen.

7Change the wireless parameter settings in the wireless stations to match those of the ZyAIR. Refer to your

wireless adapter’s documentation

If you have an IP address to use, select

Use fixed IP address and enter it

along with the subnet mask and

gateway IP address.

Click Finish.

Note: If you change the ZyAIR’s IP

address, you must use the

new IP address if you want

to access the web

configurator again.

4Click Ok.5Click Yes if you do not want to configure advanced

features, otherwise click No.

6This final wizard screen displays if you clicked No.

You may return to the MAIN MENU and continue

to configure your ZyAIR.

ZyAIR G-5100

4 Hardware Installation

In general, the best location for the access point is at the center of your intended wireless coverage area. It is

recommended that you do the initial configuration of the ZyAIR prior to mounting.

The ZyAIR can be mounted on the side of a building or mounted to an antenna mast as described:

A wall (side) mount allows for mounting an antenna (mast) on the side of a building or on the side of an

elevated penthouse. This will provide a convenient mounting location when the roof overhang is not excessive

and/or the location is high enough to provide a clear line of sight.

An antenna couples RF signals onto air. A transmitter within a wireless device sends an RF signal to the

antenna, which propagates the signal through the air. The antenna also operates in reverse by capturing RF

signals from the air.

Choosing the right antennas and positioning them properly increases the range and coverage area of a

wireless LAN.

In most situations mounting an antenna directly to the wall will not allow you to properly align the antenna with

the corresponding antenna at the opposite end of your wireless link. As poor alignment will typically result in

poor performance, it is advised that you mount the ZyAIR to a mast.

4.1 Antenna Mast/Antenna Requirements

To accommodate the ZyAIR, the mast must satisfy the following requirements:

• The construction of the mast must be of a sturdy, weatherproof and non-corrosive material, for example, galva-

nized or stainless steel construction pipe.

• Typical diameter of the mast should be between 35 mm (1.4”) and 41 mm (1.625”). Subject to the type of mast

that you intend to install, other diameters are possible.

• The height of the antenna mast must be sufficient to allow the antenna to be installed at least 1.5 m (5’) above

the peak of the roof. If the roof is metal, then the height of the antenna should be a minimum of 3m (10’) above

the roof.

• The mast or wall-bracket must be free from any substance that may prevent a good electrical connection with

the antenna, for example, paint.

4.2 Grounding

A safe grounding system is necessary to protect your outdoor installation from lightning strikes and the build-

up of static electricity.

Direct grounding of the antenna mast, ZyAIR and surge arrester are very important. The ZyAIR has a built in

surge arrester. The ZyAIR’s frame ground (see Section 3 on page 2) should be connected to the same

grounding system as the antenna mast and the AC wall outlet.

Andere Handbücher für ZyAIR G-5100

Inhaltsverzeichnis

Andere ZyXEL Communications Drahtloser Zugangspunkt Handbücher

ZyXEL Communications

ZyXEL Communications NWA-3166 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications NWA3000-N Series Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications NWA5121-N Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications NWA1123-AC Pro Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications ZYAIR G-1000 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications 802.11a/g Wireless CardBus Card ZyXEL AG-120 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications NWA3550-N - Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications ZyAIR Wireless Gateway Series Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications NWA1123 NI Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications ZyXEL ZyAIR B-1000 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications NWA1100N-CE CloudEnabled Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications NWA1120 Series Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications NWA5301-NJ Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications FMT3251 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications NWA50AX Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications LTE3311 series Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications 100-NH Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications ZyXEL ZyAIR B-3000 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications P-2612HW Series Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications EMG5523-T50B Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications Wireless Access Point ZyAIR B-500 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications NWA-8500 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications NWA-3500 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications NWA-3160 Bedienungsanleitung

Beliebte Drahtloser Zugangspunkt Handbücher anderer Marken

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Bedienungsanleitung

Ubiquiti

Ubiquiti NanoStation NSM2 Bedienungsanleitung

Cisco

Cisco Aironet 1550 Series Bedienungsanleitung

Aruba

Aruba IAP-335 Bedienungsanleitung

Advantek Networks

Advantek Networks AWN-AP-54MR Bedienungsanleitung

IP-COM

IP-COM AP355 Bedienungsanleitung

Buffalo

Buffalo AirStation WLA-L11G Bedienungsanleitung

EnGenius

EnGenius EnStationACv2 Bedienungsanleitung

D-Link

D-Link DAP-3662 Bedienungsanleitung

Widelink

Widelink ezWave WAP-1100 Series Bedienungsanleitung

Edimax

Edimax CAP1200 Bedienungsanleitung

xG Technology

xG Technology xMax CN1300 Bedienungsanleitung

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Bedienungsanleitung

Aruba

Aruba AP-203R Bedienungsanleitung

LuXout Shades

LuXout Shades LUXSHADE MOTION Bedienungsanleitung

CreatComm

CreatComm TB5F Bedienungsanleitung

SineDigital

SineDigital MW-1500AP(H) Bedienungsanleitung

TP-Link

TP-Link AP9650 V1 Bedienungsanleitung