ZyXEL Communications P-660HW-T1 V2 Bedienungsanleitung

ZyXEL Confidential

1/34

ZyXEL

Firmware Release Note

P-660HW-T1 v2

Standard Version

Release 3.40(APR.3)C0

Date:

August 6, 2008

Author:

Jasmine Wang

ZyXEL Confidential

2/34

ZyXEL P-660HW-T1 v2 Standard Version

Release 3.40(APR.3)C0

Release Note

Date: August 6, 2008

Supported Platforms:

ZyXEL P-660HW-T1 v2

Versions:

ZyNOS Version : V3.40(APR.3) | 08/06/2008 13:50:00

Bootbase Version : V1.05 | 03/07/2008 13:32:34

Notes:

The P-660HW-T1 v2, is 4th generation of ZyXEL ADSL product family. It is a high

performance ADSL/ADSL2/ADSL2+ router for small/medium office to have Internet

access and LAN-to-LAN application over the existing copper line. P-660HW-T1 v2 takes

advantage of much higher data rate than ADSL, speed up to 12Mbps (ADSL2) or 24Mbps

(ADSL2+), greater reach, faster start-up, advanced diagnostics and better power

management. This high performance ADSL router is a high integrated advanced Firewall,

Bandwidth Management and IEEE 802.11g wireless features to meet the demand of

high-end market.

P-660HW-T1 v2 provides an embedded mini-PCI module for 802.11g Wireless LAN

connectivity, four single auto-sensing, auto-detection 10/100BASE-T Ethernet ports for

connection to the user’s local network, and a single RJ-11/RJ-45 port for connection to

ADSL/ADSL2/ADSL2+ line.

1. Support Multiboot client V2.3

2. Support ADSL2+ by TrendChip modem code 3.10.9.0

Known Issues:

1．Set ATM QoS Type= VBR, Peak Cell Rate (PCR) =1000, Sustain Cell Rate (SCR) =

500, Maximum Burst Size (MBS) = 500, Test result it is not steady

2．Step1: set remote node 1 ATM QoS Type= VBR_RT, Step2: set remote node 2 ATM

QoS Type= VBR_nRT, Step3: set remote node 3 ATM QoS Type= CBR, Then the

priority remote node 1>remote node 3>remote node 2, (use one node with CBR and

two nodes with VBR_RT and VBR_nRT in any remote node will case priority

confusedly)

3．When set multi PVCs and to get Dynamic IP, the TriplePlay and IPRP function doesn’t

work properly

4．When DUT is power on and link up, if there are many multicast packets on the wan

sides, the DUT will reboot sometimes.

5．IOP issue with Intel 2200BG at WPA2 and WPA2-PSK Mixed mode.

ZyXEL Confidential

3/34

6．Content filter show wrong warning message is caused by Kaspersky Anti-Virus

7．Remote F/W uploading failure under 256/256kbps line rate sometimes.

8．Enable triple play and igmp snooping, and turn on “ip mcast 0” to do IPTV both in lan

and wlan at the same time, device will crash sometimes when disable igmp snooping,

the probability is 60~70%

9．Enable triple play and igmp snooping, and turn on “ip mcast 0” to do IPTV both in lan

and wlan at the same time, when set IPTV application to group 3 (or group 4…), the

IPTV can’t broadcast.

Features:

Modification in 3.40(APR.3)C0 | 08/06/2008

1. Change to FCS

Modification in V3.40(APR.3)b4 | 08/04/2008

1. [BUG MERGE]

Symptom: End user try to change debug flag by console, then they could upgrade other

product firmware and change DUT’s MAC.

They can use command atse to get seed esaily.

Condition: N/A

Modification in V3.40(APR.3)b3 | 07/24/2008

1. [BUG MERGE]

SPRID: 080707304

Symptom: Enable WDS, then reboot device, it will crash continously .

Condition:

Step1: Setup a WDS connecion with CI command: wlan wds set ＜index＞＜Mac＞

Step2: enable this connection with CI command: wlan wds enable x 1

Step3: reboot device, it will crash continously.

2. [BUG MERGE]

SPRID: 080703152

Symptom: INTERNAL ERROR when apply log setting

Condition:

1:Select some items in Web interface -＞Advanced Mode -＞Maintenance -＞Logs -

＞Log Settings and apply

2:Select all the items and apply.

An internal error will be shown after applying the settings. Please see in attached

document.

3. [BUG MERGE]

SPRID: 080703153

Symptom: PASSWORD/ACCESS TO WEB INTERFACE (Internet Explorer)

Condition:

Actual password : 0987

(1)Case A :

ZyXEL Confidential

4/34

- start a browser

- go to web interface (default : 192.168.1.1)

- click Login (no change to password)

- The users enters in the Status mode

No modifications possible

(2)Case B :

- start a browser

- go to web interface (default : 192.168.1.1)

- Enter 9999 as password

- click Login

- The users enters in the Status mode

No modifications are possible

No message about wrong password

(3)Case C :

- start a browser

- go to web interface (default : 192.168.1.1)

- click Login (no change to password)

- The users enters in the Status mode

- Click Logout

- Enter 9999 as password

- Click Login

- Loops within the authentication page (rpAuth.html)

In this case, it’s not possible to enter the Status mode

4. [BUG MERGE]

SPRID: 080703154

Symptom: Wlan scan by telnet cause device crash.

Condition:

Step1:reset device to factory default

Step2:connect a PC to lan port of device

Step3:telnet 192.168.1.1 in run utility in PC.

Step4:issue command” wlan scan”

Notice:Crash happens when some AP around hide SSID

5. [BUG MERGE]

SPRID: 080708339

Symptom: If turn on “ip mcast 0” to do IPTV both in lan and wlan at the same time, the

CPU loading will be 100%.

Condition:

Step1. Default romfile.

Step2. Configure two PVC, PVC1:PPPoE Router to Internet and IPTV VoD,

PVC2:RFC1483 bridge for IPTV multicast. Triple Play disabled.

Step3: Open 5~6 channels in IPTV server, STB in LAN plays IPTV only, CPU loading

ZyXEL Confidential

5/34

is about 30%

Step4. CLI”ip mcast 0”to forward multicast packet to WLAN.

Step5. WLAN and LAN play IPTV at the same time, CPU loading will reach to 100%.

(DUT downstream sync rate 24M, VoD 4M, IPTV 5M) You can’t access Internet

web service at this time.

Notice：When the IPTV file is larger, the issue can be reproduced more easily

6. [FEATURE ENHANCE]

Symptom: IGMP snooping for FPT v1.0

7. [BUG MERGE]

SPRID: 080708340

Symptom: If LAN run IPTV and wlan run IPTV or VOD for about 3 ~4 hours, the

wireless will has problem, it can’t send any packets to wireless client and wireless

client can’t get ip from CPE anymore.(you can say wireless is down), only reboot CPE,

wireless can recover then .

Condition:

Step1. Default romfile.

Step2. Configure 2 PVCs, PVC1 to PPPoE for Internet and VOD service; PVc2 for

IPTV only. triple play is disabled. configure wireless LAN to open mode. DSL sync

rate is 24M.

Step3. STB connect with LAN port play IPTV(5M), wireless LAN play IPTV(5M) or

VOD(4M)

Step4. About 3~4 hours later, it can’t send any packets to wireless client and wireless

client can’t get ip from CPE anymore.

Step5. Reboot DUT. wireless can be recovered.

8. [BUG MERGE]

SPRID: 080709448

Symptom: ping packets with size of more than 1472 bytes do not work when triple

play is enable

Condition:

topology:LAN PC---DUT---DSLAM---Switch---Router---Webserver.

ping packets with size of more than 1472 bytes do not work.(triple play enable)

9. [BUG MERGE]

SPRID: 080709469

Symptom: Leave PVC1 with incorrect VPI/VCI, after you configure PVC2-8, VC

Hunt will hunt the VC Hunt table again.

Condition:

Step1:Default romfile.

Step2:Active VC Hunt. Don’t fill in correct vpi/vci in VC Hunt table, after finish the

VC Hunt, the state still active.

Step3:configure PVC2-8 get to internet with Route encapsulation. VC Hunt will start

hunting the VC Hunt table again.

ZyXEL Confidential

6/34

10. [BUG MERGE]

SPRID: 080709479

Symptom: Spelling mistake in GUI

Condition:

No spaces between the link and the word after it (in this case “Firewall”)

11. [BUG MERGE]

SPRID: 080709493

Symptom: Bandwidth MGMT can’t work correctly in Priority mode, and it works like

still in Fairness mode.

Condition:

step1, Enabe Bandwidth MGMT for LAN interface with priority-based mode, allocate

the interface with 3000kpbsstep2. Add two rules for LAN interface, one is www

service with high priority(1000kbps), another is FTP service with low

priority(1000kbps). Step3. Use Chariot software to run ftpget.script for the two rules

that added in step2After step3, from monitor menu, you can see the two rules be

allocated with the same bandwidth but not according to the high priority with more

bandwith rules

12. [BUG MERGE]

SPRID: 080709535

Symptom: The wireless bitrate would larger then 11M/s sometimes even fix the mode

as 802.11B

Condition:

Step1. wireless client connect to device with 802.11G mode

Step2. change device wireless 802.11 mode to 802.11B only.You can found the bitrate

would large than 11M/s until re-associate.

13. [BUG MERGE]

SPRID: 080707305

Symptom: If content filter act, suppose ’wwww.google.com’ is a blocked site, if you

try to access it in IE7.0, there will be some illegal character.

Condition:

If content filter act, suppose ’wwww.google.com’ is a blocked site, if you try to access

it in IE7.0, there will be some illegal character

14. [BUG MERGE]

Symptom: Airoha frequency shift issue.

Condition:

Carrier test fail

15. [BUG MERGE]

Symptom : When use multiboot or Expressboot tool to upgrade the firmware,

sometimes will fail.

Condition:

Step 1: Connect a PC to Ethernet switch and configure static IP setting for the PC

ZyXEL Confidential

7/34

Step 2: Doubly click the specific ExpressBoot tool or Multiboot tool, then click "Start"

button to send the packets containing the content of firmware.

Step 3: Connect the device to switch, then power on the device and the firmware

upgrade will be accomplished automatically

Step 4: Sometimes the devices' power light will become dark to imply that upgrading is

fail.

Modification in V3.40(APR.3)b2| 06/23/2008

16. Change modem code to 3.10.9.0.

17. Change default rom file.

Replace “wan dmt2 db tlb 25”by “wan dmt2 db tlb 10”in autoexec.net.

18. [BUG FIX]

SPRID:080321283

Symptom: WLAN client can’t contact with Ethernet LAN client after enable MBM in

LAN and WLAN direction.

Condition: Topology

PC1 -------------wired--------------------------P660HW-T1 v2-------------- Interenet

PC2---------wireless LAN-------------------

Step1. Default romfile

Step2. Enable MBM in LAN and WLAN interfaces, and set a Bandwidth, such as

1000000kbps.

Step3. WLAN PC ping LAN PC, request time out, it can’t connect to LAN PC.

19. [BUG MERGE]

SPRID: 080321275

Symptom: CPE is in RFC1483/ Routing mode, after dsl sync up and get a IP.Then we

do the tracert on our CPE , CPE will crash in condition that CPE don’t configure any

DNS mannually. .

Condition: CPE is in RFC1483/ Routing mode, after dsl sync up and get a IP.Then we

do the tracert on our CPE , CPE will crash in condition that CPE don’t configure any

DNS mannually.

The environment is simple , and we can reproduce it in our PQA lab. Using RFC

1483/Routing mode , then once we do the tracert on CPE,(ip traceroute), device will

crash.

Note: not only for 1483 route mode, enet encap also has this issue

20. [BUG MERGE]

SPRID: 080403231

Symptom: Use IPTV watch movie and use wireless LAN to do FTP download,about

half an hour device will crash.

Condition:

Step1.configure remote node 1 to bridge mode,and set IPTV to watch movies.

Step2.wireless use WPA-PSK ,LAN PC open seru,wireless LAN download files from

LAN PC,about half an hour device will crash.

21. [BUG MERGE]

SPRID: 080320220

Symptom: set IPTV application to group 3 (or group 4…), the IPTV can’t broadcast.

ZyXEL Confidential

8/34

Condition:

1) default romfile, then enable triple play.

2) edit ”sys tri port groupset 3 LAN 3 PVC 3”, and edit remote node 3 to bridge mode.

3) connect IPTV server,user can not watch IPTV program,but if set to group 1 or 2, it

will be ok

22. [BUG MERGE]

SPRID: 080320226

Symptom: Triple Play of two routers PVC with dynamic IP doesn’t work correctly.

Condition:

Step1.default romfile

Step2. Configure two routes with dynamic IP.

Step3. set LAN 1 PVC 1 to group 3 (or group 4…), the traffic from LAN 1 can go out

through both PVC1 and PVC2.But if set to group 1 or 2, it is ok,the traffic from LAN 1

can only go out through PVC1.

23. [BUG MERGE]

SPRID: 080403225

Symptom: PPP Config Wizard Security Issue

Condition:

1) Connect the device with PPPoE DSL line, then fill right VPI/VCI.

2) Fill wrong PPPoE username/password;

3) Open a website, for example: www.sina.com.cn; We can get a page

http://192.168.1.1/zCfgPPP.html to ask users to fill ”System Password”, ”User Name”

& ”Password”;

4) If I fill another“User Name”&“Password”and leave“System Password”as empty,

the“User Name ”&“Password”still can be saved and work on device. It will cause the

security concern.

24. [BUG MERGE]

SPRID: 080403232

Symptom: change ADSL modulation type in GUI or use CI Command ”wan adsl

opencmd XX’, the DSL Mode is error,after reboot ,it can show right mode

Condition:

change ADSL modulation type in GUI or use CI Command ”wan adsl opencmd

XX’,the DSL Mode is error,after reboot ,it can show right mode

25. [FEATURE ENHANCE]

Symptom: Support Annex M and READSL by command “wan adsl opencmd XX”.

26. [BUG MERGE]

SPRID: 080604229

Symptom: Crash when cpoying files to shared folder

Condition:

P660HW-T1 v2 -----------LAN----------Windows XP Pro PC (192.168.1.33)

---Wireless LAN-----Vista Laptop (192.168.1.34)

1. Connnect to a shared folder on the XP PC via the Vista laptop;

2. Create a new folder in the shared folder of XP PC.

3. Copy some files from Vista laptop to the new folder in the shared folder of XP PC.

ZyXEL Confidential

9/34

4. Crash happens on P660HW-T1 v2.The dump message is attached, which is same

with the customer’s.

27. [BUG MERGE]

SPRID: 080429313

Symptom: Connect DUT with G202, AG-225H or AG220 client and WPK2-PSK

mode, DUT will crash

Condition:

Topology: AP)))))) DUT

Step1: default romfile

Step2: In GUI＞Wireless LAN, Security Mode choose WPA2-PSK, and input

Pre-Shared Key, apply.

Step3: use G202, AG-225H or AG220 client to connect DUT with WPA2-PSK mode,

DUT will crash, or client can connect DUT successfully, but after a while, DUT crash.

28. [BUG MERGE]

SPRID: 080418858

Symptom: Device will crash when lan connect with a P-2302RL-P1, which will send

out a ICMP packet (Dst is 224.0.0.1)

Condition:

Customer connect the P-2302RL-P1 to P-660HW-T3v2, no wan connection , device

will crash. RD check the crash dump , is should related to the point about IGMP.

We here use customer’s packet trace , generate the ICMP(DST is 224.0.0.1), then

connect the PC to lan side , when the packet is sent , device will crash.

The crash dump and packet trace is attached. (The packet we generated is the index 55)

Some other device will also suffer this issue

29. [BUG MERGE]

SPRID: 080125309

Symptom: P660HW-T1 v2 WLAN encryption set WPA2-PSK, uses G202 connect to it,

device crash.

Condition:

G202 Driver 6.6.0.0, Utility 2.0.2.In XP OS, just use utility to connect to P660HW-T1

v2 using WPA2-PSK, the device will crash.

Modification in V3.40(APR.3)b1| 03/13/2008

1. Change cpu from P2F(P3) to P2H base on 3.40(APR.2)C0

3. Change modem code from 3.5.18.8 to 3.10.1.0

4. Change HW version from 1 to 2 for support P2H

5. [BUG FIX]

[Symptom]: User can get rom-0 via http://<IP Address>/rom-0 without authentication.

[Condition]: N/A

6. [BUG FIX]

[Symptom]: Device will crash when running p2p download over Wi-Fi with pppoe

encapsulation and firewall on.

[Condition]: N/A

7. [BUG FIX]

ZyXEL Confidential

10/34

[Symptom]: device will crash will pppoa and syslogs active

[Condition]: 1.configure device and make it can access internet.

2. In GUI, Maintenance > Logs > Log Settings, active syslog Logging and

enter a Syslog Server Address.

3. In GUI, Maintenance > Logs > Log Settings, acitve all the Log.

4. When get wan IP, access internet, refresh lots of web pages.

5. Then it will crash when you want to configure device via GUI

8. [BUG FIX]

[Symptom]: When using CI command "sys adjtime", it shows "Where is your time

server? Please use menu 24.10 to set up", the information is not suitable on the models

that have not SMT.

[Condition]: 1. in web GUI Maintenance > System > Time Setting choose Manual

model or in CI command sys timeserver protocol choose 0[none]

2. when using CI command sys adjtime, it shows Where is your time

server? Please use menu 24.10 to set up

9. [BUG FIX]

[Symptom]: Firewall schedule can't work correctly.

[Condition]: Set 2 rules with same policy, different schedule. Only the 1st one

can work.

10. [BUG FIX]

[Symptom]: device will crash will pppoa and syslogs active

[Condition]: 1.encap pppoa

2.In GUI, Maintenance > Logs > Log Settings, active syslog Logging and

enter a Syslog Server IP Address.

3.In GUI, Maintenance > Logs > Log Settings, acitve Log "System

Maintenance".

4.when DSL up, the device will crash.

11. [Bug Fix] SPRID:070427319

[Symptom]:In remote management dns port can't be work after change.

[Condition]: N/A

12. [BUG FIX]

[Symptom]:RTP packet on PVC3 will leak to PVC1 while tripleplay is enable.

[Condition]:N/A

13. [BUG FIX]

[Symptom]: In bm rule setup page, if leave the rule name blank and then apply. it can

not enter this page again no matter you choose any other items.

[Condition]:

Step1: Enter GUI->MBM page, select user defined to enter rule setup page.

Step2: Fill in other parameter and leave rule name blank, then click apply to save

this rule.

Step2: In MBM page, on matter you select any choose, it can not enter the rule

setup page again.

14. [BUG FIX]

[Symptom]:Enable tripleplay, if the port not in any group, the packet from it will not go

out from the unmaped PVC.

[Condition]:

Inhaltsverzeichnis

Andere ZyXEL Communications WLAN-Router Handbücher

ZyXEL Communications

ZyXEL Communications NBG6816 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications P-2602HWUDL-D Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications VSG1432-B101 START V1.10 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications 3G Wireless Router NBG410W3G Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications VMG8924 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications MAX-207HW2R Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications G-4100 v2 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications ARMOR G5 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications P-334U Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications NBG-419N Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications Multy X WSQ50 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications NBG-4615 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications NBG-418N Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications P-330W Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications ARMOR G1 NBG6818 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications NBG-415N Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications NR Series Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications NBG2105 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications NBG 5715 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications P-336M Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications P-334U Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications P-334WT Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications 760559122614 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications NBG2105 Bedienungsanleitung

Beliebte WLAN-Router Handbücher anderer Marken

Airlogic

Airlogic AirSync Class 1 Betriebsanleitung

Samsung

Samsung WCH730B Bedienungsanleitung

NETGEAR

NETGEAR PowerLINE WiFi 1000 Series Bedienungsanleitung

Askey

Askey RAC2V1K Bedienungsanleitung

Alloy

Alloy WLF2454AP-S Bedienungsanleitung

TELEFONICA

TELEFONICA USB Adapter Bedienungsanleitung

TP-Link

TP-Link TL-WR542G Bedienungsanleitung

Hama

Hama 53120 Bedienungsanleitung

Intellinet

Intellinet 524582 Bedienungsanleitung

Asus

Asus RT-N10P Bedienungsanleitung

D-Link

D-Link DIR-506L Bedienungsanleitung

Sapido

Sapido GR297n Bedienungsanleitung

Asus

Asus DSL-N55U Bedienungsanleitung

AMTC

AMTC WR7502 Bedienungsanleitung

Compaq

Compaq CP-2W - iPAQ Connection Point Bedienungsanleitung

SMC Networks

SMC Networks WBR14-N2 FICHE Bedienungsanleitung

Draytek

Draytek Vigor2120 Series Bedienungsanleitung

Sitecom

Sitecom WLR-4000 Bedienungsanleitung