3D Systems ProJet 6000 Bedienungsanleitung

3D SYSTEMS CONFIDENTIAL

Title: Work Instruction – ProJet 6000/7000 Manual Resin Stirring Procedure

Doc: 283584-00 Description: ProJet 6000 and 7000

Rev: ADate: 9/11/14 Page: 1of7

Purpose: To provide step-by-step work instructions for manually stirring the vat in the ProJet 6000 and

7000 printers.

Tools & Supplies Required:

•Nitrile gloves

•Safety goggles

•Lab coat

•Absorbent paper towels

•3/8” to 1/2” variable-speed drill (cord or cordless) which can operate to stir resin for at least 30

minutes.

•A propeller which has a long shaft stem and can be attached to the drill for mixing. The total length

of the propeller should not be longer than 6” (15cm).

Example propeller

3D SYSTEMS CONFIDENTIAL

Title: Work Instruction – ProJet 6000/7000 Manual Resin Stirring Procedure

Doc: 283584-00 Description: ProJet 6000 and 7000

Rev: ADate: 9/11/14 Page: 2of7

•Open the machine door and remove the platform from the system (if it is in the system)

•Close the door. When alerted, select “Yes” to turn the power back on.

•Go to the “Advanced” screen, select “Elevator/Leveler,” and select “Home.”

•Wait for the elevator to move to the home position.

•Enter “-5” in the “Distance” box and select “Move Elevator.”

•Wait for the elevator to reach the bottom limit.

3D SYSTEMS CONFIDENTIAL

Title: Work Instruction – ProJet 6000/7000 Manual Resin Stirring Procedure

Doc: 283584-00 Description: ProJet 6000 and 7000

Rev: ADate: 9/11/14 Page: 3of7

•Go to the “Advanced” page, select “Print Applicator,” and select “Park.”

•Wait for the print applicator to move to the park position.

3D SYSTEMS CONFIDENTIAL

Title: Work Instruction – ProJet 6000/7000 Manual Resin Stirring Procedure

Doc: 283584-00 Description: ProJet 6000 and 7000

Rev: ADate: 9/11/14 Page: 4of7

•Go to the “Advanced” screen and select “Elevator/Leveler.”

•Select “Drain Print Tray.”

•Let the resin drain until the resin level in the print tray is about 2” below the rim.

•Install the propeller shaft to the drill.

•Ensure that you have the appropriate protective equipment on (gloves, googles, lab coat).

•Open the machine door.

•Remove any visible debris in the print tray.

3D SYSTEMS CONFIDENTIAL

Title: Work Instruction – ProJet 6000/7000 Manual Resin Stirring Procedure

Doc: 283584-00 Description: ProJet 6000 and 7000

Rev: ADate: 9/11/14 Page: 5of7

•Put the propeller at the stirring position. The stem should form a 45-60° angle with the

horizontal plane.

•The propeller should be submerged at the center of the print tray.

•Turn on the drill and slowly increase the rpm until it reaches the highest rpm without the

resin overflowing.

•Stir the resin for about 30 minutes.

•During the stirring procedure, debris may collect around the propeller or show up on the

resin surface. If this occurs, stop stirring and remove the debris.

•When you have finished stirring, remove the drill and place the drill and propeller in an

appropriate location, supporting them with absorbent paper towels to avoid spilling excess

resin on any surfaces.

Drill with propeller submerged in the

resin at the proper angle for stirring

3D SYSTEMS CONFIDENTIAL

Title: Work Instruction – ProJet 6000/7000 Manual Resin Stirring Procedure

Doc: 283584-00 Description: ProJet 6000 and 7000

Rev: ADate: 9/11/14 Page: 6of7

•Close the machine door.

•When alerted, select “Yes” to turn the power back on.

•Go to the “Advanced” page, select “Elevator/Leveler,”and select

“Offload.”

•Wait for the elevator to move to the offload position.

•Open the machine door and install a clean platform.

•Close the machine door.

•When alerted, select “Yes” to turn the power back on.

•Select “Start.” Wait for the elevator to move to the start position.

•In the “Elevator/Leveler” menu, select “Level” to level the resin.

•When the resin level reading reaches roughly 31.000, select “Stop” to stop leveling.

•In the “Elevator/Leveler” menu, select “Home.”

•Wait for the elevator to home.

•Wait for large bubbles and micro-bubbles to disappear.

•The system is now ready for part building.

3D SYSTEMS CONFIDENTIAL

Title: Work Instruction – ProJet 6000/7000 Manual Resin Stirring Procedure

Doc: 283584-00 Description: ProJet 6000 and 7000

Rev: ADate: 9/11/14 Page: 7of7

END OF PROCEDURE

•To clean the drill and propeller, take them to a room away from the machine and wipe

down with isopropyl alcohol and paper towels.

•The drill components may then be post-cured in a Post Curing Apparatus (PCA) for at least

45 minutes on each side, making them safer for handling.

Andere Handbücher für ProJet 6000

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere 3D Systems 3D-Drucker Handbücher

3D Systems

3D Systems CubePro Bedienungsanleitung

3D Systems

3D Systems ProJet 5000 Bedienungsanleitung

3D Systems

3D Systems CUBE Bedienungsanleitung

3D Systems

3D Systems CUBE Bedienungsanleitung

3D Systems

3D Systems ProJet 3500 Max Series Bedienungsanleitung

3D Systems

3D Systems iPro 8000 SLA Center Bedienungsanleitung

3D Systems

3D Systems ProX 500 Bedienungsanleitung

3D Systems

3D Systems wematter Density Bedienungsanleitung

3D Systems

3D Systems CUBE Bedienerhandbuch

3D Systems

3D Systems wematter Atmosphere Bedienungsanleitung

3D Systems

3D Systems CubePro Bedienungsanleitung

3D Systems

3D Systems Geomagic Touch Bedienungsanleitung

3D Systems

3D Systems Cubify CUBEX Duo Stücklistenhandbuch

3D Systems

3D Systems Figure 4 Standalone Bedienungsanleitung

3D Systems

3D Systems CubePro Bedienungsanleitung

3D Systems

3D Systems sPro Bedienungsanleitung

3D Systems

3D Systems Figure 4 Standalone Handbuch

3D Systems

3D Systems CubePro Bedienungsanleitung

3D Systems

3D Systems CubePro Stücklistenhandbuch

3D Systems

3D Systems Viper Pro SLA iPro 8000 Bedienungsanleitung

3D Systems

3D Systems CubePro Gebrauchsanweisung

3D Systems

3D Systems PostCure 1050 Bedienungsanleitung

3D Systems

3D Systems CubePro Bedienungsanleitung

3D Systems

3D Systems ProX DMP 300 Bedienungsanleitung

Beliebte 3D-Drucker Handbücher anderer Marken

Ultimaker

Ultimaker S5 Material Station Bedienungsanleitung

EcubMaker

EcubMaker TOYDIY Bedienungsanleitung

AnyCubic

AnyCubic Kossel Plus Bedienungsanleitung

ReDeTec

ReDeTec ProtoCycler Bedienungsanleitung

Kywoo3D

Kywoo3D Tycoon IDEX Bedienungsanleitung

CraftBot

CraftBot PLUS PRO Bedienungsanleitung

3DGence

3DGence INDUSTRY F340 Bedienungsanleitung

HP Jet Fusion 4200 Betriebsanleitung

Rokit

Rokit AEP Series Bedienungsanleitung

AnkerMake

AnkerMake M5 Bedienungsanleitung

DIYElectronics

DIYElectronics PRUSA I3 Montageanleitung

Ackuretta

Ackuretta FreeShape 120 Bedienungsanleitung

LONGER

LONGER LK5Pro Bedienungsanleitung

Stratasys

Stratasys J850 Bedienungsanleitung

MakerBot

MakerBot Replicator Bedienungsanleitung

Stratasys

Stratasys FDM Vantage Series Bedienungsanleitung

ZYYX

ZYYX Pro II Bedienungsanleitung

FLASHFORGE 3D PRINTER

FLASHFORGE 3D PRINTER Creator Benutzerhandbuch