3M VF-45 Bedienungsanleitung
VF-45™ Fiber Optic Connector
Quick Install Kit
Instructions
January 2004
78-8097-8734-0-D
2
• Cable Jacket Stripper
• Snips
• Buffer Stripper
• Duplex Stripper
• Puck Assembly
• Cotton Swabs
• Lint Free Cloths
• Alcohol Bottle
• Polishing Station
• Lapping Film
• Carrying Case
• Tool Pouch
• Instructions
• Cleaning Wires
• Fiber Microscope (with three adapters and case)
• Removable Cleave Blade
1.0 3M™ VF-45™ Fiber Optic Connector Quick Install Kit Contents
Warning: Do not touch cleave blade. Any material or solvent that contacts the blade can cause damage.
3
2.0 Features
The 3M™ VF-45™ Fiber Optic Connector Quick Install Kit is used to field terminate VF-45 multimode and single
mode sockets. The VF-45 sockets are dual optical fiber connectors that are primarily used in fiber-to-the-desk LAN
applications. The duplex fibers are terminated simultaneously using this tool kit.
The VF-45 Fiber Optic Connector Quick Install Kit has the following hardware features and benefits:
a) Carrying case for ease of use with compartments for all required tools.
b) Integrated installation tool comprising:
• Easy scribe and break of fibers to prepare for polishing
• Fiber stub catcher
• Slip resistant polishing base
• Tool pouch storage for all hand tools
• Adhesive backed lapping film for polishing
• Versatile dual illumination microscope with adapters for inspection of:
1) Polishing puck end-face
2) Patch cord plug-fibers
3) Standard ferruled connectors
c) All fiber measurements made with hand tools (no precise measuring)
d) Easy fiber insertion and socket assembly
e) Audible click verifies socket assembly
f) Cleaning with cotton swab
g) Quick assembly of VF-45 socket
h) Angle polishing for low loss, low reflectance connections
i) Replaceable polishing pad
j) Replaceable scribe assembly
k) Replaceable polishing face
Caution: Wear safety glasses during all work operations.
4
a
cb
d
3.0 3M™ VF-45™ Socket
3.1 Contains the following:
a) Housing c) Boot
b) Socket fiber holder (SFH) d) Base
Note: The VF-45 Socket is sold separately.
4.0 Installation
4.1 Position polishing base.
At the patch panel area, place the polishing base on the
patch panel work tray or on a nearby suitable surface. At
the work area outlet, choose a suitable surface. Open the
hinged scribe cover.
Attach a sheet of lapping film to polishing surface of the
station. Removal of the release liner from lapping film
exposes adhesive backing to secure the lapping film to the
polishing surface.
Tech Tip: Before placement of the lapping film, clean the
polishing surface with a lint free wipe moistened
with isopropyl alcohol. Lapping film will last for
about 50 connectors.
Tech Tip: All Isopropyl Alcohol should be reagent grade, 99%
or better. The use of inferior alcohol will adversely
effect interconnect losses. This can be purchased
from a chemical supply house.
5
Note: Carefully follow safety, health and environmental
information on container label or Material Safety Data
Sheet for isopropyl alcohol being used.
4.2 Position the polishing puck assembly.
Remove the polishing puck assembly from the storage
compartment beneath the polishing pad and place it on
the dovetail on top of the hinged scribe cover.
Open the top of the polishing puck assembly by
unlatching it from the side and opening it by its hinge to
expose the inner cavity.
4.3 Position socket fiber holder in polishing puck
assembly.
Ensure that the cavity is clean of debris and that the face
of the puck is in the up position. Position a socket fiber
holder into the cavity of the polishing puck assembly.
Tech Tip: Do not press on the activation cap of the SFH
during insertion. It should be held by the four
prongs only. (See insert)
6
4.4 Adjust the jacket stripper so they cut only the outer jacket
and not the Kevlar® strands. Move the stop location
with a small, flat-head screwdriver until the hole size is
correct.
4.5 Remove outer cable sheath.
Cut outer cable jacket at a length of 1 meter (39 in.) and
set tool aside.
7
Remove the outer sheath by pulling on the end of the
cable jacket, sliding it off the Kevlar® strands and inner
optical fiber buffer tubes. Do not use the tool to slide the
outer jacket off the inner Kevlar strands and buffer tubes.
Discard the outer jacket.
4.6 Remove Kevlar strands.
Use the snips to cut the Kevlar strands flush with the
cable jacket. Discard the strands.
Use a cable tie to strain relief cable in patch panel or
outlet within 2.5 mm (1 in.) of end of sheath.
Note: Do not over tighten the cable tie around the cable jacket.
Pinched fibers may experience optical power loss.
8
4.7 Even-up the fiber and buffer tube.
If the fiber extends past the buffer tube, trim the
end so the tube and fibers are the same length.
4.8 Position boot.
Place the boot onto the buffer tube, small end
first. Slide the boot along the buffer tube until it
is out of the way.
9
4.9 Remove buffer tube.
Verify that length guide is pushed flush against
back of tool. Insert the buffer tube into the buffer
tube stripper until it bottoms against the tool.
Squeeze the handles of the tool together and
pull the buffer tube off to expose the two 250 µ
optical fibers.
4.10 Strip the buffer coating from the fibers.
Insert both of the 250 µ fibers into the tube guide
of the dual fiber stripper until the buffer tube
is flush with the outer edge of the tube guide.
Squeeze the handles of the dual fiber stripper
together and pull the fibers out.
Note: Clean the stripper blades with the brush end of
the cleaning tool when needed. See “Dual Fiber
Stripper Maintenance” section.
10
orange
blue
4.11 Clean the fibers.
Moisten a section of a lint-free wipe with isopropyl
alcohol. Wipe the residue from the fibers using the
moistened lint-free wipe until the fibers squeak.
Tech Tip: All Isopropyl Alcohol should be reagent grade, 99%
or better. The use of inferior alcohol will adversely
effect interconnect losses. This can be purchased
from a chemical supply house.
Caution: Care should be used when handling fibers so as not
to break them, or to handle them in such a way that
they could penetrate your skin.
Note: Carefully follow safety, health and environmental
information given on container label or Material Safety
Data Sheet for isopropyl alcohol being used.
4.12 Thread the fibers into the holder.
Spread the fibers slightly apart between your fingers
to feed them into the socket fiber holder. Refer to
label inside polishing puck for duplex A-B crossover
orientation. (e.g., patch panel A-to-B, outlet B-to-A).
Every link must cross (i.e. patch panel to patch panel).
Tech Tip: Make sure that the face of the polishing puck
assembly is in the closed position before the fibers
are inserted.
Inhaltsverzeichnis
Andere 3M Kabel und Steckverbinder Handbücher
3M
3M Litmann Quality 3100 Bedienungsanleitung
3M
3M ECAM-20 MM-D Bedienungsanleitung
3M
3M Scotchlok U1 Series Bedienungsanleitung
3M
3M Fibrlok II 2539 Bedienungsanleitung
3M
3M 7700 Series Betriebsanleitung
3M
3M 4655 Bedienungsanleitung
3M
3M Cold Shrink QT-III 7620-S-INV-3G Series Bedienungsanleitung
3M
3M 5810-BI-15 Bedienungsanleitung
3M
3M Liqui-Cel MM 0.5x1 Series Handbuch
3M
3M 3104 Bedienungsanleitung
3M
3M 10350-1230 Bedienungsanleitung
3M
3M 5458A-IJ Bedienungsanleitung
3M
3M 4075 Leitfaden
3M
3M 103 12R1-00 Series Bedienungsanleitung
3M
3M ReLoad SRL Bedienungsanleitung
3M
3M 50P Referenzhandbuch
3M
3M 8250 Montageanleitung
3M
3M 5811 Series Bedienungsanleitung
3M
3M SafeLok Anchorage 4011 Leitfaden
3M
3M 3443-107N Montageanleitung
