3M The Edge Bedienungsanleitung
Turning on
1. To turn on the Edge, press the on/off
enter key.
The start-up screen will appear
indicating the model and firmware
version. Then, the measurement
view will display.
Resetting
Resetting the dosimeter is performed
using QSP-II software via the clear tab
from the Edge Set-up button.
The Edge may also be reset using the
keypad. (See Chapter 3 and Chapter 4 in
the Edge user manual for details.)
Navigating
1. Press the up/down arrow key to
navigate through measurement values,
battery condition, and run time.
Setting-up the Edge
All the Edge parameters are set up via
QSP-II software. (See
Chapter 3 in the Edge user manual for
details).
Calibrating
1. Remove the windscreen.
2. Ensure The Edge is turned on and
stopped.
3. Slide the Edge into the mouth of the
calibrator (ensuring the adapter ring is
inserted into the calibrator).
4. Turn on the calibrator. Ensure the
calibrator is set to 114 dB and 1000 Hz.
See subsequent steps on backside.
1
2
3
4
5 6
7
1. Windscreen & Microphone
2. LED indicator
Red –indicates dose has
exceeded the alarm level.
Amber –indicates
stopped.
Green –indicates
measuring.
3. Measurement display
4. Up arrow
5. Run/Stop key
6. On/Off Enter key
7. Down arrow
Turning off
1. Press and hold the on/off enter
key for the count down.
Reviewing results
Data is downloaded to QSP-II for
analysis, managing, file storage, and
printing. (See “Downloading” in the
Edge user manual for
details.)
Locking and unlocking
1. Turn the dosimeter on and press
the run/stop key to start
measuring.
2. To enable lock, press run/stop
Key three consecutive times
within one second intervals.
The
Lock screen will appear.
3. To unlock, press the run/stop
key 3 consecutive times
within one second intervals. Then
press on/off enter key.
5. “CAL” will flash on the display.
6. Press the on/off enter to
trigger the calibration display.
7. To adjust the calibration value on
the display, repeatedly press the
up or down arrow.
8. When you have selected the
appropriate dB level, press
the on/off enter key.
A shaded bar will appear when
loading your calibration informa-
tion. Then a summary screen will
indicate the date and time.
9. To return to measurement
screen, press on/off enter
key.
Running a study
1. Once the dosimeter is turned on,
press and hold the run/stop
key.
A 3, 2, 1 countdown will appear.
Then, a run indicator will appear
on the top right of the display. Also,
the LED indicator will flash green
(unless you disabled this in QSP-II).
Ending a Study
1. While running a study, press and
hold the run/stop key.
Cal screen
www.questtechnologies.com
098-610, Rev. D, 3/11
Key indicator
Indicates dosimeter
is locked while
Padlock icon
Indicates measure-
ment values are
hidden during run.
Andere 3M Messgerät Handbücher
3M
3M GMI PS200 Series Handbuch
3M
3M TN2000 Handbuch
3M
3M SE-400 Series Bedienungsanleitung
3M
3M Clean-Trace Bedienungsanleitung
3M
3M SD-200 Bedienungsanleitung
3M
3M Tape Application Monitor Datenblatt
3M
3M CTM051 Bedienungsanleitung
3M
3M QUESTemp 44 Bedienungsanleitung
3M
3M 701 Handbuch
3M
3M SD-200 Bedienungsanleitung
3M
3M 725 Bedienungsanleitung
3M
3M Dynatel 965AMS Bedienungsanleitung
3M
3M ESD Pro Bedienungsanleitung
3M
3M Dynatel 2250ME Series Bedienungsanleitung
3M
3M Clean-Trace NGi Luminometer Bedienungsanleitung
3M
3M Dynatel 965AMS Bedienungsanleitung
3M
3M SoundPro SE Series Montage- und Bedienungsanleitung
3M
3M 965DSP/SA Bedienungsanleitung
3M
3M Dynatel 965AM Bedienungsanleitung
3M
3M SE-401 Bedienungsanleitung
