3M DBI-SALA Nano-Lok Connected Order Picker SRL... Bedienungsanleitung

3M™DBI-SALA

Nano-Lok™

Connected Order Picker

SRL System

Training Manual and Troubleshooting Guide

This training manual provides visuals and troubleshooting flow paths for the 3M™DBI-SALA®Nano-Lok™Connected

Order Picker SRL System. This guide does not replace the Instructions for Use document, which must be followed

for proper operation.

Purpose: This training manual and troubleshooting guide provides an overview of how to use the

3M™DBI-SALA®Nano-Lok™Connected Order Picker SRL System as well as troubleshooting

process flows. It is to be used as a supplement to the Instruction for Use document.

For technical assistance contact 3M Fall Protection at 800-328-6146.

3M™DBI-SALA®Nano-Lok™Connected Order

Picker SRL System

Training Manual and Troubleshooting Guide

Contents:

1. System Overview

2. Parts to Have on Hand

3. Video Demonstrations

4. Common Procedures

5. Troubleshooting

1. System Overview

Raymond OP

Alert Box

(8548924)

LED Light

Strips

(9515033)

Alert Box

Power Cable

(9515475)

Hyster-Yale OP

Connected

Order Picker

Self Retracting

Lifeline

(2000037)

Alert Box

(8548924)

Cab Mount

Bracket

(3100084)

Dual Sensing

Connected

Hook LED Light

Strips

(9515033)

Alert Box

Power Cable

(9515475)

Crown OP

Alert Box

(8548924)

Cab Mount

Bracket

(3100084)

LED Light

Strips

(9515033)

Alert Box

Power Cable

(9515475)

Connected

Order Picker

Self Retracting

Lifeline

(2000037)

Dual Sensing

Connected

Hook

Jungheinrich OP

Alert Box

(8548924)

Cab Mount

Bracket

(3100084)

LED Light

Strips

(9515033)

Alert Box

Power Cable

(9515475)

Connected

Order Picker

Self Retracting

Lifeline

(2000037)

Dual Sensing

Connected

Hook

3M™DBI-SALA®Nano-Lok™Connected Order

Picker Self Retracting Lifeline (2000037)

2. Parts to Have on Hand

Components Reference:

3M™DBI-SALA®Nano-Lok™Cab

Mount Bracket (3100084)

3M™DBI-SALA®Nano-Lok™Alert Box

(8548924)

3M™DBI-SALA®Nano-Lok™Alert Box Power

Cable (9515475)

3M™DBI-SALA®Nano-Lok™LED Light Strips

(9515033)

3M™Supplied Cable Ties

Parts to have on hand to service system if required:

�Batteries —2032. 3V coin cells

�Microfiber cloth

�Compressed air can

Parts to Have on Hand for Servicing

3. Video Demonstration Training

A | System Overview

B | System Verification Check

C | Bluetooth Pairing Process

D | Battery Replacement

E | Tie Off Alert Escalation

4. Common Procedures

4.1 Bluetooth Pairing:

Reference section 4.3 from the Instructions for Use document for detailed instructions.

1. Ensure that the carabiner on the SRL is not “sleeping” by twisting the carabiner gate 1-2 times to wake it up.

2. Push and hold the large button (~2 seconds) on the side of the Connected Sensor box until the LED lights display

a blue wave pattern.

3. Twist the carabiner gate 5-6 times quickly.

4. The LED lights will display a brief green wave pattern to confirm successful pairing.

5. System is paired.

4.2 Carabiner Battery Replacement:

Reference section 4.6 from the Instructions for Use document for detailed instructions.

1. Indications that the coin cell battery in the carabiners needs to be replaced are:

a. The LED lights will be red with yellow tips on the ends.

b. The small, diagnostic LED on the carabiner itself will blink red once every three seconds.

2. Open the battery cover (using a flat edge if needed) and flip open the black plastic cover to reveal the

battery and battery holder.

3. Carefully insert a flat edge under the battery and pry it out of the holder, being careful to press down on

the tabs of the holder in order to prevent tearing the holder off the circuit board.

4. Replace with new battery (ensure battery has identification side facing up).

5. Carabiner is powered when LED turns on.

6. Close battery cover (use a flat edge to press one or both tabs inwards on door to assist with closing).

4.3 System Verification Check for Connected Features:

1. Step onto platform and confirm LED lights are fully red.

2. If lights are not fully red and instead are red with blue tips at ends, twist carabiner gate to wake up carabiner.

If lights do not go fully red, do Bluetooth pairing procedure found in 4.1 prior to moving to step 3.

3. Step off platform and confirm lights go off.

4. Step back on platform and confirm lights go on and are fully red.

5. Tie off carabiner to metal D-ring and confirm lights flash green then go off.

6. Remove D-ring from carabiner and confirm lights go red.

5. Troubleshooting

5.1 Flowcharts for Safety Management:

The LED lights don't light up when I step on the OP

Is the OP power turned on?

Is the carabiner anchored to

something metal?

Is the power connector on the

sensor box screwed in fully?

Are the LED strips plugged

into the sensor box?

Is the power connector broken

off or seem damaged?

Yes, OP is powered on.

No, carabiner is not anchored.

Yes, power connector is

fully screwed in.

Yes, LED strips are plugged in.

No, the power connector looks

normal and undamaged.

Reset the carabiner baseline:

Twist the carabiner gate

5-6 times and look for a

green flashing light. Look for

momentary green flashing on

carabiner's diagnostic LED light.

Yes, the connector looks

damaged. RED TAG

No change, RED TAG

No, turned on OP power.

Problem resolved!

Yes, removed carabiner from

anchor. Problem resolved!

No, power connector wasn't

screwed in. Problem resolved!

No, plugged in LED strips.

Problem resolved!

“RED TAG” means to conspicuously label the device and equipment for examination/repair by an authorized and trained person

Andere 3M Sicherheitsausrüstung Handbücher

3M Protecta first Bedienerhandbuch

3M DBI Sala EXOFIT Bedienungsanleitung

3M Versaflo S Series Bedienungsanleitung

3M SafeClaw 4077 Bedienungsanleitung

3M Protecta Trolmatic Bedienerhandbuch

3M PELTOR TACTICAL 100 Bedienungsanleitung

3M DBI Sala 8566691 Bedienungsanleitung

3M Scotchcast 3817 Bedienungsanleitung

3M NANO-LOK Bedienungsanleitung

3M LAD-SAF Bedienungsanleitung

3M Bosun Chair Bedienungsanleitung

3M DBI SALA 2104700 Bedienerhandbuch

3M Protecta Carros AM401G Bedienerhandbuch

3M DBI-SALA Nano-Lok XL Bedienungsanleitung

3M DBI Sala Rollgliss R550 Bedienungsanleitung

3M DBI SALA Flexiguard 8530433 Bedienungsanleitung

3M Jupiter Powered Air Turbo Bedienungsanleitung

3M Versaflo S Series Bedienungsanleitung

3M DBI-SALA Delta Bedienungsanleitung

3M DBI SALA FlexiGuard SafRig Bedienerhandbuch

3M PROTECTA AM100 Bedienungsanleitung

3M DBI-SALA XE Series Bedienungsanleitung

3M Protecta Cabloc Bedienungsanleitung

3M PROTECTA AF725 Bedienerhandbuch

Beliebte Sicherheitsausrüstung Handbücher anderer Marken

Innova

Innova Xtirpa Bedienungsanleitung

bolle SAFETY

bolle SAFETY B810 Bedienungsanleitung

SHENZHEN FANHAI SANJIANG ELECTRONICS

SHENZHEN FANHAI SANJIANG ELECTRONICS A9060T Bedienungsanleitung

Hiltron security

Hiltron security POWER8E Leitfaden

Hatco

Hatco B-950P Bedienungsanleitung

Sitec

Sitec TX MATIC Bedienungsanleitung

TEUFELBERGER

TEUFELBERGER GRIP 12 Bedienungsanleitung

MSA

MSA PremAire System Bedienungsanleitung

AMC

AMC 1022M Series Bedienungsanleitung

Trinity

Trinity CASS S3 Bedienungsanleitung

CMC

CMC Helitack HotSeat Bedienungsanleitung

Force

Force P-35 Bedienungsanleitung

ACM

ACM SAFETY D200 Produkthandbuch

Honeywell

Honeywell Miller H-Design DuraFlex Bedienerhandbuch

ROCK

ROCK P-451 AS Bedienungsanleitung

Power first

Power first 2XYR7A Service-Handbuch

SCHUBERTH

SCHUBERTH SHP 28-C Bedienungsanleitung

Trango

Trango CINCH Bedienungsanleitung